Planet ADE-3410 User manual

ADSL 2/2+ Router
ADE-3410 / ADE-3400v2 / ADE4400v2
User's Manual

Copyright
Copyright©2006 by PLANET Technology Corp. All rights reserved. No part of
this publication may be reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language or computer language, in any form or by any
means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise,
without the prior written permission of PLANET.
PLANET makes no representations or warranties, either expressed or implied, with
respect to the contents hereof and specifically disclaims any warranties,
merchantability or fitness for any particular purpose. Any software described in this
manual is sold or licensed "as is". Should the programs prove defective following
their purchase, the buyer (and not this company, its distributor, or its dealer) assumes
the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software. Further, this company reserves
the right to revise this publication and to make changes from time to time in the
contents hereof without obligation to notify any person of such revision or changes.
All brand and product names mentioned in this manual are trademarks and/or
registered trademarks of their respective holders.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
4. Consult the dealer or an experienced radio technician for help.
2

FCC Caution:
To assure continued compliance (example-use only shielded interface cables when
connecting to computer or peripheral devices). Any changes or modifications not
expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
Following two conditions: (1) This device may not cause harmful interference, and (2)
this Device must accept any interference received, including interference that may
cause undesired operation.
R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF
THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 9 March 1999 on
radio equipment and telecommunication terminal Equipment and the mutual
recognition of their conformity (R&TTE)
The R&TTE Directive repeals and replaces in the directive 98/13/EEC
(Telecommunications Terminal Equipment and Satellite Earth Station Equipment)
As of April 8, 2000.
WEEE
To avoid the potential effects on the environment and human health as a
result of the presence of hazardous substances in electrical and electronic
equipment, end users of electrical and electronic equipment should
understand the meaning of the crossed-out wheeled bin symbol. Do not
dispose of WEEE as unsorted municipal waste and have to collect such
WEEE separately.
Safety
This equipment is designed with the utmost care for the safety of those who install
and use it. However, special attention must be paid to the dangers of electric shock
and static electricity when working with electrical equipment. All guidelines of this
and of the computer manufacture must therefore be allowed at all times to ensure the
safe use of the equipment.
3

Revision
User’s Manual for ADSL 2/2+ Router
Model: ADE-3410 / ADE-3400v2 / ADE-4400v2
Rev: 1.0 (May 2006)
Part No. EM-ADE3410v1
4

Table of Contents
1. INTRODUCTION....................................................................................................7
1.1 FEATURE...........................................................................................................7
1.2 PACKAGE CONTENTS...................................................................................8
1.3 PHYSICAL DETAILS.......................................................................................9
2. INSTALLATION...................................................................................................12
2.1 SYSTEM REQUIREMENT............................................................................12
2.2 HARDWARE INSTALLATION....................................................................12
2.3 INSTALLING THE USB DRIVER ON A PC (ADE-3410) .........................14
2.4 CONFIGURING THE NETWORK PROPERTIES ....................................18
3 CONFIGURATION................................................................................................24
3.1 DETERMINE YOUR CONNECTION SETTINGS.....................................24
3.2 CONNECTING THE ADSL ROUTER TO YOUR NETWORK ...............24
3.3 CONFIGURING WITH WEB BROWSER...................................................25
3.3.1 QUICK SETUP GUIDE............................................................................26
3.3.2 SYSTEM TIME..........................................................................................30
3.3.3 ADMIN SETTING.....................................................................................30
3.3.4 FIRMWARE UPDATE.............................................................................31
3.3.5 SYSTEM LOG ...........................................................................................31
3.3.6 SYSTEM RESET.......................................................................................32
3.4.1 ADSL STATUS...........................................................................................33
3.4.2 ADSL STATISTICS...................................................................................33
3.4.3 VC CONFIGURATION............................................................................34
3.5.1 WAN CONFIGURATION........................................................................34
3.5.2 WAN STATUS ...........................................................................................35
3.5.3 DNS..............................................................................................................36
3.5.4 DDNS...........................................................................................................37
3.6.1 LAN CONFIGURATION .........................................................................38
3.7.1 IP FILTERING ..........................................................................................38
3.8.1 NAT SETTING...........................................................................................40
3.8.2 VIRTUAL SERVER..................................................................................41
5

3.8.3 DMZ SETTING..........................................................................................42
3.8.4 ADSL TYPE SETTING.............................................................................43
3.9.1 STATIC ROUTING...................................................................................43
3.9.2 DYMANIC ROUTING..............................................................................44
3.9.3 ROUTING TABLE....................................................................................44
3.10.1 SYSTEM STATUS...................................................................................45
3.11.1 ACCESS CONTROL LIST.....................................................................46
3.12.1 SIMPLE NETWORK MANAGEMENT PROTOCOL.......................46
3.13.1 UNIVERSAL PLUG and PLAY.............................................................47
3.14.1 SYSTEM DIAGNOSTICS ......................................................................48
APPENDIX A: GLOSSARY.....................................................................................49
6

1. Introduction
The PLANET ADSL 2/2+ Router, ADE-3410 / ADE-3400v2 / ADE-4400v2,
provides office and residential users the ideal solution for sharing a high-speed ADSL
2/2+ broadband Internet connection. It can support downstream transmission rates of
up to 24Mbps and upstream transmission rates of up to 3.5Mbps. The product
supports PPPoA (RFC 2364 - PPP over ATM Adaptation Layer 5), RFC 2684
encapsulation over ATM (bridged or routed), PPP over Ethernet (RFC 2516), and
IPoA (RFC1577) to establish a connection with ISP.
Via the user-friendly management interface, ADE-3410 / ADE-3400v2 /
ADE-4400v2 can be managed by workstations running standard web browsers.
Furthermore, the device provides DHCP server, NAT, virtual server, DMZ, access
control, IP filter, PPTP/IPSec/L2TP pass-through, DDNS, and UPnP capability.
The device also serves as an Internet firewall, protecting your network from being
accessed by outside users. It provides the natural firewall function (Network Address
Translation, NAT). All incoming and outgoing IPs are monitored and filtered.
Moreover, it can be configured to block internal users from accessing to the Internet.
1.1 Feature
Internet Access Features
Shared Internet Access. All users on the LAN can access the Internet through
the ADE-3410 / ADE-3400v2 / ADE-4400v2 using only a single external IP
Address. The local (invalid) IP Addresses are hidden from external sources.
This process is called NAT (Network Address Translation).
Built-in ADSL 2/2+ Modem. The device provides ADSL 2/2+ modem, and
supports all common ADSL connections.
IPoA, PPPoE, PPPoA, Direct Connection Support. Various WAN
connections are supported by ADE-3410 / ADE-3400v2 / ADE-4400v2.
Auto-detection of Internet Connection Method. In most situations, the
device can test your ADSL and Internet connection to determine the
connection method used by your ISP.
7

Fixed or Dynamic IP Address. On the Internet (WAN port) connection, the
device supports both Dynamic IP Address (IP Address is allocated on
connection) and Fixed IP Address.
Advanced Internet Functions
Virtual Servers. This feature allows Internet users to access Internet servers
on your LAN. The required setup is quick and easy.
Firewall. Supports simple firewall with NAT technology and provides option
for access control from Internet, like Web, FTP, Telnet, SNMP, ICMP, and
ALL services. It also supports DoS prevention and IP filtering.
Universal Plug and Play (UPnP) UPnP allows automatic discovery and
configuration of the Broadband Router. UPnP is supported by Windows ME,
XP, or later.
Dynamic DNS Support. DDNS, when used with the Virtual Servers feature,
allows users to connect to Servers on your LAN using a Domain Name, even if
you have a dynamic IP address which changes every time you connect.
VPN Pass through Support. PCs with VPN (Virtual Private Networking)
software using PPTP, L2TP, and IPSec are transparently supported - no
configuration is required.
RIP1/2 Routing. It supports RIP1/2 routing protocol for routing capability.
Simple Network Management Protocol (SNMP). It is an easy way to remotely
manage the router via SNMP.
LAN Features
Dual-Port. The ADE-3410 incorporates on one Ethernet port and one USB
port, making it easy to create or extend your LAN.
Ethernet Port. The ADE-3400v2 provides one Ethernet port, making it easy to
create or extend your LAN.
4-Port Switch. The ADE-4400v2 incorporates a 4-port 10/100BaseT switching
hub, making it easy to create or extend your LAN.
DHCP Server Support. Dynamic Host Configuration Protocol provides a
dynamic IP address to PCs and other devices upon request. The device can act
as a DHCP Server for devices on your local LAN.
1.2 Package Contents
‧ ADE-3410 / ADE-3400v2 / ADE-4400v2 Unit
8

‧ Power Adapter
‧ Quick Installation Guide
‧ User’s Manual CD
‧ RJ-11 (ADSL) cable
‧ RJ-45 cable
‧ USB cable (ADE-3410)
1.3 Physical Details
Top-mounted LEDs of ADE-3410
Top-mounted LEDs of ADE-3400v2
9

Top-mounted LEDs of ADE-4400v2
LED Indicator
LED Meaning
1 PPP : Lit steady when there is a PPPoA / PPPoE
connection.
2 ADSL: Lit when successfully connected to an ADSL
DSLAM (“linesync”).
3 USB: Lit when the USB port is connected to the PC
and working properly (ADE-3410).
4 LAN: Lit when connected to an Ethernet device.
Green for 100Mbps; Orange for 10Mbps.
10

Blinking when data is Transmitted / Received.
5 SYS: Lit when the system is ready.
6 PWR: Lit when power is ON.
Rear Panel of ADE-3410
Rear Panel of ADE-3400v2
Rear Panel of ADE-4400v2
Port Meaning
1 Power
Switch Power ON/OFF switch (ADE-3410).
2 12V
Connect the supplied power adapter to this
jack (ADE-3410 / ADE-3400v2: 12V AC;
ADE-4400v2: 12V DC).
3 RESET
After the device is powered on, press it to reset
the device or restore to factory default settings.
Reset the device 6 seconds above to restore the
factory default settings (this is used when you
11

can not login to the router, e.g. forgot the
password)
4 LAN
Connect a UTP Ethernet cable (Cat-5 or
Cat-5e) to one of the four LAN ports when
connecting to a PC or an office/home network
of 10Mbps or 100Mbps.
5 USB
Connect the supplied USB cable to this port
when connecting to the PC (ADE-3410).
6 ADSL
Connect the supplied RJ-11 (“telephone”)
cable to this port when connecting to the
ADSL/telephone network.
2. Installation
This chapter offers information about installing your router. If you are not familiar with
the hardware or software parameters presented here, please consult your service
provider for the values needed.
2.1 System Requirement
1. Personal computer (PC)
2. Pentium II 233 MHz processor minimum
3. 32 MB RAM minimum
4. 20 MB of free disk space minimum
2.2 Hardware Installation
This section describes how to connect and configure the ADE-3410, ADE-3400v2, and
ADE-4400v2.
ADE-3410
12

USB
Cable
ADSL
Line
PC /
Hub
Power
Adapter
ADE-3400v2
ADSL
Line
PC /
Hub
Power
Adapter
ADE-4400v2
PC /
Hub
ADSL
Line
Power
Adapter
13

2.3 Installing the USB Driver on a PC (ADE-3410)
If you connect the device through USB port instead of Ethernet port, Windows will
automatically detect the device when the USB cable is connected to the PC at the first
time. Please follow the steps to install the USB driver.
For Windows XP & 2000：
1. Start Windows. Then insert the installation CD into the CD-ROM drive. In next
window, to specify the driver directory such as “G:\USB
Driver\setupXP2K_En_De_Fi” and to continue.
2. Choose the setup language and click “Next” (There are three languages that
user can choose: English, German, and French).
14

3. Then follow screen.
4. Click the type of setup you prefer, then click “Next”.
15

5. Setup enough information of coping the program files then click “Next”.
6. Please plug USB cable into ADSL USB Modem.
16

7. Click “Finish”.
8. The windows will show the screen and please enter “User Name” and
“Password” to configure the status report on web page.
For Windows 98 & Me：
1. Start Windows. Then insert the installation CD into the CD-ROM drive. In next
window, to specify the driver directory such as “G:\USB Driver\setup98
Me_En_De_Fi” and to continue.
17

2. Choose the setup language and click “Next”. (There are three languages that user
can choose: English, German, and French)
3. Then follow screen.
4. Click the type of setup you prefer, then click “Next”.
5. Setup enough information of coping the program files.
6. Select “I want to restart my computer now” and click OK.
7. Click “Finish”.
2.4 Configuring the Network Properties
18

Configuring PC in Windows XP
1. Go to Start / Control Panel (in Classic View). In the Control Panel,
double-click on Network Connections
2. Double-click Local Area Connection.
3. In the Local Area Connection Status window, click Properties.
4. Select Internet Protocol (TCP/IP) and click Properties.
19

5. Select the Obtain an IP address automatically and the Obtain DNS
server address automatically radio buttons.
6. Click OK to finish the configuration.
Configuring PC in Windows 2000
1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on
Network and Dial-up Connections.
2. Double-click Local Area Connection.
20