Planet IGS-5225-4T2S User manual

Industrial L2+ Multi-Port Full Gigabit
Managed Ethernet Switch
IGS-5225-4T2S/IGS-5225-4P2S/IGS-5225-4UP1T2S
IGS-5225-8P4S/IGS-5225-8P4S-12V/IGS-5225-8P2T2S
IGS-5225-8P2T4S
Quick Installation Guide

Table of Contents
1. Package Contents................................................................................. 3
2. Requirements....................................................................................... 5
3. Wiring the Power Inputs ....................................................................... 6
3.1 Grounding the Device..................................................................... 8
4. Terminal Setup..................................................................................... 9
4.1. Logging on to the Console............................................................ 10
 4.2 ConguringIPAddress ................................................................. 11
5. Starting Web Management .................................................................. 13
5.1 Logging in to the Industrial Managed Switch .................................. 13
 5.2 SavingCongurationviaWeb ....................................................... 15
6. RecoveringBacktoDefaultConguration ............................................. 16
7. Customer Support .............................................................................. 19

3
1. Package Contents
Thank you for purchasing PLANET L2+ Industrial Managed Switch, IGS-5225
Series. The number of the ports of these models is as follows:
GbECopper
Ports
PoEPorts GbESFPPorts
at/af bt* 1G 2.5G*
IGS-5225-4T2S 4- - - 2
IGS-5225-4P2S 4 4 -2-
IGS-5225-4UP1T2S 5-4-2
IGS-5225-8P4S 8 8 -2 2
IGS-5225-8P4S-12V 8 8 -2 2
IGS-5225-8P2T2S 10 8- - 2
IGS-5225-8P2T4S 10 8-2 2
*bt:Compatiblewith802.3at/afPoE
*2.5G:Compatiblewith1000BASE-SX/LX/BXSFPtransceiver
“Industrial Managed Switch” mentioned in this Quick Installation Guide
refers to the above models.

4
Open the box of the Industrial Managed Switch and carefully unpack it.
The box should contain the following items for each model of the Industrial
Managed Switches:
The
Industrial
Managed
Switch
Quick
Installation
Guide
Sheet
Wall
Mounting
Kit
DB9 to
RJ45,
RS232
Console
Cable
RJ45
Dust
Cap
SFP
Dust
Cap
IGS-5225-
4T2S     5 2
IGS-5225-
4P2S     5 2
IGS-5225-
4UP1T2S     6 2
IGS-5225-
8P4S     9 4
IGS-5225-
8P4S-12V     9 4
IGS-5225-
8P2T2S     11 2
IGS-5225-
8P2T4S     11 4
If any of these are missing or damaged, please contact your dealer
immediately. If possible, retain the carton including the original packing
materials to enable you to repack the product in case there is a need to return
it to us for repair.

5
2. Requirements
The Industrial Managed Switch provides remote login interface for
management purposes. The following equipment is necessary for further
management:
zWorkstations running Windows 10/11, MAC OS 10.15 or later, Linux, UNIX,
or other platforms are compatible with TCP/IP protocols.
zWorkstationsareinstalled withEthernetNIC(NetworkInterfaceCard)
zSerialPortConnection(Terminal)
 The above Workstations come with COM Port (DB9) or USB-to-RS232
converter.
 The above Workstations have been installed with terminal emulator, such
as putty or tera term.
 Serial cable -- one end is attached to the RS232 serial port, while the
other end to the console port of the Industrial Managed Switch.
zEthernetPortConnection
 Network cables -- Use standard network (UTP) cables with RJ45 connec-
tors.
The above PC is installed with Web browser.
It is recommended to use Chrome 98.0.xxx or above to access
the Industrial Managed Switch.

6
3. Wiring the Power Inputs
The Upper Panel of the Industrial Managed Switch comes with one
6-contact terminal block. Please follow the steps below to insert the power
wire.
1.Insert positive/negative DC power wires into Contacts 1 and 2 for Power 1,
or Contacts 5 and 6 for Power 2.
IGS-5225-8P4S/IGS-5225-8P2T2S/IGS-5225-8P2T4S:DC48~54V
PWR1 PWR2
Alarm
DI1 DO0 DO1DI0 GNDGND
DC Input:
48-54V , 6A max.
Max. Fault Alarm Loading: 24V, 1A
1 2 3 4 5 6
1 2 3 4 5 6
Figure 3-1: IGS-5225-8P4S/IGS-5225-8P2T2S/IGS-5225-8P2T4S Upper Panel
IGS-5225-4UP1T2S:DC48~54V
DI1 DO0 DO1DI0 GNDGND
DC Input:
48-54V , 8.3A max.
Dual power input is required
for maximum PoE loading.
Refer to user’s manual for
more details.
PWR1 Alarm PWR2
V1+ V2+
Max. Fault Alarm Loading: 24V, 1A
1 2 3 4 5 6
1 2 3 4 5 6
Earth Ground
Figure 3-2: IGS-5225-4UP1T2S Upper Panel
IGS-5225-4T2S:DC12~48V,AC24V
Max. Fault Alarm Loading: 24V, 1A
DC Input: 12-48V
, 1.7A max.
AC Input: 24V
, 1A max.
V1+ V2+
PWR1 PWR2Alarm
1 2 3 4 5 6
Figure 3-3: IGS-5225-4T2S Upper Panel

7
IGS-5225-4P2S:DC48~56V
FaultPWR1
V1+ V2+
PWR2
Max. fault loading: 24V, 1A
DC Input: 48-56V
,
3.5A max.
1 2 3 4 5 6
Figure 3-4: IGS-5225-4P2S Upper Panel
IGS-5225-8P4S-12V:DC12~54V
PWR1 PWR2
Alarm
DI1 DO0 DO1DI0 GNDGND
DC Input:
12-54V , 6A max.
Max. Fault Alarm Loading: 24V, 1A
1 2 3 4 5 6
1 2 3 4 5 6
Figure 3-5: IGS-5225-8P4S-12V Upper Panel
2.Tightenthewire-clampscrewsforpreventingthewiresfromloosening.
123456
V+ V- V+ V-
Power 1 Power 2
Positive(+)Pin Negative(-)Pin
IGS-5225Series Pin 1/5 Pin 2/6

8
1. The wire gauge for the terminal block should be in the range
from 12 to 24 AWG.
2.Please check the wire AWG Ampere specification before
connectingPLANETIndustrialManagedSwitch.
PWR1 and PWR2 must provide the same DC voltage for pow-
er load balance while operating with dual power input.
3.1 Grounding the Device
Users MUST complete grounding wired with the device; otherwise, a sudden
lightning could cause fatal damage to the device.
PWR1 PWR2
Alarm
DI1 DO0 DO1DI0 GNDGND
DC Input:
48-54V , 6A max.
Max. Fault Alarm Loading: 24V, 1A
1 2 3 4 5 6
1 2 3 4 5 6
EMD(Lightning)damageisnotcoveredunderwarranty.

9
4. Terminal Setup
To congure the system, connect a serial cable to a COM port on a PC or
notebook computer and to RJ45 type serial (console) port of the Industrial
Managed Switch. The console port of the Industrial Managed Switch is DCE
already, so that you can connect the console port directly through PC without
the need of null modem.
PC/Workstation with
Terminal Emulation Software
RJ45 to DB9 RS232 Cable
Serial Port
Console Port
115200,N,8,1
IGS Industrial Managed Switch
11
Console
115200,N,8,1
P1 P2 Fault
DIDO
Ring
11
R.O.
12
12
PoE Usage
ACT1000 LNK
ACT100 LNK
A terminal program is required to make the software connected to the
IGS-5225seriesIndustrialManagedSwitch.
1. Run terminal program on the OS.
2.When the followingscreenappears,makesurethatthe COM port should be
conguredas:
Baud: 115200
Parity:None
Data bits: 8
Stop bits: 1
Flowcontrol:None

10
4.1. Logging on to the Console
Once the terminal has been connected to the device, power on the Industrial
Managed Switch and the terminal will display “running testing procedures”.
The following console screen is based on the IGS-
5225-4UP1T2S. The display of the other IGS-5225 series is the
sameasthatoftheIGS-5225-4UP1T2S.
Then, the following message asks to log in user name and password. The
default user name and password are shown as follows and the login screen in
Figure4-1appears
Username:admin
Password: admin
Figure 4-1: Console Login Screen
The user can now enter commands to manage the Industrial Managed Switch.
For a detailed description of the commands, please refer to the following
chapters.
1.For security reason, please change and memorize the
new password after this first setup.
2. Only accept command in lowercase letter under console inter-
face.