Planet MGSW-28240F User manual

24-Port 100/1000X SFP + 4-Port 10G SFP+
Managed Metro Ethernet Switch
MGSW-28240F
Quick Installation Guide

Table of Contents
1. Package Contents ....................................................................................... 3
2. Requirements ............................................................................................. 4
3. Wiring DC Power Inputs .............................................................................. 5
4. Terminal Setup ........................................................................................... 6
5. Logon to the Console .................................................................................. 7
6. ConguringIPAddress................................................................................ 8
7. Starting Web Management .........................................................................10
8. Customer Support .....................................................................................14

3
1. Package Contents
Thank you for purchasing PLANET Managed Metro Ethernet Switch, MGSW-28240F.
The term “Managed Switch” mentioned in this Quick Installation Guide refers to
theMGSW-28240F.
Open the box of the Managed Switch and carefully unpack it. The box should
contain the following items:
TheMGSW-28240FSwitchx1l
User’s Manual CD x 1l
QuickInstallationGuidex1l
DB9toRJ-45ConsoleCablex1l
Dust Cap x 33l
RubberFeetx4l
RackMountAccessoryKitx1l
ACPowerCordx1l
If any item is found missing or damaged, please contact your local reseller for
replacement.

4
2. Requirements
WorkstationshouldberunningWindowsXP/Vista/7/8,Windows2003/2008,MACl
OSXorlater,Linux,UNIXorotherplatformscompatiblewithTCP/IPprotocols.
WorkstationshouldbeinstalledwithEthernetNIC(NetworkInterfaceCard)l
Serial Port Connectionl(Terminal)
TheaboveworkstationshouldcomewithCOMPort(DB9)
Ethernet Port Connectionl
Networkcables-Usestandardnetwork(UTP)cableswithRJ-45connectors.
The above PC should be installed with WEB Browser and JAVA runtime envi-
ronmentPlug-in.
Note
It is recommended to use Internet Explore 7.0 or above to access
theManagedSwitch.

5
3. Wiring DC Power Inputs
The 6-contact terminal block connector on the rear panel of the MGSW-28240F is
used for two DC redundant power inputs. Please follow the steps below to insert
the power wire.
1.Insert positive / negative DC power wires into the contacts 1 and 2 for DC
POWER1,or5and6forDCPOWER2.
100~240V AC
50/60 Hz
ON
AC POWER
OFF
DC POWER
ON
OFF
Ring R.O.
FaultFAN2
FAN1
PWR
DC 2
DC 1
DC Input Range:
36V~72V Fault
GNDGNDDO 1DO 0DI 1DI 0
DC 2DC 1 1
2.Tightenthewire-clampscrewsforpreventingthewiresfromloosening.
123456
DC 1 Fault
Alarm
DC 2
+-+-
Note
Thewiregaugefortheterminalblockshouldbeintherangeof12
~24AWG.

6
4. Terminal Setup
To congure the system, connect a serial cable to a COM port on a PC or
notebookcomputerandtoserial(console)portoftheManagedSwitch.Theconsole
port of the Managed Switch is DCE already so that you can connect the console
portdirectlythroughthePCwithouttheneedofNullModem.
PC / Workstation
with
Terminal emulation software
Serial Port
PLANET Managed Switch
RS-232
Serial Port
115200,8,n,1
A terminal program is required to make the software connection to the Managed
Switch. Windows' Hyper Terminal program may be a good choice. The Hyper
TerminalcanbeaccessedfromtheStart menu.
1. Click START,thenPrograms,AccessoriesandthenHyper Terminal.
2.When the following screen appears, make sure that the COM port should be
conguredas:
Baud : 115200
Data bits : 8
Parity :None
Stop bits : 1
Flow Control :None

7
5. Logon to the Console
Oncetheterminalhasbeenconnectedtothedevice,powerontheManagedSwitch
andtheterminalwilldisplay“runningtestingprocedures”.
Then, the following message asks for the login username and password. The
factory default username and password are admin as the following and the login
screeninFigure5-1appears.
Username: admin
Password:admin
Figure 5-1: MGSW-28240F Managed Switch Console Login Screen
Note
1.For security reason, please change and memorize the new pass-
wordafterthisfirstsetup.
2.Only accept command in lowercase letter under console inter-
face.

8
6.ConguringIPAddress
TheManagedSwitchisshippedwithdefaultIPaddressasshownbelow:.
IPAddress:192.168.0.100
Subnet Mask: 255.255.255.0
TocheckthecurrentIPaddressormodifyanewIPaddressfortheSwitch,please
usetheproceduresasfollows:
Show the current IP address
1. On “MGSW-28240F/>”prompt,enter“show ip”.
2.ThescreendisplaysthecurrentIPaddress,SubnetMaskandGatewayasshown
inFigure6-1.
Figure 6-1: Show IP Information Screen

9
 ConguringIPaddress
3. On “MGSW-28240F/>” prompt, enter the following command and press
<Enter>asshowninFigure6-2.
MGSW-28240F/> ip setup 192.168.1.100 255.255.255.0 192.168.1.1
ThepreviouscommandwouldapplythefollowsettingsfortheSwitch.
IP Address: 192.168.1.100
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.1
Figure 6-2: Set IP Address Screen
4.RepeatStep1tocheckiftheIPaddressischanged.
If the IP is successfully congured, the Managed Switch will apply the new IP
address setting immediately. You can access the Web interface of the Managed
SwitchthroughthenewIPaddress.
Note
Ifyouarenotfamiliarwithconsolecommandortherelatedparam-
eter,enter“help”anytimeinconsoletogetthehelpdescription.

10
7. Starting Web Management
The following shows how to start up the Web Management of the Managed
Switch. Note the Managed Switch is congured through an Ethernet connection.
Please make sure the manager PC must be set on the same IP subnet address.
For example, the default IP address of the Managed Switch is 192.168.0.100,
thenthemanagerPCshouldbesetat192.168.0.x(wherexisanumberbetween
1and254,except100),andthedefaultsubnetmaskis255.255.255.0.
IP Address:
192.168.0.100
PLANET Managed Switch
PC / Workstation
with
IE Browser
IP Address :
192.168.0.x RJ-45 / UTP Cable
Figure 7-1: IP Management Diagram
Login the Managed Switch
1.Use Internet Explorer 7.0 or above Web browser and enter IP address
http://192.168.0.100 (the factory-default IP address or that you have just
changedinconsole)toaccesstheWebinterface.