Playcraft Multi-Section Inclined Crawl Tube R5-1500-3I User manual

IMPORTANT NOTES: Read First
For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
MULTI-SECTION INCLINED CRAWL TUBE
R5-1500-3I Thru 6I
Page 1 of 3
Rev B
(A) Use liquid thread lock (such as Loctite
®
) with all threaded hardware. Important: Liquid thread lock (prior to
curing) helps to eliminate the common problem of "thread seizure" in stainless steel hardware by serving as a
lubricant during assembly.
(B) Do not pour concrete until the equipment is completely assembled, leveled and plumbed. Concrete must be
allowed to cure completely before using the equipment (at least 72 hours).
(C) Refer to Installation Manual for R5-1601 Panel-Type1 (Rotomolded) Assembly and 1708 Tube Support
Assembly.
(D) Use appropriate compliant protective surfacing and adjust footing depths accordingly. See free publication -
The Handbook for Public Playground Safety, Publication #325 at www.CPSC.gov for the surfacing appropriate
for the fall height of the equipment or consult you surfacing supply representative.
(E) Note: The upper panel is typically raised 3" above the deck.
Gap between Panel
1708 Tube Support Assembly
See Installation Manual Sections
and deck must be
(See Note E)
less than 3½"
Multi-Section Inclined Crawl Tube
Assembly for
FIGURE 1
mount assembly.
Deck
Tube orientation will vary,
appropriate Tube orientations.
see Top View of structure for
Figure 1.1
Note
R5-1601 Panel-Type 1 (Rotomolded)
See Installation Manual Sections
Figure 1.2
:
See Installation Manual Sections
R5-1601 Panel-Type 1 (Rotomolded)
Assembly for Ground mount assembly.

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
MULTI-SECTION INCLINED CRAWL TUBE
Rev B
R5-1500-3I Thru 6I
Page 2 of 3
Figure 1.1
Figure 2
Figure 1.2
Support Orientation. Dig footing hole and attach Tube
Step 5
Section. Refer to the Top View of your structure for Tube
Installation Manual.
Support Assembly of the Installation Manual, Figure 1.2,
Support to Tube Section. (Refer to Section 1708 Tube
Panel - Type1 (Rotomolded) Assembly of the
(See Note D)
Attach Panels to posts/decks. Refer to R5-1601
under and around Inclined Crawl Tube.
Place appropriate compliant protective surfacing
Step 3
Note A and Note B)
Step 2
Fully tighten all fasteners according to the
"TIGHTENING TORQUE FOR HARDWARE"
section of the Installation Manual.
Step 6
(See Note A)
Attach Tube Sections as shown in figure 1.1. Refer to
your structure top view for appropriate orientation.
Step 4
Attach Tube Sections with Tube Support as shown in
figure 1.2.
Note: Tube Support required for every second Tube
Step 1
(Factory Assembled)
Attach Tube Section to Panel as shown in Figure 2.
(See Note A)
3/8" x 1" O.D. Washer
TUBE SUPPORT
Washer
Head Bolt
3/8" x 1-1/2" Button
Washer
3/8" x 1" O.D.
Washer
3/8" Lock Nut
CRAWL TUBE SECTION
CRAWL TUBE SECTION
3/8" Lock Nut
INCLINED
3/8" x 1" O.D.
3/8" x 1" O.D. Washer
3/8" x 1-1/4" Button Head Bolt
VERTICAL LEG
3/8" x 1" Button Head Bolt
3/8" x 1" O.D.
KEE CLAMP
Head Bolt
Washer
Washer 3/8" x 1-1/4" Button
3/8" x 1" O.D.3/8" Lock Nut
ROTO PANEL ROUND
3/8" x 1" O.D.
Molded-In Threaded Insert

Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
MULTI-SECTION INCLINED CRAWL TUBE
R5-1500-3I Thru 6I
Page 3 of 3
Rev B
Parts List
Specifications
Assembled Parts List
galvanized as required to resist rust and corrosion.
Shall be constructed of UV-stabilized, rotationally
average wall thickness of .250".
TUBES
Shall be stainless steel, zinc/nickel plated or
molded linear low density polyethylene with an
HARDWARE:
:
Part #
DESCRIPTION
Qty.
R5-1500-3I
3 Section
Qty.
R5-1500-4I
4 Section
Qty.
R5-1500-5I
5 Section
Qty.
R5-1500-6I
6 Section
VARIES Straight Crawl Tube Section 1 2 3 4
FS-1708-INCL Tube Support Inclined 1122
9103062-TR Bolt Button Head 3/8" x 1-1/4" 21 33 42 54
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick 42 66 84 108
9413002 Nut Lock 3/8" 21 33 42 54
Part # DESCRIPTION
Qty.
For all Multi-Section
Inclined Crawl Tubes
004639 Vertical Crawl Tube Elbow 30 Deg MF 1
004906 Vertical Crawl Tube Elbow 30 Deg MM 1
R5-1601 Panel Round R5 2
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick 24
9103052-TR Bolt Button Head 3/8" x 1" 24
Maintenance Manual.
Periodically tighten all screws, bolts and nuts. A
periodic inspection of all parts is necessary. If a part
is broken or worn, replace immediately. For general
maintenance please refer to our Playground
Maintenance