Playcraft Terrace Climber 1240 User manual

IMPORTANT NOTES: Read First
For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
TERRACE CLIMBER
INSTALLATION INSTRUCTIONS
Rev E
9/25/2017
1240
Page 1 of 5
NOTE: R5 5' Terrace Climber shown.
Other configurations will vary slightly,
but does not affect assembly.
Section 1309 Half Wall
See Footing Detail
See Installation Manual
Figure 1.1
Public Playground Safety, Publication #325 at www.cpsc.gov for the surfacing appropriate for the fall height of
the equipment or consult your surfacing supply representative.
(A) Use liquid thread lock (such as Loctite
®
) with all threaded hardware. Important: Liquid thread lock (prior to
curing) helps to eliminate the common problem of "thread seizure" in stainless steel hardware by serving as a
lubricant during assembly.
(B) Do not pour concrete until the equipment is completely assembled, leveled and plumbed. Concrete must be
allowed to cure completely before using the equipment (at least 72 hours).
(C) Refer to Installation Manual for 1309 Half Wall installation instructions.
(D) An appropriate energy absorbing safety surface is required under and around all playground equipment.
Loose fill protective surfacing is shown only as an example for the purpose of this assembly instruction. Other
surfacing material may vary in thickness and/or compression depths. See free publication - The Handbook for
FIGURE 1
Terrace Climber

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
TERRACE CLIMBER
INSTALLATION INSTRUCTIONS
Rev E
9/25/2017
1240
Page 2 of 5
Step 1
Refer to Footing Layout and mark footing hole locations.
Dig (3) Ø 12" footing holes. Refer to Footing Detail for
depth and details.
IMPORTANT: For areas with soft soil conditions, larger
footings may be required. Additionally, half foot deck
heights will require 6" deeper footing holes.
* Footing depth must be adjusted to compensate for the
depth/thickness requirements of selected safety
surfacing. See Section 06.1 of the Installation Manual.
Footing Detail
Optional Filter Fabric over
Pea Gravel (for drainage)
Concrete Footing
Footing Anchor
Blocking, see
Installers Manual
2b Stone, Drain Rock
Undisturbed Soil
(Top of Soil)
(Finish Grade)
LOOSE FILL SURFACING MATERIAL SHOWN:
9" compressed or 12" uncompressed depth.
Compressed depth shown. (See Note D)
27" *
686mm
18"
457mm
12"
305mm

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
TERRACE CLIMBER
INSTALLATION INSTRUCTIONS
Rev E
9/25/2017
1240
Page 3 of 5
67
516
"
1709mm
57
716
"
1458mm
55
78
"
1420mm
39
516
"
999mm
47
916
"
1208mm
48" Deck Top View - Footing Layout
40
516
"
1024mm
47
12
"
1207mm
35
18
"
892mm
60" Deck Top View - Footing Layout
45"
1143mm
72"- 96" Deck Top View - Footing Layout

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
TERRACE CLIMBER
INSTALLATION INSTRUCTIONS
Rev E
9/25/2017
1240
Page 4 of 5
TERRACE
CLIMBER
3/8" x 1-1/4"
Button Head Bolt
3/8" x 1" O.D.
Washer
3/8" Lock Nut
3/8" x 1" O.D.
Washer
FIGURE 2
Step 3
Place Terrace Climber into footing holes and attach
to deck as shown in Figure 3. (See Note A)
FIGURE 3
Step 2
For 84" & 96" Terrace Climber Only
Attach Terrace Climber Leg to Terrace Climber as
shown in Figure 2. (See Note A)
TERRACE CLIMBER
LEG
1/4" x 3/4" Square Dr.
Tek Screw
1/4" x 3/4" Square Dr.
Tek Screw

Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
TERRACE CLIMBER
INSTALLATION INSTRUCTIONS
Rev E
9/25/2017
1240
Page 5 of 5
Parts List Specifications
Periodically tighten all screws, bolts and nuts. A
periodic inspection of all parts is necessary. If a part
is broken or worn, replace immediately. For general
maintenance please refer to our Playground
Maintenance Manual.
Maintenance
TERRACE CLIMBER R5:
Shall be fabricated using 1.660" O.D. 11 gauge
steel rails with welded 1.315" O.D. 12 gauge steel
rungs and 3/16" thick steel mounting plate.
The Terrace Climber R5 shall have a multi-stage
baked-on powder coat finish.
TERRACE CLIMBER LEG:
Shall be fabricated using 1.660" O.D. 11 gauge
steel tubing with welded 5/8" O.D. steel anchor. The
Terrace Climber Leg shall have a multi-stage
baked-on powder coat finish.
HARDWARE:
Shall be stainless steel, zinc/nickel plated or
galvanized as required to resist rust and corrosion.
TERRACE CLIMBER 48", 60" & 72"
Part # DESCRIPTION QTY
Varies Terrace Climber R5 1
9103062-TR Bolt Button Head 3/8" x 1-1/4" 4
9103072-TR Bolt Button Head 3/8" x 1-1/2" 2
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick 12
9413002 Nut Lock 3/8" 6
Step 4
Attach Half Walls to deck and finish attaching
Terrace Climber as shown in Figure 1.1.
(See Notes A & C)
NOTE: Use (2) 3/8" x 1-1/2" Button Head Bolts
included with Terrace Climber Assembly.
Step 5
Fully tighten all fasteners according to the
"TIGHTENING TORQUE FOR HARDWARE"
section of the Installation Manual.
Step 6
Plumb and level entire component. Pour concrete
into footing holes. Allow at least 72 hours to cure
before using this equipment. (See Note B)
Step 7
Place required protective surfacing under and
around Terrace Climber. (See Note D)
Figure 1.1
TERRACE CLIMBER 84" & 96"
Part # DESCRIPTION QTY.
Varies Terrace Climber R5 1
FS-1240-LEG Terrace Climber Leg 3
9103062-TR Bolt Button Head 3/8" x 1-1/4" 4
9103072-TR Bolt Button Head 3/8" x 1-1/2" 2
9271032 Screw Tek 1/4" x 3/4" PH SQDR 6
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick 12
9413002 Nut Lock 3/8" 6
3/8" Lock Nut
3/8" x 1" O.D.
Washer
3/8" x 1-1/2"
Button Head Bolt
3/8" x 1" O.D.
Washer
TERRACE
CLIMBER