Planet PL-802 User manual

– 6 – – 7 –
Step 2: To secure your powerline network:
1. Press and hold the Security button of PL-802 for 10
seconds. Then all the LEDs are off and restart. The
original network encryption setting is cleared.
2. Repeat 1 to clear another powerline’s original network
encryption setting.
3. Press the Security buttons of both powerlines for 1 to
3 seconds.
4. The power LED of both powerlines starts to blink
and try to communicate with their private network
encryption.
Note: The operation timeout is 120 seconds.
5. After the successful setup, the Power LED will
remain solid and the Powerline LED will start
blinking.
Push
Button
Within 2 minutes
Step 3: 1. Connect the Ethernet port of PL-802 to your home
router, switch or ADSL modem’s Ethernet port via the
RJ45 cable.
2. Connect the Ethernet port of the PL-802 to the
computer via the RJ45 cable.
Linked
Internet
Laptop
6. Utility Installation for Windows
PLANET Power Packet Utility is a software utility used to search and
make connecting on a powerline network quick and simple.
The installation procedure for the Powe Packet Utility will vary
depending on which operating system you are using on your computer.
The following procedure is for installation under Windows 7. Installation
of other operating systems is similar.
Step 1: Download the Power Packet Utility from PLANET download
URL
http://www.planet.com.tw/en/support/download.
php?view=8184&key=PL-802#list
Step 2: The le you have downloaded is a zip le. Unzip it and
double-click on the “Setup.exe” executable le to begin
installation.
Step 3: The utility will be installed on your computer and
a new icon “Power Packet Utility” will appear
on your desktop.
Power Packet
Utility
Note
This utility is only for Windows 2000, 2003, XP, Vista,
Windows 7, Windows 8 and Windows 10.
Further Information:
The above steps introduce the simple installations of the PL-802. For
further details on the installation of the powerline, please refer to the
user manual which can be downloaded from the PLANET website.
http://www.planet.com.tw/en/support/download.
php?view=3&key=PL-802#list
If you have further questions, please contact the local dealer or
distributor where you purchased this product or you can contact PLANET
directly at the following email address: [e-mail]
– 5 –

– 1 –
– 3 –
– 2 –
– 4 –
3. Physical Introduction
Port & Button Descriptions
Security Button
10/100BASE-TX
Ethernet RJ-45 Port
Button Description
Security
Reset: Hold the Security button down for 10 seconds to
reset to default setting. All of the LED lights will
go out 1 second and then light up again.
Pair: Press the Security button for 1~3 seconds to join
another powerline network. The power LED will ash
to search another powerline.
1. Package Contents
Thank you for choosing PLANET 600M AV2 Powerline Ethernet Bridge,
PL-802/PL-802-KIT. Open the box of the PL-802/PL-802-KIT carefully and
unpack it. The box should contain the following items:
PL-802
(Twin pack x 2) Quick Install Guide Ethernet Cable (Twin pack x 2)
Note
If there is any item missing or damaged, please contact
the seller immediately.
2. Installation Precautions
Do not plug this powerline adapter into a powerstrip that has surge
protection. Doing so will degrade powerline performance. For best
performance, plug all powerline adapters directly into a wall outlet.
Good Performance Weak Performance
A maximum of 16 powerline adapters can be networked.
LED Descriptions
Ethernet LED
Power LED
Powerline LED
LED Denition
LED Status Description
Power
Green Steady on to indicate the PL-802 is connected to
the power outlet.
Blinking Standby mode.
Off Power off.
Powerline
Off This powerline adapter is not connected.
Green The quality of signal is excellent with optimal
network.
Orange The quality of signal is normal with standard
network.
Red The quality of signal is weak which causes slower
network.
Blinking
Green
The PL-802 is actively sending or receiving data
with another powerline.
Ethernet
Green Ethernet Link detected
Blinking The PL-802 is actively sending or receiving data
over the Ethernet port.
Off Ethernet Link not active.
Note
The Power LED indicator will blink in standby mode.
It will automatically get into standby mode, if the
Ethernet-link is lost for 60 seconds. If you unplug the
Ethernet cable, it will get into standby mode after 60
seconds. Under standby mode, Powerline and
Ethernet LEDs will both be off.
4. Hardware Installation
To create a powerline network, simply connect the PL-802 and the
Powerline Ethernet Bridge to AC wall power outlets that are on the
same electrical system. No additional conguration in the powerline
network is necessary.
Follow the steps below to install the PL-802 in the house.
Step 1: 1. Plug the Powerline Ethernet Bridge into AC wall
power outlets near the device you want to connect.
2. Plug the PL-802 into AC wall power outlet in your room
or ofce where you want to install.
3. Ensure the Power LEDs are on.
Plug
in

– 1 –
– 3 –
– 2 –
– 4 –
3. Physical Introduction
Port & Button Descriptions
Security Button
10/100BASE-TX
Ethernet RJ-45 Port
Button Description
Security
Reset: Hold the Security button down for 10 seconds to
reset to default setting. All of the LED lights will
go out 1 second and then light up again.
Pair: Press the Security button for 1~3 seconds to join
another powerline network. The power LED will ash
to search another powerline.
1. Package Contents
Thank you for choosing PLANET 600M AV2 Powerline Ethernet Bridge,
PL-802/PL-802-KIT. Open the box of the PL-802/PL-802-KIT carefully and
unpack it. The box should contain the following items:
PL-802
(Twin pack x 2) Quick Install Guide Ethernet Cable (Twin pack x 2)
Note
If there is any item missing or damaged, please contact
the seller immediately.
2. Installation Precautions
Do not plug this powerline adapter into a powerstrip that has surge
protection. Doing so will degrade powerline performance. For best
performance, plug all powerline adapters directly into a wall outlet.
Good Performance Weak Performance
A maximum of 16 powerline adapters can be networked.
LED Descriptions
Ethernet LED
Power LED
Powerline LED
LED Denition
LED Status Description
Power
Green Steady on to indicate the PL-802 is connected to
the power outlet.
Blinking Standby mode.
Off Power off.
Powerline
Off This powerline adapter is not connected.
Green The quality of signal is excellent with optimal
network.
Orange The quality of signal is normal with standard
network.
Red The quality of signal is weak which causes slower
network.
Blinking
Green
The PL-802 is actively sending or receiving data
with another powerline.
Ethernet
Green Ethernet Link detected
Blinking The PL-802 is actively sending or receiving data
over the Ethernet port.
Off Ethernet Link not active.
Note
The Power LED indicator will blink in standby mode.
It will automatically get into standby mode, if the
Ethernet-link is lost for 60 seconds. If you unplug the
Ethernet cable, it will get into standby mode after 60
seconds. Under standby mode, Powerline and
Ethernet LEDs will both be off.
4. Hardware Installation
To create a powerline network, simply connect the PL-802 and the
Powerline Ethernet Bridge to AC wall power outlets that are on the
same electrical system. No additional conguration in the powerline
network is necessary.
Follow the steps below to install the PL-802 in the house.
Step 1: 1. Plug the Powerline Ethernet Bridge into AC wall
power outlets near the device you want to connect.
2. Plug the PL-802 into AC wall power outlet in your room
or ofce where you want to install.
3. Ensure the Power LEDs are on.
Plug
in

– 1 –
– 3 –
– 2 –
– 4 –
3. Physical Introduction
Port & Button Descriptions
Security Button
10/100BASE-TX
Ethernet RJ-45 Port
Button Description
Security
Reset: Hold the Security button down for 10 seconds to
reset to default setting. All of the LED lights will
go out 1 second and then light up again.
Pair: Press the Security button for 1~3 seconds to join
another powerline network. The power LED will ash
to search another powerline.
1. Package Contents
Thank you for choosing PLANET 600M AV2 Powerline Ethernet Bridge,
PL-802/PL-802-KIT. Open the box of the PL-802/PL-802-KIT carefully and
unpack it. The box should contain the following items:
PL-802
(Twin pack x 2) Quick Install Guide Ethernet Cable (Twin pack x 2)
Note
If there is any item missing or damaged, please contact
the seller immediately.
2. Installation Precautions
Do not plug this powerline adapter into a powerstrip that has surge
protection. Doing so will degrade powerline performance. For best
performance, plug all powerline adapters directly into a wall outlet.
Good Performance Weak Performance
A maximum of 16 powerline adapters can be networked.
LED Descriptions
Ethernet LED
Power LED
Powerline LED
LED Denition
LED Status Description
Power
Green Steady on to indicate the PL-802 is connected to
the power outlet.
Blinking Standby mode.
Off Power off.
Powerline
Off This powerline adapter is not connected.
Green The quality of signal is excellent with optimal
network.
Orange The quality of signal is normal with standard
network.
Red The quality of signal is weak which causes slower
network.
Blinking
Green
The PL-802 is actively sending or receiving data
with another powerline.
Ethernet
Green Ethernet Link detected
Blinking The PL-802 is actively sending or receiving data
over the Ethernet port.
Off Ethernet Link not active.
Note
The Power LED indicator will blink in standby mode.
It will automatically get into standby mode, if the
Ethernet-link is lost for 60 seconds. If you unplug the
Ethernet cable, it will get into standby mode after 60
seconds. Under standby mode, Powerline and
Ethernet LEDs will both be off.
4. Hardware Installation
To create a powerline network, simply connect the PL-802 and the
Powerline Ethernet Bridge to AC wall power outlets that are on the
same electrical system. No additional conguration in the powerline
network is necessary.
Follow the steps below to install the PL-802 in the house.
Step 1: 1. Plug the Powerline Ethernet Bridge into AC wall
power outlets near the device you want to connect.
2. Plug the PL-802 into AC wall power outlet in your room
or ofce where you want to install.
3. Ensure the Power LEDs are on.
Plug
in

– 1 –
– 3 –
– 2 –
– 4 –
3. Physical Introduction
Port & Button Descriptions
Security Button
10/100BASE-TX
Ethernet RJ-45 Port
Button Description
Security
Reset: Hold the Security button down for 10 seconds to
reset to default setting. All of the LED lights will
go out 1 second and then light up again.
Pair: Press the Security button for 1~3 seconds to join
another powerline network. The power LED will ash
to search another powerline.
1. Package Contents
Thank you for choosing PLANET 600M AV2 Powerline Ethernet Bridge,
PL-802/PL-802-KIT. Open the box of the PL-802/PL-802-KIT carefully and
unpack it. The box should contain the following items:
PL-802
(Twin pack x 2) Quick Install Guide Ethernet Cable (Twin pack x 2)
Note
If there is any item missing or damaged, please contact
the seller immediately.
2. Installation Precautions
Do not plug this powerline adapter into a powerstrip that has surge
protection. Doing so will degrade powerline performance. For best
performance, plug all powerline adapters directly into a wall outlet.
Good Performance Weak Performance
A maximum of 16 powerline adapters can be networked.
LED Descriptions
Ethernet LED
Power LED
Powerline LED
LED Denition
LED Status Description
Power
Green Steady on to indicate the PL-802 is connected to
the power outlet.
Blinking Standby mode.
Off Power off.
Powerline
Off This powerline adapter is not connected.
Green The quality of signal is excellent with optimal
network.
Orange The quality of signal is normal with standard
network.
Red The quality of signal is weak which causes slower
network.
Blinking
Green
The PL-802 is actively sending or receiving data
with another powerline.
Ethernet
Green Ethernet Link detected
Blinking The PL-802 is actively sending or receiving data
over the Ethernet port.
Off Ethernet Link not active.
Note
The Power LED indicator will blink in standby mode.
It will automatically get into standby mode, if the
Ethernet-link is lost for 60 seconds. If you unplug the
Ethernet cable, it will get into standby mode after 60
seconds. Under standby mode, Powerline and
Ethernet LEDs will both be off.
4. Hardware Installation
To create a powerline network, simply connect the PL-802 and the
Powerline Ethernet Bridge to AC wall power outlets that are on the
same electrical system. No additional conguration in the powerline
network is necessary.
Follow the steps below to install the PL-802 in the house.
Step 1: 1. Plug the Powerline Ethernet Bridge into AC wall
power outlets near the device you want to connect.
2. Plug the PL-802 into AC wall power outlet in your room
or ofce where you want to install.
3. Ensure the Power LEDs are on.
Plug
in

– 6 – – 7 –
Step 2: To secure your powerline network:
1. Press and hold the Security button of PL-802 for 10
seconds. Then all the LEDs are off and restart. The
original network encryption setting is cleared.
2. Repeat 1 to clear another powerline’s original network
encryption setting.
3. Press the Security buttons of both powerlines for 1 to
3 seconds.
4. The power LED of both powerlines starts to blink
and try to communicate with their private network
encryption.
Note: The operation timeout is 120 seconds.
5. After the successful setup, the Power LED will
remain solid and the Powerline LED will start
blinking.
Push
Button
Within 2 minutes
Step 3: 1. Connect the Ethernet port of PL-802 to your home
router, switch or ADSL modem’s Ethernet port via the
RJ45 cable.
2. Connect the Ethernet port of the PL-802 to the
computer via the RJ45 cable.
Linked
Internet
Laptop
6. Utility Installation for Windows
PLANET Power Packet Utility is a software utility used to search and
make connecting on a powerline network quick and simple.
The installation procedure for the Powe Packet Utility will vary
depending on which operating system you are using on your computer.
The following procedure is for installation under Windows 7. Installation
of other operating systems is similar.
Step 1: Download the Power Packet Utility from PLANET download
URL
http://www.planet.com.tw/en/support/download.
php?view=8184&key=PL-802#list
Step 2: The le you have downloaded is a zip le. Unzip it and
double-click on the “Setup.exe” executable le to begin
installation.
Step 3: The utility will be installed on your computer and
a new icon “Power Packet Utility” will appear
on your desktop.
Power Packet
Utility
Note
This utility is only for Windows 2000, 2003, XP, Vista,
Windows 7, Windows 8 and Windows 10.
Further Information:
The above steps introduce the simple installations of the PL-802. For
further details on the installation of the powerline, please refer to the
user manual which can be downloaded from the PLANET website.
http://www.planet.com.tw/en/support/download.
php?view=3&key=PL-802#list
If you have further questions, please contact the local dealer or
distributor where you purchased this product or you can contact PLANET
directly at the following email address: [e-mail]
– 5 –

– 6 – – 7 –
Step 2: To secure your powerline network:
1. Press and hold the Security button of PL-802 for 10
seconds. Then all the LEDs are off and restart. The
original network encryption setting is cleared.
2. Repeat 1 to clear another powerline’s original network
encryption setting.
3. Press the Security buttons of both powerlines for 1 to
3 seconds.
4. The power LED of both powerlines starts to blink
and try to communicate with their private network
encryption.
Note: The operation timeout is 120 seconds.
5. After the successful setup, the Power LED will
remain solid and the Powerline LED will start
blinking.
Push
Button
Within 2 minutes
Step 3: 1. Connect the Ethernet port of PL-802 to your home
router, switch or ADSL modem’s Ethernet port via the
RJ45 cable.
2. Connect the Ethernet port of the PL-802 to the
computer via the RJ45 cable.
Linked
Internet
Laptop
6. Utility Installation for Windows
PLANET Power Packet Utility is a software utility used to search and
make connecting on a powerline network quick and simple.
The installation procedure for the Powe Packet Utility will vary
depending on which operating system you are using on your computer.
The following procedure is for installation under Windows 7. Installation
of other operating systems is similar.
Step 1: Download the Power Packet Utility from PLANET download
URL
http://www.planet.com.tw/en/support/download.
php?view=8184&key=PL-802#list
Step 2: The le you have downloaded is a zip le. Unzip it and
double-click on the “Setup.exe” executable le to begin
installation.
Step 3: The utility will be installed on your computer and
a new icon “Power Packet Utility” will appear
on your desktop.
Power Packet
Utility
Note
This utility is only for Windows 2000, 2003, XP, Vista,
Windows 7, Windows 8 and Windows 10.
Further Information:
The above steps introduce the simple installations of the PL-802. For
further details on the installation of the powerline, please refer to the
user manual which can be downloaded from the PLANET website.
http://www.planet.com.tw/en/support/download.
php?view=3&key=PL-802#list
If you have further questions, please contact the local dealer or
distributor where you purchased this product or you can contact PLANET
directly at the following email address: [e-mail]
– 5 –

– 6 – – 7 –
Step 2: To secure your powerline network:
1. Press and hold the Security button of PL-802 for 10
seconds. Then all the LEDs are off and restart. The
original network encryption setting is cleared.
2. Repeat 1 to clear another powerline’s original network
encryption setting.
3. Press the Security buttons of both powerlines for 1 to
3 seconds.
4. The power LED of both powerlines starts to blink
and try to communicate with their private network
encryption.
Note: The operation timeout is 120 seconds.
5. After the successful setup, the Power LED will
remain solid and the Powerline LED will start
blinking.
Push
Button
Within 2 minutes
Step 3: 1. Connect the Ethernet port of PL-802 to your home
router, switch or ADSL modem’s Ethernet port via the
RJ45 cable.
2. Connect the Ethernet port of the PL-802 to the
computer via the RJ45 cable.
Linked
Internet
Laptop
6. Utility Installation for Windows
PLANET Power Packet Utility is a software utility used to search and
make connecting on a powerline network quick and simple.
The installation procedure for the Powe Packet Utility will vary
depending on which operating system you are using on your computer.
The following procedure is for installation under Windows 7. Installation
of other operating systems is similar.
Step 1: Download the Power Packet Utility from PLANET download
URL
http://www.planet.com.tw/en/support/download.
php?view=8184&key=PL-802#list
Step 2: The le you have downloaded is a zip le. Unzip it and
double-click on the “Setup.exe” executable le to begin
installation.
Step 3: The utility will be installed on your computer and
a new icon “Power Packet Utility” will appear
on your desktop.
Power Packet
Utility
Note
This utility is only for Windows 2000, 2003, XP, Vista,
Windows 7, Windows 8 and Windows 10.
Further Information:
The above steps introduce the simple installations of the PL-802. For
further details on the installation of the powerline, please refer to the
user manual which can be downloaded from the PLANET website.
http://www.planet.com.tw/en/support/download.
php?view=3&key=PL-802#list
If you have further questions, please contact the local dealer or
distributor where you purchased this product or you can contact PLANET
directly at the following email address: [email protected]
– 5 –