Plantronics Voyager Legend User manual

Voyager Legend
User Guide

Contents
What's in the Box 3
Accessories 4
Headset Overview 5
Pairing 6
Pair first time 6
Pair another phone 6
Charge 7
Fit 8
Change the eartip 8
Wear on the left or right 8
The Basics 9
Make/Take/End Calls 9
Mute 10
Adjust the volume 10
Use sensors 10
Play or pause streaming audio 10
More Features 11
Voice alerts 11
Voice commands 11
Customize your headset 12
Multipoint 12
Specifications 13
2

Headset USB charge cable
AC charger
Foam eartip covers and
silicone eartips
What's in the Box
3

Sold separately.
1 2
3 4 5
6 7
1Portable charge case
2Desktop charge stand
3AC charger
4USB charge cable
5Car charge adapter
6Micro USB charge adapter
7Eartip kit (available in S, M, L)
Accessories
4

voice
Call button
Volume button
Headset LED (indicator light)
Power button
Magnetic charge port
Mute button
Voice button
Play/Pause button
Headset Overview
5

The first time you switch on your headset it begins the pairing process.
1Put the headset on and turn it on.
2While the headset LEDs are flashing red and blue, activate Bluetooth®on your phone and set it
to search for new devices.
•iPhONE
Settings > General > Bluetooth > On
•Android™Smartphones
Settings > Wireless & Networks > Bluetooth: On > Scan for Devices
NOTE Menus may vary by device.
3Select “PLT_Legend.” If your phone asks, enter four zeros (0000) for the passcode or accept the
connection.
4Once successfully paired, LEDs stop flashing red and blue and you hear “pairing successful.”
NOTE To enable caller name announcement, allow access to your contacts if your phone prompts
you.
After pairing your headset to your phone you may want to pair another or new phone.
1Switch on your headset then choose:
• Tap the Voice button and say “Pair mode,” or
•Press and hold the Call button until you hear “Pairing”
2While the headset LEDs are flashing red and blue, activate Bluetooth®on your phone and set it
to search for new devices.
3Select “PLT_Legend.” If your phone asks, enter four zeros (0000) for the passcode or accept the
connection.
4Once successfully paired, LEDs stop flashing red and blue and you hear “pairing successful.”
NOTE To enable caller name announcement, allow access to your contacts if your phone prompts
you.
Pairing
Pair first time
Pair another phone
6

Your new headset has enough power to pair and make a few calls before
charging is needed, though you may charge at any time.
1Align snap-fit magnetic areas of headset and USB cable.
2Attach cable to USB wall charger or laptop for 90 minutes. LEDs turn off once fully charged.
Charge
7

Change the eartip for a better fit.
1Push in eartip and rotate to the left to unlock it.
1
2
2
2Align new eartip into slot.
3Rotate it to the right to lock it into place.
1
2
2
To wear the headset on your other ear, rotate the boom upwards then twist it around so the
eartip is on the other side before lowering the boom.
2
1
3
Fit
Change the eartip
Wear on the left or right
8

voice
Answer a call
Choose:
• Put on the headset to answer call, or
• Say “answer” after call is announced, or
•Tap the Call button
Answer a second call
First, tap the Call button to end current call, then tap the Call button again to answer new
call.
End a call
Tap the Call button to end current call.
Reject a call
Choose:
• Take off the headset , or
• Say “ignore” after call is announced, or
•Press Call button for 2 seconds
Call back last call
Double-tap the Call button .
Voice dial (phone feature)
Press the Call button for 2 seconds, wait for phone prompt and then tell the phone to dial the
name of a stored contact.
Caller Announcement
When wearing your headset, you will hear the name of a contact calling you so you can decide
whether to answer or ignore the call.
An incoming caller name is announced:
• if your phone has the Phone Book Access Profile (PBAP)
• if you granted access to your contacts during pairing process
• if they are a stored contact
However, in the following situations, an incoming caller name is not announced:
• if you use the sensors to automatically answer a call while putting on your headset
The Basics
Make/Take/End Calls
9

• if the caller is unknown, unlisted, or blocked
During a call, you can mute the microphone.
Tap the Mute button. You will hear “mute on” confirmation. An alert repeats every 15 minutes
to remind you of microphone mute. Tap the Mute button again to open the microphone and
hear “mute off” confirmation.
Toggle the Volume button up (+) or down (–) during a call or while streaming audio.
Smart Sensors™technology in this headset recognizes if the headset is being worn and can
automatically perform time-saving functions.
Putting on your headset will:
• Answer an incoming call
• Transfer an active call from your phone
• Resume streaming audio
Taking off your headset will:
• Reject an incoming call
• Transfer an active call to your phone handset
• Pause streaming audio
• Lock the Call button to avoid accidental calls
Reset Sensors
You may need to reset the sensors if they are not working as expected.
1Test Wearing the headset, tap the Call button to test sensors.
A talk time voice alert means sensors are working. A tone means sensors need to be reset .
2Reset To reset the sensors, charge your headset and place on a flat non-metallic surface for
more than 10 seconds.
A 2-second press of the Play/Pause button will either pause or resume playback of
streaming audio.
NOTE You must pause your streaming audio before you:
• use your headset's voice commands
• initiate an outbound call with your headset (call back or voice dial)
NOTE If you power off the headset or go out of phone range while streaming audio, your headset will
not play/pause the stream upon reconnecting until you manually resume streaming with your phone.
Mute
Adjust the volume
Use sensors
Play or pause streaming
audio
10