Planet IGS-6325 Series User manual

Industrial L3 Rack-mount
Managed Ethernet Switch
IGS-6325 Series
Quick Installation Guide

Table of Contents
1. Package Contents................................................................................. 3
2. Requirements....................................................................................... 4
3. Wiring DC Power Inputs........................................................................ 5
4. Terminal Setup..................................................................................... 7
4.1 Logging into the Console ................................................................ 8
 4.2 ConguringIPAddressviaConsole ................................................. 9
5. Starting Web Management .................................................................. 11
 5.1 LoggingintotheIndustrialManagedSwitch .................................. 12
 5.2 SavingCongurationviaWeb ....................................................... 14
6. ReturningtoDefaultConguration ....................................................... 16
7. Customer Support .............................................................................. 17

3
1. Package Contents
Thank you for purchasing PLANET Industrial L3 Managed Ethernet Switch.
“Industrial Managed Switch” is used as an alternative name in this Quick
InstallationGuide.
Open the box of the Industrial Managed Switch and carefully unpack it. The
boxshouldcontainthefollowingitemsforeachmodel:
IGS-6325-
20T4C4X
IGS-6325-
20S4C4X
IGS-6325-
24P4X
IGS-6325-
24P4S
IGS-6325-
24UP4X
Quick
Installation
Guide

DB9 to RJ45
Interface
RS232 Console
Cable

Rack-mount
AccessoryKit 
ACPowerCord   ---
RJ45 Dust Cap 25 525 25 25
SFP Dust Cap 828 844
If any item is found missing or damaged, please contact your local reseller for
replacement.

4
2. Requirements
The Industrial Managed Switch provides a remote login interface for
management purposes. The following equipment is necessary for further
management:
zWorkstations running Windows 7/8/10/11, MAC OS X 10.10 or later, Linux,
UNIX,orotherplatformsarecompatiblewithTCP/IPProtocols.
zWorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard)
zSerial Port Connection(Terminal)
 The above Workstations come with COM Port (DB9) or USB-to-RS232
converter.
 The above Workstations have been installed with terminal emulator, such
asputtyorTeraTerm,etc.
 Serial Cable -- Connect one end of the serial cable to the RS232 serial
port, and the other end to the console port of the Industrial Managed
Switch.
zEthernet Port Connection
 Network cables -- Use standard network (UTP) cables with RJ45 connec-
tors.
 TheabovePCisinstalled withWebbrowser.
It is recommended to use a modern browser, such as Google
Chrome, Mozilla Firefox, or Microsoft Edge, to access the Indus-
trial Managed Switch. If the Web interface of the Industrial
Managed Switch is not accessible, please turn off the anti-virus
softwareorfirewallandthentryitagain.

5
3. Wiring DC Power Inputs
The 6-contact terminal block connector on the panel of Industrial Managed
Switch is used for two DC redundant power inputs. Please follow the steps
below to insert the power wires.
1.Insert positive and negative DC power wires into contacts 1 and 2 for DC
POWER1,or5and6forDCPOWER2.
DI/DO
FaultR.O.
Ring
AC
DC 2
DC 1
DC POWER
ON
Fault DC 2DC 1
OFF
DC Input Range:
24-60V , 1.7A max.
GNDGNDDO 1DO 0DI 1DI 0
Max. fault loading: 24V, 1A
Figure 3-1: 6-contact terminal block connector of
IGS-6325-20T4C4X and IGS-6325-20S4C4X
+
FaultDC 1 DC 2
+
DC Input: 48-56V , 11A
Figure 3-2: 6-contact barrier terminal block of
IGS-6325-24P4X, IGS-6325-24P4S, IGS-6325-4UP4X

6
2.Tightenthewire-clampscrewstopreventthewiresfromloosening.
123456
Power 1 Alarm Power 2
+ - + -
Figure 3-3: The screws of 6-contact terminal block connector
Thewiregaugeoftheterminalblockshouldbebetween12and
24AWG.

7
4. Terminal Setup
Tocongurethesystem, connecta serialcablefromaCOMporton yourPCor
notebookcomputertotheRJ45serialportontheIndustrialManagedSwitch.
Managed Switch
PC / Workstation
with
Terminal Emulation Software
Serial Port
RS232 to RJ45 Cable
Console Port
RJ45
Figure 4-1: Console Connection for Industrial Managed Switch
A terminal program is required to establish a software connection to the
IndustrialManagedSwitch.
1. Run the terminal program on your operating system.
2.When the following screen appears, ensure that the COM port is congured
asfollows:
zBitspersecond:115200
zDatabits:8
zParity:None
zStopbits:1
zFlowcontrol:None
Figure 4-2: COM Port Conguration

8
4.1 Logging into the Console
After connecting the terminal to the device, turn on the Industrial Managed
Switch. The terminal will then display the message “running testing
procedures”.
Next, the message prompts the user to log in with their username and
password. The factory default username and password are displayed on the
loginscreen,asshowninFigure4-3(TeraTermisusedasarepresentative.).
Username:admin
Password:admin
Figure 4-3: Industrial Managed Switch Console Login Screen
Users can now enter commands to manage the Industrial Managed Switch.
For a detailed description of these commands, please refer to the following
chapters.
1.For security reasons, please change and memorize the new
passwordaftercompletingthefirstsetup.
2.Please only enter commands in lowercase letters when using
the console interface.

9
4.2 ConguringIPAddressviaConsole
The Industrial Managed Switch is shipped with a default IP address, shown
below.
IPAddress:192.168.0.100
SubnetMask:255.255.255.0
To check or modify the current IP address for the Switch, follow the
procedures below (ICS-6325-20T4C4X is used to demonstrate how to use the
commands):
Show the current IP Address
1.Atthe“#”prompt,enter“show ip interface brief”.
IGS-6325-20T4C4X # show ip interface brief
2.ThescreendisplaysthecurrentIPaddress,asshowninFigure4-4.
Figure 4-4: IP Information Screen
 Conguring IP Address
3.At the “#” prompt, enter the following command and press <Enter> as
shown in Figure 4-5.
IGS-6325-20T4C4X # congure terminal
IGS-6325-20T4C4X(cong)#interface vlan 1
IGS-6325-20T4C4X(cong-if-vlan)#ip address 192.168.1.100
255.255.255.0
The previous command would apply the following settings for the Industrial
ManagedSwitch.
IPAddress:192.168.1.100
SubnetMask:255.255.255.0

10
Figure 4-5: IP Address Conguration Screen
4.Repeatstep1tocheckiftheIPaddressischanged.
5.Enterthefollowing commandandpress<Enter> to go back to “#” prompt.
# exit
Figure 4-6: Exit Command
6.Atthe“#”prompt,enterthefollowingcommandandpress<Enter>.
# copy running-cong startup-cong
Figure 4-7: Saving Current Conguration
If the IP address is successfully congured, the Industrial Managed Switch will
immediately apply the new setting. You can access the web interface of the
IndustrialManagedSwitchusingthenewIPaddress.
If you’re unfamiliar with the console commands or related
parameters, enter “help” at any time in the console to get a
descriptionofavailablehelpoptions.