Planet FSD-1600 User manual

Trademarks
Copyright  PLANET Technology Corp. 2004
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners. Contents in this docu-
ment are subject to revision without prior notice.
FCC Class A Appliance
This equipment generates and uses radio frequency energy. If it is not installed
and used properly in strict accordance with the manufacturer‘s instructions,
it may cause interference to radio and television reception. It has been type-
tested and found to comply the specications in sub-part J of Part 15 of FCC
Rules, which are designed to provide reasonable protection against such inter-
ference in a residential installation. There is no guarantee that interference will
not occur in a particular installation. If this equipment does cause interference
to radio or television reception which can be determined by turning the equip-
ment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
Re-orient the receiving antenna
Relocate the computing device with respect to the receiver
Move the computer away from the deceiver
Plug the computer into a different outlet so that compute and receiver are on
different electrical circuits.
If necessary the user should consult the dealer or an experienced radio or
television technician for additional suggestions.
CE Mark Warning
This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
Revision
The information in this manual is subject to change without notice.
User's manual for PLANET 8/16-port 10/100Mbps Fast Ethernet Switch
Model: FSD-800/1600/801/1601SC & ST
Rev: 4.0 (July. 2004)
Part No. 2010-000004-003

1
Table of Contents
Chapter 1 General Introduction 1
1.1 Checklist 1
1.2 Introduction 1
1.3 Features 2
Chapter 2 Hardware Description 3
2.1 Front Panel 3
2.1.1 FSD-800/FSD-801 3
2.1.2 FSD-1600/FSD-1601 4
2.2 Rear Panel 5
2.3 Hardware Installation 7
Chapter 3 Configuration and Application 8
3.1 The Switch Operation 8
3.2 The Smart Function (16-port model) 9
3.2.1 TP or Fiber-optic selection (for FSD-1601 only) 9
3.2.2 Port-based VLAN 10
3.2.3 Port-Trunking 10
3.2.4 IP ToS/DS (DiffServ), VLAN Tag Based QoS 10
3.2.5 Port-based priority 11
3.3 Application 11
3.3.1 Basic 100Mbps Server, PCs to 10/100Mbps Switch 11
3.3.2 Connect to 100Base-FX Switch/Device (Model: FSD-801/1601)
12
3.3.3 Set up the workgroup and uplink to the backbone (Model: FSD-
1600/1601) 13
Chapter 4 Troubleshooting 14
Appendix A Specifications 15
Appendix B RJ-45 Pin Specification 17

1
Chapter 1
General Introduction
1.1 Checklist
Check the contents of your package for following parts:
• The Fast Ethernet Switch
• User’s Manual
• Power Cord
If any of these pieces are missing or damaged, please contact your dealer immediately, if
possible, retain the carton including the original packing material, and use them against
to repack the product in case there is a need to return it to us for repair.
1.2 Introduction
The 8/16-port 10/100Mbps Ethernet Switch is designed to allow simultaneous
transmission of multiple packets via an internal high-speed data channel. This means that
it can partition a network more efciently than bridges or routers in most environments.
This Switch is a highly reliable network switch and is the ideal device for bridging Ethernet
to Fast Ethernet workgroups or networks. Simple and cost-effective, the Switch complies
to IEEE802.3u, IEEE802.3, 100Base-TX, and 10Base-T. Therefore, the Switch will be the
fast being recognized as one of the most important building blocks for today networking
technology. Choice of 100Base-FX optic-ber ST/SC interface,
The FSD-801/1601ST&SC are also ideal to extend the network distance up to 2 kilometers
away as a link to your remote backbone.
The Switch also provide rack-mounting kits option for being installed On 10-inch or 19-
inch rack to ease the placement and management effort.
Compact in size and designed for Plug and Play installation, the Switch allows the network
administrator to simply connect the network and power cables and the switching/bridging
functions begin automatically. No hardware or software congurations are required.
The front panel of the Switch provides LED indicators for easy recognition of the switch
operation status and for troubleshooting. These LED indicators display the power status
for the system and link/activity, speed, and full-duplex status for each port.
With 8/16-port Fast Ethernet Switching designed specically for connecting workgroup
devices and desktops, companies no longer have to invest in expensive and inexible
switches engineered primarily for backbone implementations. Instead, companies can
deploy scaleable, affordable switches that increase the aggregate bandwidth of the
network by boosting throughput to the workgroups that need it most.

2
3
1.3 Features
• 8/16-port 10/100base-TX Auto-Negotiation Ethernet Switches
• One optional 100Base-FX fiber port for extending up to 2km
• Complies with the IEEE802.3 Ethernet and IEEE802.3u Fast Ethernet stan-
dard
• Features Store-and-Forward architectures with wire-speed filtering and for-
warding rates
• Provide rack-mounting kit option for 10-inch and 19-inch Rack
• Full/Half-Duplex capability on every TX ports, total bandwidth is up to
200Mbps/port
• Support up to 1K/8K Uni-cast address, Layer 2 address resolution-Self Learn-
ing
• IEEE802.3x compliant full-duplex flow control
• Back pressure half-duplex flow control
• Runt and CRC Filtering eliminates erroneous packets to optimize the network
bandwidth
• Provide internal power supply
• LED indicators for simple diagnostics and management
• Auto- MDI and MDI-X detect for easily connecting to PC or hub/Switch uplink
• DIP Switch for smart function (16-port model only)

2
3
Chapter 2
Hardware Description
This section describes the hardware features of the Switch. For easier management and
control of the Switch, familiarize yourself with its display indicators, and ports. Front panel
illustrations in this chapter display the unit LED indicators. Before connecting any network
device to the hub, read this chapter carefully.
2.1 Front Panel
The unit front panel provides a simple interface monitoring the Switch. It includes a power
indicator for each port.
2.1.1 FSD-800/FSD-801
Figure 2-1 Front Panel of FSD-800 / FSD-801
LED indicators
Printing Color Description
Power
(PWR) Green This indicator lights green when the Switch is receiving power, otherwise it is off.
LNK/
ACT Green
This indicator green when the port is connected to a either
10Mbps Ethernet or 100Mbs Fast Ethernet station, If the
station to which the Switch connected is powered off, or if
there is a problem with the link, the LED will remain off.
And the indicator blinking green when the data will be re-
ceived to all other connected ports.
100 Green
This indicator green when the port is connected to a
100Mbps Fast Ethernet station. If the station to which the
Switch is connected is powered off, a 10Mbps Ethernet
station, or if there is a problem with the link, the LED will
remain off.

4
5
FDX/
COL Amber
Lit: Full duplex operation
Unlit: Half duplex operation
Blink: indicates data collisions on the respective Ethernet
segment of this port. Whenever a collision is detected, the
respective COL indicator will briefly blink.
This is normal when the network is busy.
 NOTE:
Port # 8 of FSD-801 is a shared port. Either Twisted Pair port
or Fiber-optic port can operate in one time. Please power off
FSD-801 before switching the share port to different con-
nection type.
DIP Switch (FSD-801)
Printing Description
FDX (default) The 100Base-FX fiber port of the switch is operating in full-
duplex mode.
HDX The port is operating in half-duplex mode.
 NOTE:
check the opposite end is using the same transmit mode
before make the connection. If you want to adjust the DIP
switch, please power off FSD-801 first.
2.1.2 FSD-1600/FSD-1601
Figure 2-2 Front Panel of FSD-1600/ FSD-1601

4
5
LED indicators
Printing Color Description
Power
(PWR) Green This indicator lights green when the Switch is receiving power; otherwise, it is off.
LNK/
ACT Green
This indicator green when the port is connected to a either
10Mbps Ethernet or 100Mbs Fast Ethernet station , If the
station to which the Switch is connected is powered off, or if
there is a problem with the link, the LED will remain off.
And the indicator blinking green when the data will be re-
ceived to all other connected ports.
100 Green
This indicator green when the port is connected to a
100Mbps Fast Ethernet station. If the station to which the
Switch is connected is powered off, a 10Mbps Ethernet
station, or if there is a problem with the link, the LED will
remain off.
FDX/
COL Amber
Lit: Full duplex operation
Unlit: Half duplex operation
Blink: indicates data collisions on the respective Ethernet
segment of this port. Whenever a collision is detected, the
respective COL indicator will briefly blink
This is normal when the network is busy.
 NOTE:
Port # 16 of FSD-1601 is a shared port. Either Twisted Pair
port or Fiber-optic port can operate in one time.
2.2 Rear Panel
There is one power socket on the back of the switch, 100~240VAC, 50/60Hz. And one
more DIP-switch for FSD-1600 and FSD-1601 for smart function.
Figure 2-3 Rear Panel of the FSD-800/801
Figure 2-4 Rear Panel of the FSD-1600/1601

6
7
DIP Switch (Smart function for FSD-1600/1601)
DIP Function Description
1 TP / FX Selection ON: Enable FX
OFF: Enable TP
2Fiber Full/Half
duplex Switch
ON: Enable Fiber Full Duplex
OFF: Enable Fiber Half Duplex
3VLAN topology
type selection
ON: 15VLANs (port#1-15) with 1 overlapping
port (port#16) topology
OFF: 14VLANs (port#1-14) with 2 overlapping
port (port#15,16) topology
4 Port Based VLAN ON: Enable VLAN
OFF: NO VLAN
5Port Trunk 0
(port 1,2,3,4)
ON: Enable Trunk group 0
OFF: Disable group 0
6Port Trunk 1
(port 5,6,7,8)
ON: Enable Trunk group 1
OFF: Disable group 1
7Port Trunk 2
(port 9,10,11,12)
ON: Enable Trunk group 2
OFF: Disable group 1
8Port Trunk 3
(port 13,14,15,16)
ON: Enable Trunk group 3
OFF: Disable group 3
9
TCP/IP TOS / DS
(Diffserv)
Based QoS
ON: Enable QoS
OFF: Turn off the QoS
10 802.1Q VLAN Tag
Priority Based Qos
ON: Enable
OFF: Disable
11&12 Port Based Prior-
ity QoS
12 11 Description
Off Off Disable
Off On Port 1-2 high priority ports (2 ports)
On Off Port 1-4 high priority ports (4 ports)
On On Port 1-8 high priority ports (8 ports)

6
7
 NOTE:
1. For fiber-optic connection, please check the opposite end is us-
ing the same transmit mode before make the connection.
2. Port#16 of the switch is shared with 100Base-FX port. Make
sure either Fiber-optic or twisted pair port is being connected.
3. For more information about the Smart function, please refer to
Chapter 3.
4. All the DIP is in OFF position by default!
2.3 Hardware Installation
1. Place the Switch on a smooth surface
2. Connect the output cord of power supply to the AC inlet.
3. Connect hub or PC to one port of the Switch using Category 3/4/5 UTP/STP
cabling.
4. Connect another hub or PC to the other port of Switch by following the same
process as described in Step 3.
Notice:
Cable distance for the Switch
The cable distance between the Switch and hub / PC should not exceed 100
meter.
The fiber-optic should not exceed 412 meters in Half-duplex mode and 2 kilome-
ters for Full-duplex mode
Make sure the wiring is correct
It can be used Category 3/4/5 cable in 10Mbps operation. To reliably operate your
network at 100Mbps, you must use an Unshielded Twisted-Pair (UTP) Category 5
cable, or better Data Grade cabling. While a Category 3 or 4 cable may initially
seem to work, it will soon cause data loss.
The fiber-optic cable should be a multi-mode fiber cable with 62.5/125μm or
50/125μm in specification.
You can find the information from the printing of the cable. If you are not familiar
with it, please consult your local dealers for the information.
Power System
The Switch accepts AC input with 100~240V AC, 50/60Hz. To prevent from data
loss or network downtime, consider install an UPS (Un-interrupt Power Supply) for
the Switch. And in some area, a surge suppression device also can help to prevent
from the Switch being damaged by un-regulated surge or current to it.
All kinds of hub / PC can connect to switch by using straight-through wires. The Switch
also supports auto MDI detection. This means you can direct connect any port of the
Switch to another MDI-X devices with a straight wire.