Planet IPOE-175 User manual

Industrial IP67 1-Port 60W 802.3bt
PoE++ Injector
IPOE-175
User’s Manual

Table of Contents
1. Package Contents................................................................................. 3
2. Hardware Introduction .......................................................................... 4
2.1 Product Outlook............................................................................. 4
2.2 Power Input Port ........................................................................... 4
2.3 Data Input Port and 802.3bt PoE++ Output Port .............................. 5
2.4 LED Indicators............................................................................... 5
3. Installation .......................................................................................... 6
3.1 Installing Cable Gland with Power Cable and RJ45 UTP Cable ............ 6
3.2 Connecting Waterproof Cable Kit to the Outdoor PoE Injector ............ 6
3.3 Wall-mount Installation .................................................................. 9
3.4 Connecting IPOE-175 to PD ...........................................................10
3.5 Connecting IPOE-175 to PD ...........................................................10
4. ProductSpecications ..........................................................................12
Customer Support.....................................................................................14

3
1. Package Contents
Thank you for purchasing PLANET Industrial IP67 1-port 10/100/1000/2500T
802.3bt PoE++ Injector, IPOE-175. In the following sections, the term
“Outdoor PoE Injector” means the IPOE-175.
Open the box of the Industrial Ethernet Switch and carefully unpack it. The
box should contain the following items:
IPOE-175 x 1 QR code sheet x 1 Wall-mounted Kit x 1
Spanner x 1
Power Cable with 2-pin
Terminal Block x 1
M22 Waterproof Cable
Gland x 3
Ground Wire x 1
If any of these are missing or damaged, please contact your dealer
immediately; if possible, retain the carton including the original packing
material, and use them again to repack the product in case there is a need to
return it to us for repair.
Remarks: The color of the ground wire is dierent according to the batch, but
itswirespecicationsmeetthestandard.

4
2. Hardware Introduction
This section describes the functionalities of the outdoor PoE Injector’s
components.
2.1 Product Outlook
Unit: mm
PoE-
in-Use
PoE++
Data
IPOE-175
PWR
DC Input Range:
24-56V , 4A max.
V+
Figure 2-1: IPOE-175 product outlook
2.2 Power Input Port
Figure 2-2 shows the power input port side of the IPOE-175
Figure 2-2: Power Input Port

5
2.3 Data Input Port and 802.3bt PoE++ Output Port
Figure 2-3 shows the data input port and PoE++ output port side of the IPOE-
175.
PoE++ Output Port Data Input Port
Figure 2-3: Two RJ45 Ports
2.4 LED Indicators
LED Color Function
PWR Green Indicates it has power.
PoE-in-Use Amber Indicates the port is providing power.
To install the 2-pin Terminal Block Connector on the Outdoor PoE Injector,
simply follow the following steps:
Step 1: Insert positive DC power wire into V+, negative DC power wire into
V-, and grounding wire into Ground.
V+
V
-
2-pin
Step 2: Tighten the wire-clamp screws for preventing the wires from
loosening and plug them into the Wall-mount Gigabit Ethernet Router
1. The wire gauge should be in the range from 20 to 22 AWG.
2. The device must be grounded.

6
3. Installation
This section describes how to install the Outdoor PoE Injector and make
connections to it. Please read the following topics and perform the procedure
in the order being presented.
3.1 Installing Cable Gland with Power Cable and RJ45 UTP
Cable
The cable gland consists of the following:
3.2 Connecting Waterproof Cable Kit to the Outdoor PoE
Injector
Step 1: Turn clockwise to tighten the gland body connected to the Outdoor
PoE Injector.
Step 2: Plug the power cable connector into the power input port.

7
Step 3: Insert the sealing insert into the cable gland body.
Step 4: Attach the clamping nut to the cable gland to complete the cable
assembly.
Make sure the clamping nut is tightly attached to the cable
gland body and the sealing insert is squeezed tightly.

8
Step 5: Repeat Steps 1 to 4 for “Data” Input Port and“PoE (Data + Power)”
Output Port.
1. Use only the waterproof cable gland provided in the package
of the IPOE-175.
2. If the above installation procedure is not properly followed,
the warranty will be invalidated.
3. If the waterproof cable gland is found missing or damage,
please contact your local reseller where you purchased from.
11.31mm
40.78mm
5.00mm
30.22mm
29.80mm
20.18
13.72
14.00
30.10
4. Never use any waterproof cable gland that is not purchased
from PLANET or doesn’t have the same dimensions of the
IPOE-175; it will damage the device permanently.

9
3.3 Wall-mount Installation
To install the Outdoor PoE Injector on the wall, please follow the instructions
described below.
Step 1: Find the wall that you want to mount the Outdoor PoE Injector on.
Step 2: Refer to the picture below to screw the four screws on the wall
140.36mm
59mm
Step3: Use a screwdriver to screw them into the wall.

10
3.4 Connecting IPOE-175 to PD
Users MUST complete grounding wired with the device; otherwise, a sudden
lightning could cause fatal damage to the device.
Earth Ground
EMD (Lightning) DAMAGE IS NOT COVERED UNDER WARRANTY.
3.5 Connecting IPOE-175 to PD
Step 1: Connect the additional Cat5e/6/6A cable from the PoE++ Out of the
IPOE-175 to a remote PD.
DC Power Line (DC)
1000BASE-T UTP
PoE
1000BASE-T UTP with PoE
PoE
Power Data PoE IP Camera
IPOE-175
Data
100m
802.3bt PoE++
Power Supply
Power
DC
DC24-56V
Ethernet Switch
Step 2: The PoE++ Out port is the power injector which transmits DC
voltage to the Cat5e/6/6A cable and transfer data from the Data
source.