Planet WGS-5225-8MT User manual

Industrial L2+ 8-Port 10/100/1000T M12
Wall-mount Managed Switch
WGS-5225-8MT
Quick Installation Guide

Table of Contents
1. Package Contents ....................................................................................... 3
2. M12 X-coded cable ..................................................................................... 4
2.1 M12 X-coded Connector Pin Assignment ................................................ 4
2.2 M12 (8-pin, X-coded Male) to RJ45 (8-pin) Straight-through UTP Cabling. 4
2.3 Connecting M12 Cable to the WGS-5225-8MT ........................................ 5
3. M12 DC Power Cable .................................................................................. 7
4. Requirements ............................................................................................. 8
5. Hardware Installation .................................................................................. 9
5.1 Wall Mount Installation......................................................................... 9
5.2 Wall Hanging Installation.....................................................................10
5.3 Magnet Installation .............................................................................11
5.4 DIN-rail Mounting ...............................................................................12
6. Web Login.................................................................................................14
6.1 Starting Web Management ..................................................................14
 6.2 SavingCongurationviatheWeb ........................................................16
7. RecoveringBacktoDefaultConguration.....................................................17
8. Customer Support .....................................................................................18

3
1. Package Contents
Thank you for purchasing PLANET Industrial L2+ 8-Port 10/100/1000T M12 Wall-
mount Managed Switch. The table below shows the model with the number of
ports
Model Name 10/100/1000T M12 ports, 8-pin X-coded female connector
WGS-5225-8MT 8
In the following sections, unless specied, the term “Wall-mount Managed
Switch” mentioned in this quick installation guide refers to the above model.
Open the box of the Wall-mount Managed Switch and carefully unpack it. The box
should contain the following items:
The Wall-mount
Managed Switch x 1
Quick Installation
Guide x 1 pc
Wall-mounted Kit x
1 set
Magnet Kit x
1 set
DIN-rail Kit x 1
set
2m 8-pin X-coded M12-to-RJ45
UTP Cable x 1
1.2m M12 Power Cable
x 1
If any item is found missing or damaged, please contact your local reseller for
replacement.

4
2. M12 X-coded cable
2.1 M12 X-coded Connector Pin Assignment
The WGS-5225-8MT front panel provides eight 10/100/1000BASE-T Ethernet
ports in the form of M12 8-pin X-coded female connector. These ports are
designed for Ethernet equipment connection through Cat5/5e UTP cables. The M12
8-pin X-coded input interface pinout is shown below:
Pin Con
1DA+
2DA
5
8
3DB+
6
7
DD+
DD
DC
DB4
DC+
6
3
7
2
4
5
1
8
8-pin M12 X-coded Female 10/100/1000T Connector Pin Assignment
2.2 M12 (8-pin, X-coded Male) to RJ45 (8-pin) Straight-through
UTP Cabling
M12 X-coded Male
Connector Pin No.
MDI
1000BASE-T Signal ID T568B Color RJ45 Connector
Pin No.
1BI_DA+ white/orange 1
2BI_DA- orange 2
3BI_DB+ white/green 3
4BI_DB- green 6
5BI_DD+ white/brown 7
6BI_DD- brown 8
7BI_DC- White/blue 5
8BI_DC+ blue 4

5
Note
As each Ethernet port of the Wall-mount Managed Switch is
running in auto negotiation mode, make sure the Ethernet ports of
the corresponding Ethernet devices are also running in auto nego-
tiation mode; otherwise, the Ethernet performance will be poor.
2.3 Connecting M12 Cable to the WGS-5225-8MT
Note
Follow the steps below to connect M12 cables to the WGS-
5225-8MT.
Step 1: Turn counterclockwise to remove the waterproof caps of an M12
connector and power input.
Step 2: Insert the M12 UTP male connector into the M12 female Gigabit Ethernet
port of the Wall-mount Managed Switch.

6
Step 3: Turn clockwise to tighten the cable of the M12 connector and make sure
the connection is tight.
Step 4: Insert the M12 power female connector into the M12 male port of the
power input.
Step 5: Turn clockwise to tighten the cable connecting to the M12 power
connector.
Caution
To have the vibration-proof effect, connectors must be totally tight-
ened.

7
3. M12 DC Power Cable
Pin Assignment
The front panel of the Wall-mount Managed Switch provides one M12 DC power
5-pin male connector for DC power input. Please use the power cable with the M12
DC power 5-pin female connector from the Wall-mount Managed Switch package
for DC power input. The M12 DC power cable pin assignment is shown below:
M12 DC power cable pin assignment and wiring code
V1−
V1+
V2−
V2+
V1 positive (+) pin = blue cable
V1 negative (-) pin = white cable
V2 positive (+) pin = black cable
V2 negative (-) pin = brown cable
Note
Make sure you connect the correct power pin to your DC power
source.
1. The wire gauge for the power cable should be in the range of 12
~ 24 AWG.
2. The DC power input range is 9 ~ 48V DC.

8
4. Requirements
zWorkstations running Windows XP/2003/Vista/7/8/2008/10, MAC OS X or later,
Linux, UNIX, or other platforms are compatible with TCP/IP protocols.
zWorkstations are installed with Ethernet NIC (Network Interface Card)
zEthernet Port Connection
Network cables -- Use network (UTP) cables with M12 (X-coded) and RJ45
connectors.
The above PC is installed with Web browser.
Note
It is recommended to use Internet Explorer 8.0 or above to access
the Wall-mount Managed Switch. If the Web interface of the Wall-
mount Managed Switch is not accessible, please turn off the anti-
virus software or firewall and then try it again.

9
5. Hardware Installation
5.1 Wall Mount Installation
To install the Wall-mount Managed Switch on the wall, simply follow the following
steps:
Step 1: It is required 4 holes with 8mm diameter on the wall; the distance
between the 2 holes is 230 mm and the line through them must be
horizontal.
230mm
124mm
Ø4mm
6mm
Ø8mm
Step 2: Install a conductor pipe inside the board hole and ush the edge of the
conductor pipe with the wall surface.
Step 3: Screw the bolts into the conductor pipe. The Wall-mount Managed Switch
is between bolts and conductor pipe, as shown below.
ACTLNK
ACTLNK
1000
100
SYS
PWR
180W
240W
SFP
17
18
120W
60W
5 731
6 842
13 15119
14 161210
PoE
SFP
17 18
WGS-4215-16P2S
Managed
Fiber
PoE+ Magnet Mounting
PoE-in-Use
LNK/ACT
PoE Usage
V+
Ground
DC Input Range
48-56V , 5.8A max.
WGS-5225-8MT
Managed
Bypass Relay Magnet Mounting
Alarm
PWR 2
PWR 1
Ring
R.O.
2
1
4
3
6
5
8
7
Pin Con
1 DA+
2 DA
5
8
3 DB+
6
7
DD+
DD
DC
DB4
DC+
6
3
7
2
4
5
1
8
V2
V2
V1
V1
2468
1357
DC Input:
9V-48V
, 1.3A max.
Power
Normal
Power
Failure
10/10010/10010/10010/100
10001000
LNK/ACTLNK/ACT
LNK/ACTLNK/ACT
Bypass Relay
230mm
124mm

10
5.2 Wall Hanging Installation
To hang the Wall-mount Managed Switch on the wall, simply follow the following
steps:
Step 1: Drill 2 holes (one hole on each side) with 8mm diameter on the wall; the
distance between the 2 holes is 230 mm and the line through them must
be horizontal.
Step 2: Place two anchors inside the board hole by hammering them. Then screw
the two screws leaving a space of 2mm apart as shown in the circled
diagram below.
1 2
ACTLNK
ACTLNK
1000
100
SYS
PWR
180W
240W
SFP
17
18
120W
60W
5 731
6 842
13 15119
14 161210
PoE
SFP
17 18
WGS-4215-16P2S
Managed
Fiber
PoE+ Magnet Mounting
PoE-in-Use
LNK/ACT
PoE Usage
V+
Ground
DC Input Range
48-56V , 5.8A max.
WGS-5225-8MT
Managed
Bypass Relay Magnet Mounting
Alarm
PWR 2
PWR 1
Ring
R.O.
2
1
4
3
6
5
8
7
Pin Con
1 DA+
2 DA
5
8
3 DB+
6
7
DD+
DD
DC
DB4
DC+
6
3
7
2
4
5
1
8
V2
V2
V1
V1
2468
1357
DC Input:
9V-48V
, 1.3A max.
Power
Normal
Power
Failure
10/10010/10010/10010/100
10001000
LNK/ACTLNK/ACT
LNK/ACTLNK/ACT
Bypass Relay
2mm
4mm Screw
Step 3: The switch, shown in the picture below, can now be hung on the wall.
1Place against a wall
2Hang up
ACTLNK
ACTLNK
1000
100
SYS
PWR
180W
240W
SFP
17
18
120W
60W
5 731
6 842
13 15119
14 161210
PoE
SFP
17 18
WGS-4215-16P2S
Managed
Fiber
PoE+ Magnet Mounting
PoE-in-Use
LNK/ACT
PoE Usage
V+
Ground
DC Input Range
48-56V , 5.8A max.
WGS-5225-8MT
Managed
Bypass Relay Magnet Mounting
Alarm
PWR 2
PWR 1
Ring
R.O.
2
1
4
3
6
5
8
7
Pin Con
1 DA+
2 DA
5
8
3 DB+
6
7
DD+
DD
DC
DB4
DC+
6
3
7
2
4
5
1
8
V2
V2
V1
V1
2 4 6 8
1 3 5 7
DC Input:
9V-48V
, 1.3A max.
Power
Normal
Power
Failure
10/10010/10010/10010/100
10001000
LNK/ACTLNK/ACT
LNK/ACTLNK/ACT
Bypass Relay
4mm Screw

11
5.3 Magnet Installation
To install the Wall-mount Managed Switch on a magnetic surface, simply follow the
following diagram:
Magnet Installation
Step 1: There are six holes in front, using six sets of magnets to install. Please
refer to the following.
Step 2: Turn the switch to the back, then screw the magnet to the middle hole.
ACTLNK
ACTLNK
1000
100
SYS
PWR
180W
240W
SFP
17
18
120W
60W
5 731
6 842
13 15119
14 161210
PoE
SFP
17 18
WGS-4215-16P2S
Managed
Fiber
PoE+ Magnet Mounting
PoE-in-Use
LNK/ACT
PoE Usage
V+
Ground
DC Input Range
48-56V , 5.8A max.
WGS-5225-8MT
Managed
Bypass Relay Magnet Mounting
Alarm
PWR 2
PWR 1
Ring
R.O.
2
1
4
3
6
5
8
7
Pin Con
1 DA+
2 DA
5
8
3 DB+
6
7
DD+
DD
DC
DB4
DC+
6
3
7
2
4
5
1
8
V2
V2
V1
V1
2468
1357
DC Input:
9V-48V
, 1.3A max.
Power
Normal
Power
Failure
10/10010/10010/10010/100
10001000
LNK/ACTLNK/ACT
LNK/ACTLNK/ACT
Bypass Relay
Caution
Make sure the equipment is securely magnetically-mounted as
strong vibration could cause it to drop or break.

12
Note
Please use the screw from the magnet kit to avoid breaking the
device.
5.4 DIN-rail Mounting
The DIN-rail kit is included in the package. When the wall mounting of the Wall-
mount Managed Switch needs to be replaced with DIN-rail mounting, refer to the
followinggures toscrew theDIN-railonthe Wall-mountManagedSwitch.Tohang
up the Wall-mount Managed Switch, follow the steps below:
Step 1: Screw the DIN-rail on the Wall-mount Managed Switch.

13
Step 2: Lightly insert the DIN-rail into the track.
ACTLNK
ACTLNK
1000
100
SYS
PWR
180W
240W
SFP
17
18
120W
60W
5 731
6 842
13 15119
14 161210
PoE
SFP
17 18
WGS-4215-16P2S
Managed
Fiber
PoE+ Magnet Mounting
PoE-in-Use
LNK/ACT
PoE Usage
V+
Ground
DC Input Range
48-56V , 5.8A max.
1Push
2Click
ACTLNK
ACTLNK
1000
100
SYS
PWR
180W
240W
SFP
17
18
120W
60W
5 731
6 842
13 15119
14 161210
PoE
SFP
17 18
WGS-4215-16P2S
Managed
Fiber
PoE+ Magnet Mounting
PoE-in-Use
LNK/ACT
PoE Usage
V+
Ground
DC Input Range
48-56V , 5.8A max.
WGS-5225-8MT
Managed
Bypass Relay Magnet Mounting
Alarm
PWR 2
PWR 1
Ring
R.O.
2
1
4
3
6
5
8
7
Pin Con
1 DA+
2 DA
5
8
3 DB+
6
7
DD+
DD
DC
DB4
DC+
6
3
7
2
4
5
1
8
V2
V2
V1
V1
2 4 6 8
1 3 5 7
DC Input:
9V-48V
, 1.3A max.
Power
Normal
Power
Failure
10/10010/10010/10010/100
10001000
LNK/ACTLNK/ACT
LNK/ACTLNK/ACT
Bypass Relay
Step 3: Check whether the DIN-rail is tightly on the track.
ACTLNK
ACTLNK
1000
100
SYS
PWR
180W
240W
SFP
17
18
120W
60W
5 731
6 842
13 15119
14 161210
PoE
SFP
17 18
WGS-4215-16P2S
Managed
Fiber
PoE+ Magnet Mounting
PoE-in-Use
LNK/ACT
PoE Usage
V+
Ground
DC Input Range
48-56V , 5.8A max.
ACTLNK
ACTLNK
1000
100
SYS
PWR
180W
240W
SFP
17
18
120W
60W
5 731
6 842
13 15119
14 161210
PoE
SFP
17 18
WGS-4215-16P2S
Managed
Fiber
PoE+ Magnet Mounting
PoE-in-Use
LNK/ACT
PoE Usage
V+
Ground
DC Input Range
48-56V , 5.8A max.
WGS-5225-8MT
Managed
Bypass Relay Magnet Mounting
Alarm
PWR 2
PWR 1
Ring
R.O.
2
1
4
3
6
5
8
7
Pin Con
1 DA+
2 DA
5
8
3 DB+
6
7
DD+
DD
DC
DB4
DC+
6
3
7
2
4
5
1
8
V2
V2
V1
V1
2 4 6 8
1 3 5 7
DC Input:
9V-48V
, 1.3A max.
Power
Normal
Power
Failure
10/10010/10010/10010/100
10001000
LNK/ACTLNK/ACT
LNK/ACTLNK/ACT
Bypass Relay

14
6. Web Login
6.1 Starting Web Management
The following shows how to start up the Web Management of the Wall-mount
Managed Switch. Note the Wall-mount Managed Switch is congured through an
Ethernet connection. Please make sure the manager PC must be set to the same
IP subnet address.
For example, the default IP address of the Wall-mount Managed Switch is
192.168.0.100, then the manager PC should be set to 192.168.0.x (where x
is a number between 1 and 254, except 100) and the default subnet mask is
255.255.255.0.
PC / Workstation
with Web Browser
192.168.0.x
Managed Switch
RJ45/UTP Cable
IP Address: 192.168.0.100
Figure 6-1: IP Management Diagram
Logging in to the Wall-mount Managed Switch
1. Use Internet Explorer 8.0 or above Web browser and enter IP address
http://192.168.0.100 to access the Web interface.
2. When the following dialog box appears, please enter “admin” in both the
defaultusernameandpasswordelds.TheloginscreeninFigure6-2appears.
Default IP Address: 192.168.0.100
Default Username: admin
Default Password: admin
Figure 6-2: Web Login Screen

15
3. After entering the password, the main screen appears as Figure 6-3 shows.
Figure 6-3: Web Main Screen of Wall-mount Managed Switch
The Switch Menu on the top of the Web page lets you access all the commands
and statistics the Wall-mount Managed Switch provides. The Switch Menu always
contains one or more buttons, such as “System”, “Switching”, “Routing”, “QoS”,
“Security”, “Ring” and “Maintenance”.
Figure 6-4: Switch Menu
Note
If you are not familiar with Switch functions or the related param-
eter, press “Help icon” anytime on the Web page to get the help
description.

16
6.2 SavingCongurationviatheWeb
To save all applied changes and set the current conguration as a startup
conguration, the startup-conguration le will be loaded automatically across a
system reboot.
1. Click the Save icon on the top Switch Menu bar.
2. Press the “Save Conguration” button.
3. Or the other way to save the setting is to Click Maintenance, Save Startup
Cong.

17
7.RecoveringBacktoDefaultConguration
IP Address has been changed or admin password has been forgotten –
To reset the IP address to the default IP address “192.168.0.100” or reset the
login password to default value, press the reset button on the front panel for
about 5 seconds. After the device is rebooted, you can log in the Web interface
management within the same subnet of 192.168.0.xx.
Reset
Figure 7-1: WGS-5225-8MT Reset Button

18
8. Customer Support
Thank you for purchasing PLANET products. You can browse our online FAQ
resourceand User’sManualonPLANET Websiterst tocheckifitcould solveyour
issue. If you need more support information, please contact PLANET switch support
team.
PLANET online FAQs:
https://www.planet.com.tw/en/support/faq
Switch support team mail address:
[email protected]
WGS-5225-8MT User’s Manual:
https://www.planet.com.tw/en/support/downloads?&method=keyword&keyword=W
GS&view=3#list
Copyright © PLANET Technology Corp. 2021
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.