Planet IGS-1020TF User manual

Industrial 8-Port 10/100/1000BASE-T
+ 2-Port 100/1000BASE-X SFP Ethernet Switch
IGS-1020TF
User’s Manual

Table Of Contents
1. Package Contents ............................................................. 3
2. Hardware Introduction ...................................................... 4
2.1 Physical Dimensions ................................................ 4
2.2 Switch Front Panel................................................... 5
2.3 LED Indicators ........................................................ 6
2.4 Switch Upper Panel ................................................. 8
2.5 Wiring the Power Inputs .......................................... 8
2.6 Wiring the Fault Alarm Contact ............................... 10
2.7 ProductSpecications ............................................ 10
3. Installation..................................................................... 14
3.1 DIN-rail Mounting Installation ................................. 14
3.2 Wall-mount Plate Mounting..................................... 16
3.3 Installing the SFP Transceiver ................................. 17
3.4 Removing the Transceiver Module ........................... 19
4. Troubleshooting .............................................................. 20
APPENDIX A: Networking Connection.................................... 21
A.1 Switch’s RJ45 Pin Assignments................................... 21
A.2 RJ45 Cable Pin Assignments ...................................... 22
A.3 Fiber Optic Cable Connection Parameter ..................... 23
APPENDIX B: Approved PLANET SFP Transceivers .................. 25

3
1.Package Contents
Thank you for purchasing PLANET industrial 10-port Gigabit
Ethernet Switch, IGS-1020TF. In the following section, the term
“Industrial Gigabit Ethernet Switch” means the IGS-1020TF.
Open the box of the Industrial Gigabit Ethernet Switch and
carefully unpack it. The box should contain the following items:
Industrial Gigabit Ethernet Switch x 1 User’s Manual x 1
Wall-mount Kit x DIN Rail Kit x 1
If any of these are missing or damaged, please contact your
dealer immediately; if possible, retain the carton including the
original packing material, and use them again to repack the
product in case there is a need to return it to us for repair.

4
2.Hardware Introduction
2.1 Physical Dimensions
IGS-1020TF Industrial Gigabit Ethernet Switch dimensions (W
x D x H): 135 x 87.8 x 50mm
Side View
Bottom View Front View
Mounting Kit
Mounting Kit
DIN-Rail Kit
Dimensions ( unit = mm )
Top View Rear View
Input
DC12~48V, AC 24V
V1+ V1- V2+ V2-
PWR1 PWR2Fault
1 2 3 4 5 6
100/1000X SFP
109
P1 P2 FAULT
9 10
IGS-1020TF
8 6 4 2
7 5 3 1
ACT ACT
1000 LNK
LNK
10/100
100
ACT
ACT
1000
LNK LNK

5
2.2 Switch Front Panel
The front panel of the Industrial Gigabit Ethernet Switch consists
of 8 auto-sensing 10/100/1000Mbps Ethernet RJ45 ports and
2 dual speed 100/1000BASE-X SFP slots. The LED Indicators
are also located on the RJ45 ports and SFP slots of the Gigabit
Ethernet Switch.
Figure 2-1 shows the front panel of Industrial Gigabit Ethernet
Switch.
100/1000X SFP
109
P1 P2 FAULT
9 10
IGS-1020TF
8
6
4
2
7
5
3
1
ACT
ACT
1000 LNK
LNK
10/100
100
ACT
ACT
1000
LNK
LNK
Figure 2-1: IGS-1020TF Front Panel
Gigabit TP Interface
10/100/1000BASE-T Copper, RJ45 Twisted-pair: Up to 100
meters.
SFP Slot
100/1000BASE-X mini-GBIC slot, SFP (Small-form Factor
Pluggable) transceiver module: From 550 meters to 2km
(multi-mode ber) and 10/20/30/40/50/70/120 kilometers
(single-modeber).

6
2.3 LED Indicators
System
LED Color Function
P1 Green Lit: indicates power 1 has power.
P2 Green Lit: indicates power 2 has power.
FAULT Red Lit: indicates either power 1 or power 2 has
no power.
Per 10/100/1000T Port
LED Color Function
100
LNK/ACT Orange
Lit: indicates the link through that port is
successfully established at 100Mbps
or 10Mbps.
Blinking: indicates that the Switch is
actively sending or receiving data
over that port.
Off: indicates the link through that port is
successfully established at 1000Mbps.
1000
LNK/ACT Green
Lit: indicates the link through that port is
successfully established at 1000Mbps
or 10Mbps.
Blinking: indicates that the Switch is
actively sending or receiving data
over that port.
Off: indicates the link through that port is
successfully established at 100Mbps.

7
Per 100 / 1000X SFP Slot
LED Color Function
100
LNK/ACT Orange
Lit: indicates the link through that port is
successfully established at 100Mbps.
Blinking: indicates that the Switch is
actively sending or receiving data
over that port.
Off: indicates the link through that port is
successfully established at 1000Mbps.
1000
LNK/ACT Green
Lit: indicates the link through that port is
successfully established at 1000Mbps
or 10Mbps.
Blinking: indicates that the Switch is
actively sending or receiving data
over that port.
Off: indicates the link through that port is
successfully established at 100Mbps.

8
2.4 Switch Upper Panel
The upper panel of the Industrial Gigabit Ethernet Switch
consists of one terminal block connector within two DC power
inputs,
Figure 2-2 shows the upper panel of the Industrial Gigabit
Ethernet Switch.
Input
DC12~48V, AC 24V
V1+ V1- V2+ V2-
PWR1 PWR2Fault
1 2 3 4 5 6
Figure 2-2: Industrial Gigabit Ethernet Switch Upper Panel
2.5 Wiring the Power Inputs
The 6-contact terminal block connector on the top panel of
Industrial Gigabit Ethernet Switch is used for two DC redundant
power inputs. Please follow the steps below to insert the power
wire.
When performing any of the procedures like
inserting the wires or tightening the wire-clamp
screws, make sure the power is OFF to prevent
from getting an electric shock.

9
1. Insert positive and negative DC power wires into contacts 1
and 2 for POWER 1, or 5 and 6 for POWER 2.
Input
DC12~48V, AC 24V
V1+ V1- V2+ V2-
PWR1 PWR2Fault
1 2 3 4 5 6
2. Tighten the wire-clamp screws for preventing the wires from
loosening.
1 2 3 4 5 6
Power 1 Fault Power 2
+ - + -
Note
1. The wire gauge for the terminal block should be
in the range between 12 and 24 AWG.
2. The DC power input range is 12V ~ 48V DC.

10
2.6 Wiring the Fault Alarm Contact
The fault alarm contacts are in the middle of the terminal block
connector as the picture shows below. Inserting the wires, the
Industrial Gigabit Ethernet Switch will detect the fault status of
the power failure and then forms an open circuit. The following
illustration shows an application example for wiring the fault
alarm contacts.
123456
Fault Alarm Contacts
The Fault Alarm Contacts are
energized (CLOSE) for normal
operation and will OPEN when
failure occurs
Fault
Insert the wires into the fault alarm contacts
Note
1. The wire gauge for the terminal block should be
in the range between 12 and 24 AWG.
2. Alarm relay circuit accepts up to 30V, max. 3A
currents.
2.7 ProductSpecications
Model IGS-1020TF
HardwareSpecications
Copper Ports 8 x 10/100/1000BASE-T RJ45 TP
Auto-MDI/MDI-X, auto-negotiation