Planet DRV-460 User manual

1
Overview
This quick installation guide describes the objectives, organization
and basic installation of the PLANET DVR-460/DVR-860 surveillance
system, and offers stand-alone system to build a distributed
surveillance system, which can be monitored over the Internet, and
equipped with Hard Disc Drive that records the video directly. Also,
this guide shows you how to nd additional information on related
products and services.
Package Content
DVR-460 / DVR-860
Power Adapter
User’s Manual CD
Quick Installation Guide
Screws
DSUB PIN Connector
IR Receiver
Remote Controller
Flat Cable Clamp
NOTE: If any of the above items are missing or damaged,
contact your local dealer for support.

2
DVR-460 Installation
InstallingHDD
1. Loosen the screws on the upper cover and open the upper cover
of the DVR.
2. Screw out the HDD bracket. For the positions of the HDD bracket
screws, please refer to the figure below.
3. When install the first HDD, please set the jumper on the HDD to
“Master” mode.
4. Screw HDD onto the HDD bracket, two screws for each side.
And then screw the HDD bracket back to the DVR base. (Refer
to Fig.1 & 2).

3
5. Connect the HDD to the power connector and IDE BUS (make
sure to align the HDD precisely for pin connection) (Refer to Fig.
3)
6. Close the upper cover of the DVR and fasten all the screws you
loosened in the step 1. (Refer to Fig. 4 & 5)
NOTE: ONLY use the power adapter supplied with DVR-
460. Otherwise, the product may be damaged.
HardwareInstallation
USB
INP UT
DC 19V
VD /
1
LOOP
EXTERNAL I/OIR
INP U T
2
LOOP LOOP LOOP
3
INP U T
4
INP UT
LAN
ACT .
LINK
1
CA LL
MO NIT OR
IN OUT
1. Please connect your cameras to the Video Input (1~4).
2. Connect your monitor to “Monitor” connector.
3. Connect the LAN port to your switch/hub with a RJ-45 cable.
4. Connect IR reciver to the “IR” connector.
5. Connect the bundle power to the power connector (DC 19V).
6. Press this button to turn on your DVR-460.

4
DVR-860 Installation
InstallingHDD
1. Loosen the screws and open the upper cover.
2. When install the first HDD, please set the jumper on the HDD to
“Master” mode.

5
3. Screw out the HDD bracket from DVR. (Step 1~2)
4. Screw HDD onto the HDD bracket, there is two screws for each
side. And then screw the HDD bracket back to the DVR base.
(Step 3 ~ 8)
5. Connect the power connector and IDE BUS of DVR to installed
HDD. Please make sure to align the HDD precisely for pin con-
nection. (Step 9 ~14)
6. Close the upper cover of the DVR and fasten all the screws that
you loosened in the step 1.
HardwareInstallation
1. Please connect your cameras to the Video Input port 1~8.
2. Connect your monitor to “Monitor” connector.
3. Connect the LAN port to your switch/hub with a RJ-45 cable.
4. Connect IR reciver to the “IR” connector.
5. Connect the bundle power adapter to the power connector.
6. Press the “Power” button (which is located on the front panel) to
turn on your DVR-860.
NOTE: ONLY use the power adapter supplied with DVR-
860. Otherwise, the product may be damaged.

6
Further Conguration
If you want to configure DVR-460/DVR860 and know the further
operation, please refer to our manual in the CD disk. If you have any
difficulty on resolving the problem while installing or using DVR-460/
DVR-860, please feel free to contact PLANET for support.

This page is intentionally left blank

This page is intentionally left blank

Part NO: 2011-AB3740-000