Planet SGS-6341-24T4X User manual

L3 Multi-Port Full Gigabit Stackable Managed Switch
SGS-6341-24T4X/SGS-6341-24P4X/
SGS-6341-48T4X/SGS-6341-16S8C4XR
Quick Installation Guide

Table of Contents
1. Package Contents ....................................................................................... 3
2. Switch Management.................................................................................... 4
3. Requirements ............................................................................................. 5
4. Terminal Setup ........................................................................................... 6
4.1 Logon to the Console........................................................................... 7
4.2 ConguringIPAddress......................................................................... 7
4.3 Setting1000BASE-XforSFP+Port........................................................ 9
4.4 SavingtheConguration ...................................................................... 9
5. Starting Web Management .........................................................................10
5.1LoggingintotheManagedSwitch.........................................................11
5.2SavingCongurationviatheWeb..........................................................13
6. RecoveringBacktoDefaultConguration.....................................................14
7. Customer Support .....................................................................................16

3
1. Package Contents
Thank you for purchasing PLANET L3 Multi-Port Full Gigabit Stackable Managed
Switch, SGS-6341-24T4X/SGS-6341-24P4X/SGS-6341-48T4X/SGS-6341-16S8C4XR.
Thedescriptionsofthesemodelsareasfollows:
SGS-6341-24T4X Layer324-Port10/100/1000T+4-Port10GSFP+
StackableManagedSwitch
SGS-6341-24P4X Layer324-Port10/100/1000T802.3atPoE+4-Port
10GSFP+StackableManagedSwitch(370W)
SGS-6341-48T4X Layer348-Port10/100/1000T+4-Port10GSFP+
StackableManagedSwitch
SGS-6341-16S8C4XR
Layer316-Port100/1000XSFP+8-PortGigabitTP/
SFP+4-Port10GSFP+StackableManagedSwitch
(100~240VAC,12VDC)
Unless specied, “Managed Switch” mentioned in this Quick Installation Guide
referstotheabovethreemodels.
Open the box of the Managed Switch and carefully unpack it. The box should
containthefollowingitems:
zTheManagedSwitchx1
zQuickInstallationGuidex1
zRJ45-to-DB9ConsoleCablex1
zPowerCordx1
zGroundingCablex1
zRubberFeetx4
zTwoRack-mountingBracketswithAttachmentScrewsx1
zSFPDustCap
Model SFPDust-proofCaps
SGS-6341-24T4X 4
SGS-6341-24P4X 8
SGS-6341-48T4X 4
SGS-6341-16S8C4XR 28
If any item is found missing or damaged, please contact your local reseller for
replacement.

4
2. Switch Management
To set up the Managed Switch, the user needs to congure the Managed Switch
fornetwork management.The ManagedSwitch providestwo managementoptions:
Out-of-Band Management and In-Band Management.
Out-of-Band Management
Out-of-band management is the management through Console interface.
Generally, the user will use out-of-band management for the initial switch
conguration,orwhenin-bandmanagementisnotavailable.
Important
TheManagedSwitchisshippedwithIPaddress(192.168.0.254/24)
assigned by default. User can assign another IP address to the
Managed Switch via the Console interface to be able to remotely
accesstheManagedSwitchthroughTelnetorHTTP.
In-Band Management
In-band management refers to the management by logging in to the Managed
Switchusing Telnetor HTTP, orusing SNMPmanagement softwaretocongure the
Managed Switch. In-band management enables the management of the Managed
SwitchtoattachsomedevicestotheSwitch.Thefollowing proceduresarerequired
toenableIn-bandmanagement:
1. Logon to console
2.Assign/CongureIPaddress
3. Create a remote login account
4.EnableHTTPorTelnetserverontheManagedSwitch
In case in-band management fails due to Managed Switch conguration changes,
out-of-band management can be used for conguring and managing the Managed
Switch

5
3. Requirements
zWorkstations running Windows XP/2003/Vista/7/8/2008/10, MAC OS X or later,
Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPprotocols.
zWorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard)
zSerial Port Connection(Terminal)
 The above Workstations come with COM Port (DB9) or USB-to-RS232
converter.
 The above Workstations have been installed with terminal emulator, such as
Tera Term or PuTTY.
 Serial cable -- one end is attached to the RS232 serial port, while the other
endtotheconsoleportoftheManagedSwitch.
zEthernet Port Connection
 Networkcables--Usestandardnetwork(UTP)cableswithRJ45connectors.
 The above PC is installed with Web browser and JAVA runtime environment
plug-in.
Note
It is recommended to use Internet Explore 8.0 or above to access
the Managed Switch. If the Web interface of the Managed Switch
is not accessible, please turn off the anti-virus software or firewall
andthentryitagain.

6
4. Terminal Setup
To congure the system, connect a serial cable to a COM port on a PC or
notebook computer and to serial (console) port of the Managed Switch. The
console port of the Managed Switch is DCE already, so that you can connect the
consoleportdirectlythroughPCwithouttheneedofNullModem.
Managed Switch
PC / Workstation
with
Terminal Emulation Software
Serial Port
RS232 to RJ45 Cable
Console Port
RJ45
Figure 4-1 Managed Switch Console Connectivity
A terminal program is required to make the software connection to the Managed
Switch. Tera Term program may be a good choice. The Tera Term can be accessed
fromtheStart menu.
1. Click START menu, then Programs,andthenTera Term.
2.When the following screen appears, make sure that the COM port should be
conguredas:
zBaud:115200
zParity:None
zDatabits:8
zStopbits:1
zFlowcontrol:None
Figure 4-2 Tera Term COM Port Conguration

7
4.1 Logon to the Console
Once the terminal is connected to the device, power on the Managed  Switch, and
theterminalwilldisplay“running testing procedures”.
Then, the following message asks for the login user name and password. The
factory default user name and password are as follows as the login screen in
Figure4-3appears.
Username:admin
Password:admin
Figure 4-3 Managed Switch Console Login Screen
The user can now enter commands to manage the Switch. For a detailed descrip-
tionofthecommands,pleaserefertothefollowingchapters.
Note
1.For security reason, please change and memorize the new
passwordafterthisfirstsetup.
2.Only accept command in lowercase letter under console inter-
face.
4.2 ConguringIPAddress
The IP address conguration commands for VLAN1 interface are listed below.
Before using in-band management, the Managed Switch must be congured with
an IP address by out-of-band management (i.e. console mode). The conguration
commandsareasfollows:
SGS-6341-Series# cong
SGS-6341-Series(cong)# interface vlan 1
SGS-6341-Series(cong-if-Vlan1)# ip address 192.168.1.254 255.255.255.0

8
ThepreviouscommandwouldapplythefollowingsettingsfortheManagedSwitch.
IPv4 Address: 192.168.1.254
Subnet Mask: 255.255.255.0
Figure 4-4 Conguring IPv4 Address Screen
To check the current IP address or modify a new IP address for the Managed
Switch,pleaseusetheprocedureasfollows:
Show the current IP address
1. On “SGS-6341-Series#” prompt, enter “show ip interface brief”.
2.The screen displays the current IP address, subnet mask and gateway as shown
inFigure4-5.
Figure 4-5 Showing IP Information Screen
If the IP is successfully congured, the Managed Switch will apply the new IP
address setting immediately. You can access the Web interface of Managed Switch
throughthenewIPaddress.
Note
Ifyouarenotfamiliarwithconsolecommandortherelatedparam-
eter, enter “help”anytimeinconsoletogetthehelpdescription.

9
4.3 Setting1000BASE-XforSFP+Port
TheManagedSwitch supportsboth1000BASE-Xand 10GBASE-XSFPtransceiver
bymanual settingand thedefault SFP+port speedis setto 10Gbps.Forexample,
to establish the ber connection with 1000BASE-X SFP transceiver in the Ethernet
1/0/25,thefollowingcommandcongurationisrequired:
SGS-6341-Series#cong
SGS-6341-Series(cong)#interface ethernet 1/0/25
SGS-6341-Series(cong-if-ethernet1/0/25)#speed-duplex force1g-full
Figure 4-6 Setting 1000BASE-X Screen
4.4 SavingtheConguration
In Managed Switch, the running conguration le stores in the RAM. In the
current version, the running conguration sequence running-cong can be saved
from the RAM to FLASH by write command or copy running-cong startup-
congcommand,sothattherunning congurationsequencebecomesthe start-up
congurationle,whichiscalledcongurationsave.
SGS-6341-Series# copy running-cong startup-cong
SGS-6341-Series# write
Figure 4-7 Copying Running-cong Startup-cong Screen

10
5. Starting Web Management
The Managed Switch provides a built-in browser interface. You can manage it
remotely by having a remote host with Web browser, such as Microsoft Internet
Explorer,MozillaFirefox,GoogleChromeorAppleSafari.
PC / Workstation
with Web Browser
192.168.0.x
Managed Switch
RJ45/UTP Cable
IP Address:
192.168.0.254
Figure 5-1 IP Management Diagram
The following shows how to start up the Web Management of the Managed
Switch. Please note the Managed Switch is congured through an Ethernet
connection. Please make sure the manager PC must be set to the same IP subnet
address.
For example, the IP address of the Managed Switch is congured with
192.168.0.254, then the manager PC should be set to 192.168.0.x (where x
is a number between 1 and 253, except 254), and the default subnet mask is
255.255.255.0.
Thefactorydefaultusernameandpasswordareasfollows:
DefaultIP:192.168.0.254
Username:admin
Password:admin

11
5.1 Logging in to the Managed Switch
1.Use Internet Explorer 8.0 or above Web browser and enter IP address
http://192.168.0.254toaccesstheWebinterface.
2.When the following dialog box appears, please enter the congured username
“admin”and password“admin” (ortheusername/password youhavechanged
viaconsole).TheloginscreeninFigure5-2appears.
Figure 5-2 Login Screen

12
3.Afterenteringthepassword,themainscreenappearsasshowninFigure5-3.
Figure 5-3 Web Main Screen of Managed Switch
4.The Switch Menu on the left of the Web page lets you access all the commands
andstatisticstheSwitchprovides.
Now, you can use the Web management interface to continue the Switch
management or manage the Managed Switch by console interface. Please refer to
theusermanualformore.

13
5.2SavingCongurationviatheWeb
In the Managed Switch, the running conguration le stores in the RAM. In the
currentversion, therunning congurationsequenceof running-congcan besaved
from the RAM to FLASH by “Save current running-congurations” function,
so that the running conguration sequence becomes the startup conguration le,
whichiscalledcongurationsave.
To save all applied changes and set the current conguration as a startup
conguration, the startup-conguration le will be loaded automatically across a
system reboot.
1. Click “Switch basic conguration > Switch basic conguration > Save
current running-conguration” to login  “Save current running-conguration”
Page.
2. Press the “Apply” button to save current running-conguration to start up
conguration.

14
6.RecoveringBacktoDefaultConguration
To reset the IP address to the default IP address “192.168.0.254” or reset the
login password to default value, press the hardware reset button on the rear
panel for about 10 seconds. After the device is rebooted, you can login the
managementWebinterfacewithinthesamesubnetof192.168.0.xx.
Console
115200,N,8,1
MGMT
USB SYS
PWR
PoE
MGMT
Reset
25 26 27 28
L3 24-Port Gigabit 802.3at+4-Port
10G SFP+ Stackable Managed Switch
Figure 6-1: SGS-6341-24P4X Reset Button
Console
115200,N,8,1
MGMT
USB
SYS
PWR
MGMT
Reset
25 26 27 28
Layer3 24-Port 10/100/1000T+
4-Port 10G SFP+ Stackable Managed Switch
Figure 6-2: SGS-6341-24T4X Reset Button

15
49 51
50 52
MGMTUSB
Reset
PWR SYS
MGMT
Console
Figure 6-3: SGS-6341-48T4X Reset Button
MGMT
USB
RESET
DC
PWR
SYS
MGMT
Console
115200,N,8,1
25 26 27 28
Figure 6-4: SGS-6341-16S8C4XR Reset Button

16
7. Customer Support
Thank you for purchasing PLANET products. You can browse our online FAQ
resource at the PLANET Web site rst to check if it could solve your issue. If you
needmoresupportinformation,pleasecontactPLANETswitchsupportteam.
PLANETonlineFAQs:
http://www.planet.com.tw/en/support/faq.php?type=1
Switchsupportteammailaddress:
[email protected]
SGS-6341SeriesUser’sManual
http://www.planet.com.tw/en/support/download.php?type1=1&model=&type=3#list
(Please select your switch model name from the drop-down menu of Product
Models.)
Copyright©PLANETTechnologyCorp.2018.
Contents are subject to revision without prior notice.
PLANETisaregisteredtrademarkof PLANETTechnologyCorp.All othertrademarks
belong to their respective owners.