Planet IGS-5227-4MP2MT User manual

Industrial IP67-rated
4-Port 10/100/1000T 802.3at PoE
+ 2-Port 10/100/1000T
Managed Ethernet Switch (-40~75 degrees C, 24V)
IGS-5227-4MP2MT
Quick Installation Guide

Table of Contents
1. Package Contents ....................................................................................... 3
2. M12 A-coded Connector Pin Assignment ....................................................... 4
3. M12 (8-pin, A-coded Male) to RJ45 (8-pin) Straight-through UTP Cabling ........ 5
4. Connecting M12 Cable to the Industrial Managed Switch................................ 6
5. M23 DC Power Cable Pin Assignment ........................................................... 9
6. Requirements ............................................................................................10
7. Starting Web Management .........................................................................11
8. SavingCongurationviaWeb .....................................................................14
9. RecoveringBacktoDefaultConguration.....................................................15
10. Customer Support ....................................................................................16

3
1. Package Contents
Thank you for purchasing PLANET Industrial L2+ Managed Ethernet Switch.
“Industrial Managed Switch” is used as an alternative name in this Quick
Installation Guide. Open the box of the Industrial Managed Switch and carefully
unpack it. The box should contain the following items:
The Industrial Managed Switch x 1
Quick Installation Guide x 1
2m 8-pin A-coded M12-to-RJ45 UTP Cable x 1
DIN Rail Kit x 1
Wall-mount Kit x 1
If any item is found missing or damaged, please contact your local reseller for
replacement.

4
2. M12 A-coded Connector Pin Assignment
The industrial managed switch front panel provides six 10/100/1000BASE-T
Ethernet ports in the form of M12 8-pin A-coded female connector. These ports are
designed for Ethernet equipment connection through Cat5/5e UTP cables. The M12
8-pin A-coded input interface pinout is shown below:
Pin Con
1DA+
2DA
5DC
8DD
3DB+
6DB
7DD+
4DC+
12
5
6
4
8
73
8-pin M12 A-coded Female 10/100/1000T Connector Pin Assignment

5
3. M12 (8-pin, A-coded Male) to RJ45 (8-pin) Straight-
through UTP Cabling
M12 A-code Male
Connector Pin No.
MDI 1000BASE-T
Signal ID T568B Color RJ45 Connector Pin No.
1BI_DA+ white/orange 1
2BI_DA- orange 2
3BI_DB+ white/green 3
4BI_DC+ blue 4
5BI_DC- white/blue 5
6BI_DB- green 6
7BI_DD+ white/brown 7
8BI_DD- brown 8
Note
As each Ethernet port of the Industrial Managed Switch is running
in auto negotiation mode, make sure the Ethernet ports of the
corresponding Ethernet devices are also running in auto negotiation
mode, otherwise, the Ethernet performance will be poor.

6
4. Connecting M12 Cable to the Industrial Managed
Switch
Step 1: Turn counterclockwise to remove the waterproof screw nuts of an M12
connector and M23 power input.
Step 2: Insert the M12 UTP male connector into the M12 female Gigabit Ethernet
port of the Industrial Managed Switch.

7
Step 3: Turn clockwise to tighten the screw nut of the M12 connector and make
sure the connection is tight.
Step 4: Insert the M23 power female connector into the M23 male port of the
power input.
Note
The box doesn’t contain the M23 5-pin A-coded female connector
power cable.

8
Step 5: Turn clockwise to tighten the screw nut of the M23 power connector.
Note
Before connecting the DC power cord, please check whether your
local DC power source is stable.
Note
Make sure to tightly close all interfaces to have waterproof effect.

9
5. M23 DC Power Cable Pin Assignment
The front panel of the Industrial Managed Switch provides one M23 DC power
5-pin male connector for DC power input. Please use the power cable with the M23
DC power 5-pin female connector from the Industrial Managed Switch package for
DC power input. The M23 DC power cable pin assignment is shown below:
Note
1. The box doesn’t contain the M23 5-pin A-coded female
connector power cable.
2. Please contact your local reseller to purchase CB-M23F5F-120
from PLANET.
V2-
V2+
V1-
V1+
CB-M23F5F-120 M23 DC power cable pin assignment and wiring code
V2-
V2+
V1-
V1+
V1 positive (+) pin = white cable
V1 negative (-) pin = brown cable
V2 positive (+) pin = black cable
V2 negative (-) pin = yellow cable
Note
A. Make sure you connect the correct power pin to your DC power
source.
1. The wire gauge for the power cable should be in the range of
12 ~ 24 AWG.
2. The DC power input range is 24 ~ 48V DC.
B. There are two methods to install the Industrial Managed Switch
– DIN-rail mounting and wall-mount plate mounting. For more
detailed information, please refer to Chapter 2 of the user’s
manual.

10
6. Requirements
Workstations running Windows XP/2003/Vista/7/8/10/2008, MAC OS X or later,
Linux, UNIX, or other platforms are compatible with TCP/IP Protocols.
Workstations are installed with Ethernet NIC (Network Interface Card)
Ethernet Port Connection
Network cables -- Use standard network (UTP) cables with RJ45 connectors.
The above PC is installed with Web browser and JAVA runtime environment plug-in.
Note
It is recommended to use Internet Explore 8.0 or above to access
the Industrial Managed Switch. If the Web interface of the Indus-
trial Managed Switch is not accessible, please turn off the anti-virus
software or firewall and then try it again.