Playcraft Transition Wall 1310 User manual

IMPORTANT NOTES: Read First
www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or 541.955.9199 (International)
TRANSITION WALL
INSTALLATION INSTRUCTIONS
Rev J
8/19/2020
1310
Page 1 of 3
See Installation Manual
Sections 09 Collars
and 11 Clamps
Figure 1.1
Figure 1.2
(A) Use liquid thread lock (such as Loctite
®) with all threaded hardware.
Important: Liquid thread lock (prior to
curing) helps to eliminate the common problem of "thread seizure" in stainless steel hardware by serving as a
lubricant during assembly.
(B) Refer to Installation Manual for 09 Collars and 11 Socket Clamps assembly instructions.
(C) Use appropriate compliant protective surfacing and adjust footing depths accordingly. See free publication -
The Handbook for Public Playground Safety, Publication #325 at www.CPSC.gov for the surfacing appropriate
for the fall height of the equipment or consult you surfacing supply representative.
NOTE : R5 Single Tab Transition Wall
shown. Other configurations will vary
slightly but do not affect assembly.
FIGURE 1
Transition Wall

www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or 541.955.9199 (International)
TRANSITION WALL
INSTALLATION INSTRUCTIONS
Rev J
8/19/2020
1310
Page 2 of 3
3/8" Lock Nut
3/8" x 1" O.D. Washer
3/8" x 1-1/4"
Button Head Bolt
3/8" x 1" O.D.
Washer
Figure 1.1
See Table
FRONT ELEVATION
Figure 1.2
TRANSITION
WALL
SOCKET CLAMP
ASSEMBLY
Step 1
Locate and attach collars to posts at height shown in
Front Elevation. (See Note B)
* Height shown from top of deck to top of collar.
Step 3
Attach Transition Wall to posts using Socket Clamps
as shown in Figure 1.2. (See Note B)
Step 4
Fully tighten all fasteners according to the
"TIGHTENING TORQUE FOR HARDWARE"
section of the Installation Manual.
Step 2
Place Transition Wall Tabs into Deck slots and loosely
attach hardware as shown in Figure 1.1. (See Note A)
COLLAR HEIGHT *
Version Standard Metric
1310-R35/R5 39" 991mm
1310-R5 JAPAN 45" 1143mm

www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or 541.955.9199 (International)
TRANSITION WALL
INSTALLATION INSTRUCTIONS
Rev J
8/19/2020
1310
Page 3 of 3
TRANSITION WALL:
Shall be fabricated from 1.315" O.D. 12 guage steel
tubing, welded 1.029" O.D. 14 guage vertical rails
and handles and 1/2" thick steel tabs and will have
a multi-stage baked on powder coat finish.
SOCKET CLAMPS:
Shall be two-part and precision die-cast from a high
strength aluminum alloy and will have a multi-stage
baked on powder coat finish.
HARDWARE:
Shall be stainless steel, zinc/nickel plated or
galvanized as required to resist rust and corrosion.
R5 TRANSITION WALL
Part # DESCRIPTION QTY.
Varies Transition Wall R5 1
HS-1001-R5 Socket Clamp Set R5 2
9103062-TR Bolt Button Head 3/8" x 1-1/4" 2
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick 4
9413002 Nut Lock 3/8" 2
R3.5 TRANSITION WALL
Part # DESCRIPTION QTY.
Varies Transition Wall R3.5 1
HS-1001-R35 Socket Clamp Set R3.5 2
9103062-TR Bolt Button Head 3/8" x 1-1/4" 2
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick 4
9413002 Nut Lock 3/8" 2
Parts List Specifications
Periodically tighten all screws, bolts and nuts. A
periodic inspection of all parts is necessary. If a part
is broken or worn, replace immediately. For general
maintenance please refer to our Playground
Maintenance Manual.
Maintenance