Planet GRT-101 User manual

G.SHDSL Bridge Router
GRT-101/GRT-401/GRT-402
Quick Installation Guide

Table of Contents
Chapter 1 Before Starting Up............................................................................ 3
Chapter 2 Quick Installation ............................................................................. 4
2.1 Bridge Mode ............................................................................. 4
2.2 Routing Mode for PPPoA and PPPoE with IP Sharing ..................... 6
2.3 Routing Mode for IPoA or EoA .................................................... 9
2.4 LAN-to-LAN Connection with Bridge Mode...................................13

3
Chapter 1 Before Starting Up
Before proceeding any further, please make sure correct Ethernet cable is used
for connecting the LAN port of your computer to GRT-101/401/402. The LAN LNK
indicator on the front panel will light up if a correct cable is used.
By default, the GRT-101/401/402 is shipped with its DHCP Server function enabled.
This means the client computers on the LAN network including the Administrator
PC can set their TCP/IP settings to automatically obtain an IP address from the
GRT-101/401/402.
■Start your web browser and type http://192.168.0.1 in the browser’s address
box, and wait for the login screen appears. The default user name and pass-
word are “root”. Click OK button and you will login the management of
GRT-101/401/402.
Note
The factory default management IP and subnet mask of GRT-
101/401/402 is 192.168.0.1 and 255.255.255.0 respectively. And
the default user name and password are “root”.
This quick installation guide is intended to help to install the G.SHDSL Bridge
Router to the network through the management interface. For more detailed
settings, please also refer to the user’s manual.

4
Chapter 2 Quick Installation
This chapter provides quick setup procedures for four major connection modes:
Section 2.1: Bridge Mode
Section 2.2: Routing Mode for PPPoA and PPPoE
Section 2.3: Routing Mode for IPoA or EoA
Section 2.4: LAN to LAN Bridge Mode
Please verify your connection mode and check the corresponding section to quickly
install your GRT-101/401/402.
2.1 Bridge Mode
GRT-101
LAN IP 192.168.0.1
Mask 255.255.255.0
PC
IP 192.168.0.31
Mask 255.255.255.0
Gateway 192.168.0.254
VPI = 0, VCI = 32
Encapsulation = LLC
BAS
IP 192.168.0.254
DSLAM
Bridge Mode
ISP
Web UI Conguration
After connection via web browser, click and to set up Bridging
mode of GRT-101/401/402 and then click for the next setting.

5
1. Enter WAN1 VPI: 0and VCI: 32.
2. Select WAN1 AAL5 Encap:
3. Enter LAN IP: 192.168.0.1
4. Enter LAN Sub-net Mask: 255.255.255.0
5. Enter Gateway: 192.168.0.254
The Gateway is directly pointed to the BAS IP.
6. Enter DNS Server : 168.95.1.1 and 168.95.192.1
7. Click
8.The screen will prompt the new congured parameters. Check the parameters
and click . The router will reboot with the new setting or click
tocongureotherparameters.
Console Conguration
Do the following steps:
1. User: admin password: admin 
2. enable supervisor password: root 
3. setup mode Bridge 
4. wan Interface number (1~8): 1 
Protocol : Ethernet 
vpi_vci: 0 
32 
encap: LLC 

6
5. bridge gateway 192.168.0.254 
6. lan Interface number: 1 
7 address 192.168.0.1 
255.255.255.0 
8. (back to root) write y 
y (reboot)
2.2 Routing Mode for PPPoA and PPPoE with IP Sharing
GRT-101
LAN IP 192.168.0.1
Mask 255.255.255.0
PC
IP 192.168.0.2
Mask 255.255.255.0
Gateway 192.168.0.1
DNS 192.168.0.1
VPI = 0, VCI = 32
Encapsulation = LLC
BAS
DSLAM
Router Mode
usrname: user1@net
password: user
ISP
WANLAN
Web UI Conguration
For Route Mode with Point-to-Point Protocol over ATM and Ethernet, follow the
following settings. First select and , and then click for
setting other parameters.

7
1. Enter LAN IP: 192.168.0.1
2. Enter LAN Sub-net Mask: 255.255.255.0
3. Host Name: SOHO
4. DHCP Server: Enable
5. Click
6. Enter DHCP Client Start IP: 192.168.0.2
7. Enter DHCP Client End IP: 192.168.0.51
8. Enter DNS Server: 192.168.0.1
9. The DNS server is embedded in GRT-101/401/402.
10.Click to write the new setting.

8
11.Enter WAN1 VPI: 0and VCI: 32.
12.Select WAN1 AAL5 Encap:
13.Select: or
14.Click
15.Enter User Name provided by ISP: user1@net
16.Enter Password provided by ISP: user1
17.Re-enterPasswordforconrmation:user1
18.The screen will prompt the new congured parameters. Check the param-
eters and click . The router will reboot with the new setting or click
tocongureotherparameters.

9
Console Conguration
Do the following steps:
1. User: admin password: admin 
2. enable supervisor password: root 
3. setup mode Route 
4. wan Interface number (1~8): 1 
protocol PPPoA or PPPoE 
vpi_vci: 0 
32 
encap LLC 
isp account: user1@net 
password: user1 
Idle timeout (ENTER for default) <10>: 10
5. lan Interface number: 1 
6. address 192.168.0.1 
255.255.255.0 
attrib Virtual 
7. (back to root) write y 
y (reboot)
2.3 Routing Mode for IPoA or EoA
LAN IP 192.168.0.1
Mask 255.255.255.0
PC
IP 192.168.0.2
Mask 255.255.255.0
Gateway 192.168.0.1
VPI = 0, VCI = 32
Encapsulation = LLC
BAS
DSLAM
ISP
WANLAN
GRT-101
Router Mode
WNA IP 10.1.2.1
Mask 255.255.255.0
Gateway 10.1.2.2
DNS 168.95.1.1
IP 10.1.2.2
Mask 255.255.255.0

10
Web UI Conguration
For Route Mode with Classical IP over ATM and Ethernet over ATM, follow the
following settings. First select and , and then click for
setting other parameters.
1. Enter LAN IP: 192.168.0.1
2. Enter LAN Sub-net Mask: 255.255.255.0
3. Host Name: SOHO
4. DHCP Server: Enable
5. Click