Planet GS-5220-16P2XV Operator's manual

L2+ 16-/24-Port Gigabit PoE
+ 2-/4-Port 10G SFP+ Managed Switch
with LCD Touch Screen
GS-5220-16P2XV(R)
GS-5220-16UP2XV(R)/GS-5220-16UPL2XV(R)
GS-5220-24P4XV(R)/GS-5220-24PL4XV(R)
GS-5220-24UP4XV(R)/GS-5220-24UPL4XV(R)
Quick Installation Guide

Table of Contents
1. Package Contents ....................................................................................... 3
2. Requirements ............................................................................................. 4
3. Terminal Setup ........................................................................................... 5
4. Logon to Console........................................................................................ 6
5. ConguringIPAddress................................................................................ 7
6. Starting Web Management .......................................................................... 9
7. SavingConguration..................................................................................12
8. RecoveringBacktoDefaultConguration.....................................................13
9. LCD Touch Screen......................................................................................14
10. Customer Support.....................................................................................16

3
1. Package Contents
Thank you for purchasing PLANET L2+ 16-/24-Port Gigabit PoE + 2-/4-Port 10G
SFP+ManagedSwitchwithLCD.Thedescriptionofthismodelisshownbelow:
ModelName PoESupport 10GSFP+ PoEBudget PowerInput
GS-5220-16P2XV 16-port
802.3af/at 2300W
AC
GS-5220-16P2XVR AC/DC
GS-5220-16UP2XV
16-port
802.3af/at/bt 2
400W
AC
GS-5220-16UP2XVR AC/DC
GS-5220-16UPL2XV
600W
AC
GS-5220-16UPL2XVR AC/DC
ModelName PoESupport 10GSFP+ PoEBudget PowerInput
GS-5220-24P4XV
24-port
802.3af/at 4
400W
AC
GS-5220-24P4XVR AC/DC
GS-5220-24PL4XV
600W
AC
GS-5220-24PL4XVR AC/DC
GS-5220-24UP4XV
24-port
802.3af/at/bt 4
400W
AC
GS-5220-24UP4XVR AC/DC
GS-5220-24UPL4XV
600W
AC
GS-5220-24UPL4XVR AC/DC
“Managed PoE Switch” is used as an alternative name in this Quick Installation
Guide.
Open the box of the Managed PoE Switch and carefully unpack it. The box should
containthefollowingitems:
zTheManagedPoESwitch
zQuickInstallationGuide
zRJ45 to RS232 Cable
zRubber Feet
zTwoRack-mountingBracketswithAttachmentScrews
zPowerCord
zSFPDust-proofCaps
If any item is found missing or damaged, please contact your local reseller for
replacement.

4
2. Requirements
zWorkstations running Windows 10/XP/2003/Vista/7/8/2008, MAC OS X or later,
Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPprotocols.
zWorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard)
zSerial Port Connection(Terminal)
The above Workstations come with COM Port (DB9) or USB-to-RS232
converter.
TheaboveWorkstationshavebeen installedwith terminal emulator,suchas
HyperTerminalincludedinWindowsXP/2003.
Serial cable -- one end is attached to the RS232 serial port, while the other
endtotheconsoleportoftheManagedPoESwitch.
zEthernet Port Connection
Networkcables--Usestandardnetwork(UTP)cableswithRJ45connectors.
The above PC is installed with Web browser and JAVA runtime environment
plug-in.
Note
It is recommended to use Internet Explore 8.0 or above to access
the Managed PoE Switch. If the Web interface of the Managed PoE
Switch is not accessible, please turn off the anti-virus software or
firewallandthentryitagain.

5
3. Terminal Setup
To congure the system, connect a serial cable to a COM port on a PC or
notebookcomputerandtoRJ45typeofserialportoftheManagedPoESwitch.
Managed Switch
PC / Workstation
with
Terminal Emulation Software
Serial Port
RS232 to RJ45 Cable
Console Port
RJ45
Figure 3-1: Managed PoE Switch Console Connectivity
A terminal program is required to make the software connection to the Managed
PoESwitch.
1. Run terminal program on the OS.
2.When the following screen appears, make sure that the COM port should be
conguredas:
Baud:115200
Databits:8
Parity:None
Stopbits:1
Flowcontrol:None
Figure 3-2: COM Port Conguration

6
4. Logon to Console
Once the terminal is connected to the device, power on the Managed PoE Switch,
and the terminal will display “running testing procedures”. Then, the following
message asks to log in user name and password. The factory default user name
andpasswordareshownasfollowsandtheloginscreeninFigure4-1appears.
Username:admin
Password:admin
Figure 4-1: Managed PoE Switch Console Login Screen
The user can now enter commands to manage the Managed PoE Switch. For a
detaileddescriptionofthecommands,pleaserefertothefollowingchapters.
Note
1.For security reason, please change and memorize the new pass-
wordafterthisfirstsetup.
2.Only accept command in lowercase letter under console inter-
face.

7
5.ConguringIPAddress
TheManagedPoESwitchisshippedwithdefaultIPaddressshownbelow.
IPAddress:192.168.0.100
SubnetMask:255.255.255.0
To check the current IP address or modify a new IP address for the Switch, please
usetheproceduresasfollows:
Show the current IP Address
1.Atthe“#”prompt,enter“show ip interface brief”.
2.ThescreendisplaysthecurrentIPaddressasshowninFigure5-1.
Figure 5-1: IP Information Screen
Conguring IP Address
3.At the “#” prompt, enter the following command and press <Enter> as shown
inFigure5-2.
Switch# congure terminal
Switch(cong)# interface vlan 1
Switch(cong-if-vlan)# ip address 192.168.1.100 255.255.255.0
The previous command would apply the following settings for the Managed PoE
Switch.
IPAddress:192.168.1.100
SubnetMask:255.255.255.0
Figure 5-2: Conguring IP Address Screen

8
4.Repeatstep1tocheckiftheIPaddresshaschanged.
Store current switch conguration
5.Atthe“#”prompt,enterthefollowingcommandandpress<Enter>.
#copyrunning-congstartup-cong
Figure 5-3: Saving Current Conguration Command Screen
If the IP is successfully congured, the Managed PoE Switch will apply the new IP
addresssetting immediately. Youcanaccess theWebinterface ofthe ManagedPoE
SwitchthroughthenewIPaddress.
Note
If you are not familiar with the console command or the related
parameter, enter “help” anytime in console to get the help
description.

9
6. Starting Web Management
The following shows how to start up the Web Management of the Managed
PoE Switch. Note the Managed PoE Switch is congured through an Ethernet
connection. Please make sure the manager PC must be set to the same IP subnet
address.
Forexample,thedefaultIPaddress oftheManagedPoESwitchis192.168.0.100,
then the manager PC should be set to 192.168.0.x (where x is a number
between1and254,except100),andthedefaultsubnetmaskis255.255.255.0.
PC / Workstation
with Web Browser
192.168.0.x
Managed Switch
RJ45/UTP Cable
IP Address:
192.168.0.100
Figure 6-1: IP Management Diagram
Logging in to the Managed PoE Switch
1.Use Internet Explorer 8.0 or above Web browser and enter IP address
http://192.168.0.100(thefactorydefaultIPaddressortheonethatyouhave
justchangedinconsole)toaccesstheWebinterface.
2.When the following dialog box appears, please enter the default user name and
password “admin” (or the password you have changed via console). The login
screeninFigure6-2appears.

10
DefaultIPAddress:192.168.0.100
DefaultUsername:admin
DefaultPassword:admin
Figure 6-2: Login Screen
3.Afterenteringthepassword,themainscreenappearsasFigure6-3shows.
Figure 6-3: Web Main Screen of Managed PoE Switch

11
The Switch Menu on the left of the Web page lets you access all the commands
andstatisticstheManagedPoESwitchprovides.
Figure 6-4: Switch Menu
Note
If you are not familiar with Switch functions or the related param-
eter, press “Help icon” anytime on the Web page to get the help
description.
Now, you can use the Web management interface to continue the Switch
managementormanagetheSwitchbyconsoleinterface.
Please refer to the user’s manual for more.

12
7.SavingConguration
In the Managed PoE Switch, the running conguration le stores in the RAM. In
the current version, the running conguration sequence of running-cong can be
saved from the RAM to FLASH by executing save startup cong command, so that
the running conguration sequence becomes the startup conguration le, which is
calledcongurationsave.
To save all applied changes and set the current conguration as a startup
conguration, the startup-conguration le will be loaded automatically across a
system reboot.
1.ClickSystem,andSaveStartupCong.
2. Press the “Save Conguration” button.

13
8.RecoveringBacktoDefaultConguration
IP address has been changed or admin password has been forgotten –
To reset the IP address to the default IP address “192.168.0.100” or reset the
login password to default value, press the hardware reset button on the rear
panel for about 10 seconds. After the device is rebooted, you can log in the
managementWebinterfacewithinthesamesubnetof192.168.0.xx.
Figure 8-1: GS-5220 LCD Series Reset Button

14
9. LCD Touch Screen
The Managed PoE Switch has a 2.4-inch color LCD touch screen with management
functions.TaptheLCDtouchscreentowaketheLCDtouchscreen.
Figure 9-1: To wake the LCD touch screen
ThefactorydefaultLCDcongurationsareshownasfollows.
DefaultLCD:Enable
DefaultTouchScreen:Enable
DefaultBacklightTimeout: Enable
DefaultBacklightTimeoutTime:300
DefaultReadOnlyMode:Disable
DefaultScreen:MainMenu
DefaultTimeInterval:10
DefaultColorScheme:Dark
DefaultPinNumber:1234
You can use the Web management interface and click LCD, and then LCD
ManagementtochangeLCDconguration.

15
Please refer to the user’s manual for more.

16
10. Customer Support
Thank you for purchasing PLANET products. You can browse our online FAQ
resourceandUser’sManualonPLANET Website rsttocheckif itcouldsolveyour
issue.Ifyouneed moresupportinformation, pleasecontactPLANET switchsupport
team.
PLANETonlineFAQ:
http://www.planet.com.tw/en/support/faq.php?type=1
Switchsupportteammailaddress:
[email protected]
GS-5220LCDSeriesUser’sManual:
http://www.planet.com.tw/en/support/download.php?type1=1&model=&type=3
(Please select your switch model name from the drop-down menu of Product
Model.)
Copyright © PLANET Technology Corp. 2017.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their
respective owners.