Plantronics Voyager 510S User manual

www.plantronics.com
Plantronics Inc
345 Encinal Street
Santa Cruz, CA 95060 USA
Tel: [phone]
© 2005 Plantronics, Inc. All rights reserved. Plantronics, the logo design, Plantronics and the logo design combined,
and Voyager are trademarks or registered trademarks of Plantronics, Inc. The Bluetooth name and the Bluetooth
trademarks are owned by Bluetooth SIG, Inc., and are used by Plantronics, Inc. under license. Patents U.S.
5,210,791; 6,735,453; Patents Pending. Printed in USA 70084-01 (3.05)

VOYAGER™ 510S
BLUETOOTH®
HEADSET SYSTEM
User Guide

2 VOYAGER™ 510S SYSTEM DIAGRAMS
Speak volume
major adjust switch
Handset lifter
(optional) Telephone
cord jack
Telephone
receiver jack
Handset lifter jack
AC adapter
jack
Charging cradle
Power
indicator
light (red)
Call control button &
talk/on line indicator light
Charge indicator
light (amber)
Speak volume
fine adjust
buttons
Listen volume
major adjust switch
Configuration
dial
Handset Lifter
on/off switch
AC adapter
Telephone cord

3
Back Outside
VOYAGER™ 510S SYSTEM DIAGRAMS &
CONNECTING YOUR BASE
Power/mute
button
Eartip
Listen volume
adjust +/–
buttons
Horizontal
boom adjust
Charge connection
Status indicator light
(red/blue)
AC adapter
Call control button
Microphone
CONNECTING YOUR VOYAGER 510S BASE
1. Connect telephone receiver cord to receiver
jack in the Voyager 510S Bluetooth® Headset
System base (referred to as “base“ from this
point on).
Note: The access to the receiver jack
is fairly small.
2. Connect AC adapter to adapter jack in base;
plug adapter into wall socket. Red power
indicator on base will go on.
3. Connect telephone cord at rear of
base to telephone receiver jack in
telephone’s base.

4
or
BASIC INFORMATION
CHARGING YOUR HEADSET
Slide headset into charging cradle on base or charge headset
with AC adapter.
The headset status indicator will be illuminated red while
charging and change to blue when the headset is fully charged.
The headset must be charged for a minimum of 20 minutes prior
to use—3 hours to fully charge.
This User Guide provides instructions on the installation and usage of your Voyager™ 510S
Bluetooth® Headset System.
Note: The headset can also be used with other Bluetooth audio devices. See page 6 for
cell phone pairing instructions.
For safety and regulatory information, please refer to the separate “Important Safety and
Regulatory Information” booklet. A copy of the Declaration of Conformity can be found at
www.plantronics.com/documentation.
POSITIONING
YOUR SYSTEM
Positioning:
Recommended separation
distance shown above.
Important: incorrect positioning
can cause problems with noise
and interference.

5
BASIC INFORMATION
FITTING THE HEADSET
Slide the headset over
and behind your ear.
Then, press gently towards
your ear for a snug fit.
Adjust the microphone
position so that it is
directed towards your
mouth as illustrated.
POWERING THE HEADSET ON
AND OFF
To turn the headset on, press and hold
the power/mute button for 3 seconds
until the status indicator flashes blue.
To turn off, press and hold the button
again for 3 seconds until the status
indicator flashes red.
It is very important that the configuration dial
on the base is positioned correctly. Audio
problems may be experienced if this is
incorrectly set. If you cannot hear a dial tone
through your headset, turn the configuration
dial until you obtain it. Then:
1. Make a call with your desk telephone
and, while speaking to the recipient,
2. Turn the configuration dial through the 4
positions.
3. Select the position that provides the best
sound quality for both you and your
recipient.
4. During this call you should also adjust the
listen and speak volume as described on
page 8.
If you experience hissing/buzzing, or if
recipient can’t hear you or you can’t hear
them, repeat the steps above until you
achieve the best sound quality for both you
and the recipient. Once set, the configuration
dial will not require any further adjustment.
COMPATIBILITY WITH YOUR DESK TELEPHONE

6
PLT 510
PAIRING
PAIRING HEADSET AND BASE
The Voyager™ 510S Bluetooth® Headset System
is supplied with the headset and base unit
factory paired to each other. However, if you
have purchased a base unit separately, or if you
wish to use a replacement headset with your
existing base unit, the units must be paired as
follows:
1. On the base, press and hold both speak
volume fine adjust buttons until the blue talk/on
line indicator light and red power indicator light
(on the front of unit) start to flash.
2. On the headset, press and hold the listen
volume adjust + button and call control button
until the status indicator flashes red and blue.
3. Pairing is complete when the talk/on line
indicator on base illuminates solidly, and the
status indicator light on headset flashes blue.
Important: Make sure your headset is not
connected to any other Bluetooth device
when attempting to pair.
PAIRING HEADSET AND
MOBILE PHONE
Before using your headset for
the first time with your
Bluetooth mobile phone or
device, you must pair it with
that device. To pair, follow
these steps:
1. Turn on mobile phone. Place headset in pairing mode by
simultaneously pressing and holding listen volume adjust
button marked + (volume up) and call control button for 2
seconds. When status indicator light flashes red then blue,
release the buttons.
2. Use your phone’s menu to search for Bluetooth audio devices
and select “PLT 510” when it appears on the display.
Note: In some circumstances the pairing process can take
up to two minutes to complete.
3. When the phone display asks for a passkey, enter: 0000.
Status indicator flashes blue, once the headset is successfully
paired. If pairing fails, try again starting with Step 1.

7
A
B
PLACING A CALL
Desk telephone:
Lift phone receiver and then press the call
control button on either the headset (A) or
base unit (B). When you hear the dial tone,
dial number using telephone keypad. If you
do not obtain a dial tone, check that the
configuration dial is set correctly as
described on page 5.
To disconnect, press call control button on
headset or base, then hang up receiver.
Important: If your desk telephone has a
receive volume control, make sure it is set
no higher than mid-range. Too high a
setting could cause audio problems.
Mobile phone:
Dial using your mobile phone’s keypad or
voice- dialling (if supported by your phone).
To disconnect, press call control button
on headset.
Important: You will first need to pair the
headset to your mobile phone. Refer to the
pairing instructions on page 6.
ANSWERING A CALL
Desk telephone:
Lift the telephone’s receiver. Press the call
control button on either the headset (A) or
base (B) to answer the call. To disconnect,
press call control button on headset or base.
Mobile phone:
Press the call control button on the headset (A)
to answer the call. To disconnect, press call
control button on headset.
PLACING & ANSWERING A CALL

8
B
A
SPEAK VOLUME – HOW YOU
SOUND TO OTHERS
1. Adjust the speak volume fine adjust buttons (A)
until the level is comfortable for the recipient.
2. If larger change is needed, try different
settings (A–D) on the speak volume major
adjust switch (B) on bottom of base.
Note: This setting only adjusts the
headset speak level on calls placed
using the desk telephone and cannot
adjust the headset speak volume when
used with a mobile phone.
Important: Too high a speak volume
can cause audio quality problems.
Please refer to the Troubleshooting
section at the end of this guide.
MUTE BUTTON
To mute a call, short press (<1 second) the
power/mute button once. A tone will sound every
15 seconds while mute is on.
To take the call off mute, short press (<1 second)
the button again.
Important: Too long a press (>3 seconds)
will power off the headset.
VOLUME & MUTE
LISTEN VOLUME - HOW OTHERS
SOUND TO YOU
1. Adjust the listen volume adjust +/– button
(A) to a comfortable level.
2. If you cannot find a comfortable listen level,
try different settings (1–4) on the listen volume
major adjust switch (B) as shown until a
satisfactory sound level is experienced.
Note: This setting only adjusts the
headset listen level on calls placed using
the desk telephone and cannot adjust the
headset listen volume when used with a
mobile phone.
Important: Too high a listen volume can
cause audio problems. Please refer to
the Troubleshooting section at the end
of this guide.

9HANDSET LIFTER (OPTIONAL)
OFF
ON
OPERATION WITH THE HANDSET
LIFTER ACCESSORY
The Plantronics Handset Lifter is an accessory
that has two functions:
• To automatically notify you when an
incoming call is detected even when
you are away from your desk.
• To lift or replace the telephone handset
from its cradle even when you are away
from your desk.
SETTING UP THE HANDSET LIFTER
1. Plug lifter power cord into handset lifter jack
on base.
2. Set handset lifter on/off switch on base to
“on” (down) position.
When set to “on,” the base senses when the
headset has been removed or replaced in the
base, automatically activating lifter to answer
or end a call.
3. Position lifter under telephone receiver.
Tip: Remove only a tiny piece of mounting
tape backing to temporarily stick lifter into
position—you may need to move it!
4. Press call control button to activate lifter. Dial
tone should sound if receiver is raised high
enough. If necessary, adjust lifter height switch
or re-position lifter under receiver.
5. Use mounting tape to fix lifter in position.