Plantronics Pulsar 590 series User manual

Visit www.plantronics.com/productregistration to register your
product online so we can provide you with the best possible
service and technical support.
Register Your Product Online
TABLE OF CONTENTS
PLEASE REVIEW THIS USER GUIDE CAREFULLY BEFORE USING YOUR PRODUCT.
If you need further assistance please contact Plantronics at
(866) 363-BLUE (2583). Troubleshooting information can be found on
page 13 and also on the web at www.plantronics.com/support. Please
do not return the product to the store where it was purchased.
Attention!

2
PACKAGE CONTENTS

3
FEATURES

4
FEATURES

CHARGING
1. Connect AC charger to desktop
charging stand and universal
adapter.
5
2. Lift and position earpieces inside headband
so foam ear cushions face each other.
3. Place headset into desktop charging stand.
Headset indicator light flashes when charging.
Note: Charge for 3 hours before first use.

6
POWERING
Slide power switch up for “on” and
down for “off.”
To turn on, rotate dial counterclockwise
so solid dots are aligned.
To turn off, rotate dial clockwise until
the open dot and solid dot are aligned.

1
2
Begin with headset turned off.
1. Press and hold the call control button.
2. Power headset on and when the
indicator light flashes red and blue,
release the call control button.
While headset is flashing red and blue:
3. Use the phone menu to search for
Bluetooth devices and select “590
Plantronics.”
4. When prompted for passkey,
enter 0000.
Headset will flash blue when paired
successfully.
Pairing with Bluetooth®Device
7
PAIRING
For set up and pairing instructions with Bluetooth devices other than mobile
phones, please consult your Bluetooth device user guide.

NOTE: The Pulsar 590A headset is paired with the universal adapter at the factory.
If adapter and headset continue to flash red rather than blue, connect or pair them
again. To reconnect, press the adapter pairing/connect button. To pair again, follow
directions below.
8
1
2
While headset is flashing red and blue:
3. Power adapter on.
4. Press and hold the adapter pairing/
connect button for 7-10 seconds.
When adapter is flashing red and
blue, release the button.
Headset and adapter will flash blue
when paired successfully.
Pairing Headset with Universal Adapter
Begin with headset turned off.
1. Press and hold the call control button.
2. Power headset on and when the
indicator light flashes red and blue,
release the call control button.
PAIRING

9
Position headset so that telescoping
voice tube is on right ear. Adjust
headband if necessary.
Point tip of telescoping voice tube
toward mouth and extend for optimal
voice transmission - may require two
hands.
ADJUSTING FIT

10
In-flight cable can be used with
any 3.5mm audio jack to convert
your wireless headset into wired
headphones. Headset will not
operate when in-flight cable is
connected and headset is
powered on.
1. Power headset off.
2. Insert in-flight cable into
3.5mm jack on left earpiece.
Note: Telescoping
voice tube and all
headset controls
are disabled when
in-flight cable is in
use. To control
volume, use the
device connected to
the in-flight cable,
not the headset.
IN-FLIGHT AND WIRED USES

11
HEADSET CONTROLS

12
HEADSET CONTROLS

13
TROUBLESHOOTING

14
PRODUCT SPECIFICATIONS
REGULATORY NOTICES
TECHNICAL ASSISTANCE

© 2005 Plantronics, Inc. All rights reserved. Plantronics, the logo design, Pulsar and
Sound Innovation are trademarks or registered trademarks of Plantronics, Inc.
The Bluetooth name and the Bluetooth trademarks are owned by Bluetooth SIG, Inc, and
are used by Plantronics, Inc. under license.
Printed in USA. August 2005.
Part #69828-07