Playcraft GLIDE-N-TWIST RV-1917 User manual

IMPORTANT NOTES: Read First
For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
GLIDE-N-TWIST RV
INSTALLATION INSTRUCTIONS
Rev B
5/9/2011
RV-1917
Page 1 of 4
NOTE: Glide-N-Twist Bend Right
shown. Other configurations will vary
slightly, but does not affect assembly.
Public Playground Safety, Publication #325 at www.cpsc.gov for the surfacing appropriate for the fall height of
the equipment or consult your surfacing supply representative.
(A) Use liquid thread lock (such as Loctite
®
) with all threaded hardware. Important: Liquid thread lock (prior to
curing) helps to eliminate the common problem of "thread seizure" in stainless steel hardware by serving as a
lubricant during assembly.
(B) Do not pour concrete until the equipment is completely assembled, leveled and plumbed. Concrete must be
allowed to cure completely before using the equipment (at least 72 hours).
(C) An appropriate energy absorbing safety surface is required under and around all playground equipment.
Loose fill protective surfacing is shown only as an example for the purpose of this assembly instruction. Other
surfacing material may vary in thickness and/or compression depths. See free publication - The Handbook for
FIGURE 1
Glide-N-Twist
Figure 1.1
See Footing Detail
Figure 1.2
See Footing Detail

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
GLIDE-N-TWIST RV
INSTALLATION INSTRUCTIONS
Rev B
5/9/2011
RV-1917
Page 2 of 4
18
12
"
470mm
30
12
"
774mm
Top View - Bend Left Footing Layout
Footing Detail
Step 1
Refer to Footing Layout and mark footing
hole locations. Dig (1) Ø 12" footing hole and
(1) 12" x 20" x 18" deep oval footing hole.
Refer to Footing Detail for depth and details.
* Footing depth must be adjusted to
compensate for the depth/thickness
requirements of selected safety surfacing.
See Section 06.1 of the Installation Manual.
** Height shown from finish grade to
mounting hole.
Top View - Bend Right Footing Layout
Optional Filter Fabric over
Pea Gravel (for drainage)
Concrete Footing
2b Stone, drain rock
Undisturbed Soil
Blocking, see
Installers Manual
LOOSE FILL SURFACING MATERIAL SHOWN:
9" compressed or 12" uncompressed depth.
Compressed depth shown. (See Note C)
Footing Anchor
(Top of Soil)
(Finish Grade)
27" *
686mm
18"
457mm
12"
305mm
20"
508mm
46
12
" **
1181mm
88
12
" **
2248mm
42
34
"
1086mm
64
716
"
1636mm
42
34
"
1086mm
64
716
"
1636mm

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
GLIDE-N-TWIST RV
INSTALLATION INSTRUCTIONS
Rev B
5/9/2011
RV-1917
Page 3 of 4
GLIDE-N-TWIST
LADDER
3/8" x 1" Button
Head Bolt
3/8" x 7/8" O.D.
Thick Washer
Figure 1.1
Step 3
Place Wave Glider Rails into footing hole and
attach to Glide-N-Twist Ladder as shown in
Figure 1.2. (See Notes A & B)
Step 4
Fully tighten all fasteners according to the
"TIGHTENING TORQUE FOR HARDWARE"
section of the Installation Manual.
Step 5
Plumb and level entire component. Pour
concrete into footing holes. Allow at least 72
hours to cure before using this equipment.
(See Note B)
Step 6
Place required protective surfacing under and
around Glide-N-Twist. (See Note C)
Step 2
Refer to Footing Detail and remove required Hole
Plugs. Place Glide-N-Twist Ladder into footing
hole and attach to post as shown in Figure 1.1.
(See Notes A & B)
Figure 1.2
3/8" x 5/8"
Barrel Nut
1/2" SAE Washer
3/8" x 1" O.D.
Washer
3/8" x 3/4"
Button Head Bolt
GLIDE-N-TWIST
LADDER
WAVE GLIDER RAIL

Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
GLIDE-N-TWIST RV
INSTALLATION INSTRUCTIONS
Rev B
5/9/2011
RV-1917
Page 4 of 4
GLIDE-N-TWIST BEND LEFT
Part # DESCRIPTION QTY
FS-1916-RLBL Wave Glider Rail Bend Left 2
FS-1917-RV Glide-N-Twist Ladder RV 1
4-9339042 Washer Flat 3/8" x 7/8" O.D. x .100" Thick 4
9103032-TR Bolt Button Head 3/8" x 3/4" 2
9103052-TR Bolt Button Head 3/8" x 1" 4
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick 2
9345002 Washer Flat SAE 1/2" 2
9443022-TR Nut Barrel 3/8" x 5/8" BH 2
GLIDE-N-TWIST BEND RIGHT
Part # DESCRIPTION QTY
FS-1916-RLBR Wave Glider Rail Bend Right 2
FS-1917-RV Glide-N-Twist Ladder RV 1
4-9339042 Washer Flat 3/8" x 7/8" O.D. x .100" Thick 4
9103032-TR Bolt Button Head 3/8" x 3/4" 2
9103052-TR Bolt Button Head 3/8" x 1" 4
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick 2
9345002 Washer Flat SAE 1/2" 2
9443022-TR Nut Barrel 3/8" x 5/8" BH 2
GLIDE-N-TWIST LADDER RV:
Shall be fabricated using 2.375" O.D. 11 gauge
steel tubing and 1.315" O.D. 12 gauge steel handle
and rungs with welded 1/4" thick steel mounting
brackets and 3/8" thick steel tabs. The
Glide-N-Twist Ladder RV shall have a multi-stage
baked-on powder coat finish.
WAVE GLIDER RAIL:
Shall be fabricated using 1.900" O.D. 11 gauge
steel tubing with welded 3/8" thick steel tab. The
Wave Glider Rail shall have a multi-stage baked-on
powder coat finish.
HARDWARE:
Shall be stainless steel, zinc/nickel plated or
galvanized as required to resist rust and corrosion.
Parts List Specifications
Periodically tighten all screws, bolts and nuts. A
periodic inspection of all parts is necessary. If a part
is broken or worn, replace immediately. For general
maintenance please refer to our Playground
Maintenance Manual.
Maintenance