Planet SW-502 User manual

10/100Mbps
Fast Ethernet Switch
SW-502/SW-802
User's Manual

Trademarks
Copyright ©PLANET Technology Corp. 2005.
Content subjects to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will
work properly in all environments and applications, and makes
no warranty and representation, either implied or expressed,
with respect to the quality, performance, merchantability, or
fitness for a particular purpose.
PLANET has made every effort to ensure that this User's
Manual is accurate; PLANET disclaims liability for any
inaccuracies or omissions that may have occurred.
Information in this User's Manual is subject to change without
notice and does not represent a commitment on the part of
PLANET. PLANET assumes no responsibility for any
inaccuracies that may be contained in this User's Manual.
PLANET makes no commitment to update or keep current the
information in this User's Manual, and reserves the right to
make improvements to this User's Manual and/or to the
products described in this User's Manual, at any time without
notice.
If you find information in this manual that is incorrect, misleading,
or incomplete, we would appreciate your comments and
suggestions.

FCC Warning
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the Instruction manual,
may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at its own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this
product may cause radio interference, in which case the user
may be required to take adequate measures.
Revision
PLANET Fast Ethernet Switch User's Manual
FOR MODELS: GSD-503/GSD-504/GSD-803/GSD-804
Rev: 1.0(May.2005)
Part No.: 2011-A33160-000

1. INTRODUCTION
1.1 Package Contents
Check the contents of your package for following parts:
。 Fast Ethernet Switch x1
。 User's manual x1
。 Power adapter x1
If any of these are missing or damaged, please contact your dealer
immediately, if possible, retain the carton including the original
packing material, and use them against to repack the product in case
there is a need to return it to us for repair.
1.2 How to Use This Manual
This Fast Ethernet Switch User Manual is structured as follows:
Chapter 2 Installation
The chapter explains the feature, functionality and the physical
installation of the Switch.
Chapter 3 Switch operation
The chapter explains the Fast Ethernet Switch transmit operation.
Chapter 4 Troubleshooting
The chapter explains the troubleshooting of the Fast Ethernet Switch.
Appendix A
This chapter contains cable information of the Fast Ethernet Switch.
1.3 Product Features
。 Comply with IEEE 802.3, 10Base-T, IEEE 802.3u,

100Base-TX
。 5/8-port 10/100Mbps Auto-Negotiation ports - 10/20Mbps,
100/200Mbps Auto-sensing
。 Compact size design for wall mount or desktop placement
。 High performance Store-and-Forward Switching Architecture
。 Runt and CRC filtering
。 Flow control (Back Pressure) supports in half-duplex mode
。 1K MAC Address Table, automatically learning and aging
。 LED indicators array for easy diagnostic, troubleshooting
。 Plug-and-Play Installation
。 Auto-MDI/MDIX on each port

1.4 Product Specifications
Model SW-502 SW-802
Hardware Specification
Network Ports 5 10/100Base-T RJ-45
MDI/MDI-X ports
8 10/100Base-T RJ-45
MDI/MDI-X ports
Dimensions (W x D x H) 159 x 100 x 28mm
Weight (KG) 0.16 KG 0.18 KG
Power Requirement External Power adapter 12V 500 mA
Switch Specification
Switch Architecture Store-and-forward
Address Table 1K entries, auto learning/ageing
Flow Control IEEE 802.3x full duplex operating and flow control
Packet Control Runt & CRC filtering, Broadcast storm control
Standard Conformance
Network Standards IEEE 802.3 (Ethernet), IEEE 802.3u (Fast Ethernet)
and IEEE802.3x (flow control)
Operation Temperature 0~50ºC
10% to 90% (Non-condensing)
Humidity -40~70ºC
Regulation Compliance FCC, CE

2. INSTALLATION
This section describes the functionalities of the Fast Ethernet Switch’s
components and guides how to install it on the desktop. Basic
knowledge of networking is assumed. Please read this chapter
completely before continuing.
2.1 Product Description
With concepts of "Easy to Install and use", "Compact-sized design",
and "Simple troubleshooting", PLANET SW-502/SW-802 provides
cost-conscious business and home users with the foundation of an
integrated system of small-office / home-office networking. The SW
502/SW-802 is the fancy-shape plastic models and just right for your
network of 10 to 50 users.
The SW-502/SW-802 Fast Ethernet Switch is a Simple and
cost-effective, highly reliable network switch. And is the ideal device
for bridging Ethernet to Fast Ethernet workgroups or networks.
Therefore, the Switches will be the fast being recognized as one of the
most important building blocks for today networking technology.
To segment the network, ease the network traffic, the 5/8-port
10/100Mbps are useful for the SOHO switched networks as the
friendly network backbone. Provides array LED indicators, the
network status can be monitored at a glance.
2.1.1 Product Overview
PLANET SW-502/SW-802 are Fast Ethernet switches with 5/8 RJ-45
10/100 Mbps ports for high-speed network connectivity. The switches
can also automatically identify and determine the correct transmission
speed and half/full duplex mode of the attached devices with its 5/8
ports.

This product also supports store-and-forward forwarding scheme to
ensure low latency and high data integrity, eliminates unnecessary
traffic and relieves congestion on critical network paths. With an
intelligent address recognition algorithm, the switches could recognize
up to 1K different MAC address and enables filtering and forwarding at
full wire speed.
2.1.2 Switch Front Panel
Figure 2-1 & 2-2 show the front panel and rear panel of SW-502
Figure 2-1 SW-502 front panel
Figure 2-2 SW-502 rear panel
Figure 2-3 & 2-4 show the front panel and rear panel of SW-802
12345

Figure 2-3 SW-802 front panel
2.1.3 LED Indicators
Figure 2-4 SW-802 rear panel
LED Color Function
PWR Green Lights to indicate tha is powered on.t the Switch
L lly
that the switch is actively sending or
NK/ACT Green Lit: indicate the link through that port is successfu
established.
Blink: indicate
receiving data over that port.
ower Notice:
s a power-required device, it means, it will not work
P
1. The device i
till it is powered. If your networks should active all the time, please
12345678

consider using UPS (Uninterrupted Power Supply) for your device.
It will prevent you from network data loss or network downtime.
2. In some area, installing a surge suppression device may also
2.
ur Fast Ethernet Switch and make
Note: This switch does not need software configuration.
2.2.1 Desktop Installation
To install the switch on desktop, simply follow the next steps:
Step1: Attach the rubber feet to the recessed areas on the bottom of
Step2: Place the switch on desktop near a DC power source.
Step3: Keep enough ventilation space between the switch and the
Note: When choosing a location, please keep in mind the
Step4: Connect your switch to network devices. le to the
devices such
help to protect your switch from being damaged by unregulated
surge or current to the Switch or the power adapter.
2 Installing the Switch
This part describes how to install yo
connections to it. Please read the following topics and perform the
procedures in the order being presented.
the switch.
surrounding objects.
environmental restrictions discussed in Chapter 1, Section 1.4
Product Specification.
A. Connect one end of a standard network cab
10/100/1000 RJ-45 ports on the Back of the switch.
B. Connect the other end of the cable to the network
as printer servers, workstations or routers…etc.