Planet ISW-500T User manual

Industrial 5-/8-Port 10/100TX
Compact Ethernet Switch
ISW-500T/ISW-800T
User’s Manual

Table of Contents
1. Package Contents ............................................................. 3
2. Product Features............................................................... 4
3.ProductSpecications ....................................................... 5
4. Hardware Introduction ...................................................... 7
4.1 Three-View Diagram................................................... 7
4.2 Wiring the Power Inputs ........................................... 10
4.3 Wiring the Fault Alarm Contact.................................. 11
5. Installation..................................................................... 13
5.1 DIN-rail Mounting Installation.................................... 13
5.2 Wall-mount Plate Mounting ....................................... 15
Customer Support............................................................... 16

3
1.Package Contents
Thank you for purchasing PLANET industrial 5-/8-port 10/100TX
Compact Ethernet Switch, ISW-500T/800T. In the following
section, the term “Industrial Ethernet Switch” means the
ISW-500T or ISW-800T.
Open the box of the Industrial Ethernet Switch and carefully
unpack it. The box should contain the following items:
Industrial Ethernet Switch x 1 User’s Manual x 1
Wall-mount Kit DIN Rail Kit
If any of these are missing or damaged, please contact your
dealer immediately; if possible, retain the carton including the
original packing material, and use them again to repack the
product in case there is a need to return it to us for repair.

4
2.Product Features
Physical Port
5-port 10/100BASE-TX RJ45 with auto MDI/MDI-X function
(ISW-500T)
8-port 10/100BASE-TX RJ45 with auto MDI/MDI-X function
(ISW-800T)
Layer 2 Features
Complies with IEEE 802.3 10BASE-T, IEEE 802.3u
100BASE-TX Ethernet standard
Supports auto-negotiation and 10/100Mbps half/full duplex
mode
Prevents packet loss with back pressure (half-duplex) and
IEEE802.3x pauseframeowcontrol(full-duplex)
Complieswith IEEE802.3azEnergyEfcientEthernet(EEE)
IEEE 802.1p CoS
Supports 1K MAC address
Automatic address learning and address aging
Industial Case & Installation
IP30 metal case
DIN rail and wall-mount design
12 to 48V DC, redundant power with polarity reverse
protect function
24V AC power input acceptable
Supports 6000 VDC Ethernet ESD protection
-40 to 75 degrees C operating temperature
Free fall, shock-proof and vibration-proof for industries

5
3.ProductSpecications
Product ISW-500T ISW-800T
HardwareSpecications
Copper Ports
5 10/100BASE-TX
RJ45 auto-MDI/MDI-X
ports
8 10/100BASE-TX
RJ45 auto-MDI/MDI-X
ports
Switch Architecture Store-and-Forward
Switch Fabric 1Gbps (non-blocking) 1.6Gbps
(non-blocking)
Throughput
(packet per second) 0.74Mpps@ 64 bytes 1.19Mpps@ 64 bytes
Address Table 1K entries, automatic source address
learning and aging
Shared Data Buffer 448K bits
Flow Control IEEE 802.3x pause frame for full-duplex
Back pressure for half-duplex
ESD Protection 6KV DC
Enclosure IP30 metal case
Installation DIN rail kit and wall-mount kit
Connector
Removable 6-pin terminal block for power
input
Pin 1/2 for Power 1, Pin 3/4 for fault alarm,
Pin 5/6 for Power 2
Alarm One relay output for power failure. Alarm
relay current carry ability: 1A @ 24V DC
LED Indicator
System:
Power 1 (Green) Power 2 (Green)
Fault Alarm (Red)

6
LED Indicator Per 10/100TX RJ45 Ports:
10/100 LNK/ACT (Green)
Dimensions
(W x D x H) 70 x 104 x 30 mm 70 x 115 x 41 mm
Weight 255g 300g
Power Requirements Dual 12~48V DC, 24V AC
Power Consumption Max. 2 watts/6.86BTU
(Ethernet full loading)
Max. 2.5
watts/8.57BTU
(Ethernet full loading)
Standards Conformance
Regulatory
Compliance FCC Part 15 Class A, CE
Stability Testing
IEC60068-2-32 (free fall)
IEC60068-2-27 (shock)
IEC60068-2-6 (vibration)
Standards
Compliance
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX/100BASE-FX
IEEE802.3x owcontrolandbackpressure
IEEE 802.1p Class of Service
IEEE802.3az EnergyEfcientEthernet(EEE)
Environment
Operating
Temperature -40 ~ 75 degrees C
Storage Temperature -40 ~ 85 degrees C
Humidity 5 ~ 95% (non-condensing)

7
4.Hardware Introduction
4.1 Three-View Diagram
The three-view diagram of the Industrial Ethernet Switch
consists of ve or eight auto-sensing 10/100/BASE-TX RJ45
port and one removable 6-pin terminal block. The LED
indicators are also located on the front panel.
18.00
9.00
91.00
52.00 52.00
104.00
30.00
50.00
30.00
70.00
21.69
28.65
Dimensions ( unit = mm )
Side View Front View Side View
Top View
Bottom View
Rear View
P1 P2 FAULT
ACT
LNK
10/100
1 2 3 4 5
ISW-500T
Input DC12~48V, AC 24V
V1+ 1A@24VV1-
DC1
V2+ V2-
DC2
Fault
Figure 1: ISW-500T Three-View Diagram

8
115.00
41.00
70.00
18.00
3.50
103.00
5.50
30.00
50.00
28.65
27.19
Dimensions ( unit = mm )
Side View Front View Side View
Top View
Bottom View
Rear View
P1 P2 FAULT
ACTLNK
10/100
1 2 3 4 5 6 7 8
ISW-800T
Input DC12~48V, AC 24V
V1+ 1A@24VV1-
DC1
V2+ V2-
DC2
Fault
Figure 2: ISW-800T Three-View Diagram

9
Front View
P1 P2 FAULT
ACT
LNK
10/100
1
2
3
4
5
ISW-500T
P1 P2 FAULT
ACTLNK
10/100
1
2
3
4
5
6
7
8
ISW-800T
Figure 1: ISW-500T Front View Figure 2: ISW-800T Front View
LED Denition:
System
LED Color Function
DC1 Green Lights to indicate DC power input 1 has power.
DC2 Green Lights to indicate DC power input 2 has power.
Fault Red Lights to indicate that AC or DC power has failed.
Per 10/100BASE-TX Port
LED Color Function
10/100
LNK/
ACT
Green
Lights Indicating the port is running at 10/100Mbps
speed and successfully established.
Blinks Indicating that the switch is actively sending
or receiving data over that port.

10
Top View
Input
DC12~48V, AC 24V
V1+ 1A@24VV1-
DC1
V2+ V2-
DC2
Fault
1 2 3 4 5 6
Figure 1: ISW-500T Top View
Input
DC12~48V, AC 24V
V1+ 1A@24VV1-
DC1
V2+ V2-
DC2
Fault
1 2 3 4 5 6
Figure 2: ISW-800T Top View
4.2 Wiring the Power Inputs
The 6-contact terminal block connector on the top panel of
Industrial Ethernet Switch is used for two DC redundant power
inputs. Please follow the steps below to insert the power wire.
When performing any of the procedures like
inserting the wires or tightening the wire-clamp
screws, make sure the power is OFF to prevent
from getting an electric shock.