Planet VIP-280 User manual

Table of Contents
Overview 1
Document Objectives 1
Document Organization 1
Preparation before VIP-280/VIP-320 administration 1
Physical Installation 1
Keypad and button definition on DCT-100 3
Installing Batteries 3
Administration Interface 4
Web configuration access 4
LAN/WAN Interface quick configurations 5
LAN IP address configuration via web configuration interface 5
Parameter Description 5
WAN IP address configuration via web configuration interface 6
Save Modification to Flash Memory 6
Voice communication samples 7
VIP-280 / VIP-320 configurations 7
Machine configurations on the VIP-280/VIP-320 8
Quick reference in CD-ROM guide 10

1
This page is intentionally left blank

1
Overview
This quick installation guide describes the objectives; organization and basic installation
of the PLANET VIP-280/VIP-320 VoIP router, and explains how to establish your rst
voice over IP communication via PLANET product. Also, this guide shows you how to nd
additional information on related products and services.
The VIP-280/VIP-320 integrates a web-based graphical user interface that can cover
most congurations and machine status monitoring. Via standard, web browser, you can
congure and check machine status from anywhere around the world.
Document Objectives
This guide provides physical installation, LAN/WAN IP congurations, and Internet access
estab-lishment information for the PLANET VIP-280/VIP-320 VoIP router.
Document Organization
This guide is organized as follows:
· Preparation before VIP-280/VIP-320 administration
· Administration interface
· LAN/WAN Interface quick configurations
· Internet access setup guide
Preparation before VIP-280/VIP-320 administration
Physical Installation
Front Panel of VIP-280
Rear Panel of VIP-280

2
3
Front Panel of VIP-320
Rear Panel of VIP-320
Overview of DECT handset DCT-100

2
3
Keypad and button denition on DCT-100
Descriptions
INT Intercom conversation mode
Adjust the volume level during the conversation and menu
selection on the LCD display.
Last Number Redial
Hang on / up telephone or pressing until to open /
close speaker
C Cancel and Clear
R Power on / off
Number 0–9
and #
The function is as the same as the general phone set.
* Press * to switch PSTN
Installing Batteries
The three rechargeable Ni-MH batteries (AAA size) come with your phone. Install the
batteries before using your phone.
1. Slide the battery cover in the direction of the arrow and pull it out.
2. Remove old batteries, if any, and insert new batteries as indicated, matching
correct polarity (+, -).
3. Replace the battery cover, slide the cover up until it snaps shut.

4
5
 NOTE:
· This phone won’t work by itself. It should be registered
to the main base unit.
· Before initial using, it should be charged for 24 hours
· Reversing the orientation may damage the handset.
· The battery needs to be replaced if it does not recover its
full storage capacity after recharging.
· When replacing batteries, always use good quality Ni-MH
re-chargeable AAA size batteries.
· Never use other batteries or conventional alkaline bat-
teries.
Administration Interface
PLANET VIP-280/VIP-320 provides GUI (Web based, Graphical User Interface) for
machine management and administration.
Web conguration access:
To start VIP-280/VIP-320 web conguration, you must have one of these web browsers
installed on computer for management
· Netscape Communicator 4.03 or higher
· Microsoft Internet Explorer 4.01 or higher with Java support
Default LAN interface IP address of VIP-280/VIP-320 is 192.168.0.1. You may now open
your web browser, and insert 192.168.0.1 in the address bar of your web browser to logon
VIP-280/VIP-320 web conguration page.
VIP-280/VIP-320 will prompt for logon username/password, please enter: admin / 123
to continue machine administration.

4
5
 NOTE:
Please locate your PC in the same network segment
(192.168.0.x) of VIP-280/320. If you’re not familiar with
TCP/IP, please refer to related chapter on user’s manual CD
or consult your network administrator for proper network
configurations.
LAN/WAN Interface quick congurations
Nature of PLANET VIP-280/VIP-320 is an IP Sharing (NAT) device, it comes with two
default IP addresses, and default LAN side IP address is “192.168.0.1”, default WAN side
IP address is “172.16.0.1”. You may use any PC to connect to the LAN port of VIP-280/
VIP-320 to start machine administration.
Hint:
In general cases, the LAN IP address is the default gateway
of LAN side workstations for Internet access, and the WAN
IP of VIP-280/320 are the IP address for remote calling party
to connect with.
LAN IP address conguration via web conguration interface
Here we’d like to congure the IP address of VIP-110/VIP-210 LAN interface, LAN IP
address related commands are:
LAN IP Address:192.168.0.1
Subnet Mask:255.255.255.0
Default Gateway:192.168.0.254
Parameter Description
IP address LAN IP address of VIP-280/VIP-320
Default: 192.168.0.1
Subnet Mask LAN mask of VIP-280/VIP-320
Default: 255.255.255.0
Default Gateway Gateway of VIP-280/VIP-320
Default: 192.168.0.254
Hint:
It is suggested to keep the DHCP server related parameters
in default state to keep machine in best performance.
After conrming the modication you’ve done, Please click on the Modify button to macke
the changes effective,

6
7
WAN IP address conguration via web conguration interface
Execute your web browser, and insert the IP address (default: 172.16.0.1) of VIP in
the adddress bar. After logging on machine with username/password (default: admin
/ 123), browse to “WAN Setting” conguration menu, you will see the conguration
screen below:
Connection Type Data required.
Obtain IP Address
Automatically
In most circumstances, it is no need to configure the
DHCP set-tings.
Specify an IP
Address
The ISP will assign IP Address, and related information.
PPPoE The ISP will assign PPPoE username / password for In-
ternet access,
Hint:
Please consult your ISP personnel to obtain proper PPPoE/IP
address related information, and input carefully.
If Internet connection cannot be established, please check
the physical connection or contact the ISP service staff for
support information.
Save Modication to Flash Memory
Most of the VoIP Router parameters will take effective after you modify, but it is just
temporary stored on RAM only, it will disappear after your reboot or power off the VoIP
Router, to save the parameters into Flash ROM and let it take effective forever, please
remember to press the Save Modication button after you modify the parameters.

6
7
Voice communication samples
There are several ways to make calls to desired destination in VIP-280/VIP-320. In this
section, we’ll lead you step by step to establish your rst voice communication via keypad
and web browsers operations.
Peer to Peer (P2P) mode
VIP-280 / VIP-320 congurations:
STEP 1:
Please log in machine via web browser, and select Line Setting in the Line cong menu,.
In this Line Setting page, please insert the telephone number assigned to this line, and
then the sample conguration screen is shown below (in this sample, we’re using number
7001 for incoming calls).
STEP 2:
Select VoIP Call Out in the Call Routing menu; insert the values of the index number, Area
Code and IP Address on the VoIP call out routing table for outgoing calls. The sample
conguration screen is shown below.

8
9
Hint:
When the calling party is an H.323 device, please add a
”h323:” in front of the IP address.
Such as: the destination H.323 device is 172.16.0.100, then
input “h323:172.16.0.100” in the IP address column of VIP-
320/VIP-280 VoIP Callout setting page
When the calling party is a SIP device, please add a “sip:” in
front of the IP address.
Such as: the destination SIP device is 172.16.0.200, then
input “sip:172.16.0.200” in the IP address field.
STEP 3:
After the settings for the remote calling party, you may dial number 1001 to connect to
the H.323 IP phone, and number 2001 to connect to the SIP IP phone.
Hint:
If you’re using the VIP-280, you may dial the H.323 and the
SIP calls at the same time.
Machine congurations on the VIP-280/VIP-320:
STEP 1:
Please log in machine via web browser, and select Register Server setting in the VoIP
Cong menu,. In this setting page, please insert the account/password information , and
then the sample conguration screen is shown below (in this sample, we’re using the SIP-
50 as the registration server).