Playcraft Poly Wave Slide Canada 1704-CAN User manual

IMPORTANT NOTES: Read First
For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
POLY WAVE SLIDE - CANADA
Rev B
7/18/2009
1704-CAN
Page 1 of 5
NOTE: R5 60" Configuration
shown. R3.5 will vary slightly, but
does not affect the assembly.
R5-1304 Slide Sit Down Wall or
R3.5-1304-CAN Sit Down
Figure 1.1
Wall R3.5 Canada
Figure 1.2
See Installation Manual Section
See Footing Detail
greater than 48". For slide elevations no greater than 48", the exit height shall be no greater than 11".
Exit region must also have a downward slope of 0 to 4°.
(A) Use liquid thread lock (such as Loctite
®
) with all threaded hardware. Important: Liquid thread lock (prior to
curing) helps to eliminate the common problem of "thread seizure" in stainless steel hardware by serving as a
lubricant during assembly.
(B) Do not pour concrete until the equipment is completely assembled, leveled and plumbed. Concrete must be
allowed to cure completely before using the equipment (at least 72 hours).
(C) Refer to Installation Manual Section R5-1304 Slide Sit Down Wall or R3.5-1304-CAN Slide Sit Down Wall
R3.5 Canada assembly instructions.
(D) Use appropriate compliant protective surfacing and adjust footing depths accordingly. See free publication -
The Handbook for Public Playground Safety, Publication #325 at www.CPSC.gov for the surfacing appropriate
for the fall height of the equipment or consult you surfacing supply representative.
(E) Exit height must be between 7" [180mm] and 15" [380mm] from finish grade for slides with an elevation
FIGURE 1
60" Poly Wave Slide

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
POLY WAVE SLIDE - CANADA
Rev B
7/18/2009
1704-CAN
Page 2 of 5
For areas with soft soil conditions, larger
See Section 06.1 of the Installation Manual
** Adjust footing depth with blocking to meet required slide
Footing Detail
Pea Gravel (for drainage)
Concrete Footing
Optional Filter Fabric Over
(welded 5/8" Rod)
2b Stone, drain rock
Undisturbed Soil
Footing Anchor
Installers Manual
Blocking, See
footings may be required.
exit height. (See Note E)
* Footing depth must be adjusted to compensate for the
depth/thickness requirements of selected safety surfacing.
(Top of Soil)
(Finish Grade)
Step 1
Refer to Footing Layout and mark footing hole locations.
Dig (1) Ø 12" and (1) 12" x 24" footing hole. Refer to
Footing Detail for depth and details.
Note: For 48" Poly Wave Slide dig only (1) 12" x 24"
footing hole.
IMPORTANT:
LOOSE FILL GROUND COVER:
Impact attenuating (resilient)
surfacing 9" compacted or
12" uncompressed depth
Compacted depth shown.
(See Note D)
LD1*
LD2**
See Note E
For Exit Height
SD1* SD2**
12"
305mm
12"
305mm
Footing Depth Dimensions
Support Support
Deck Height SD1* SD2** LD1* LD2**
42" NA NA 33" [838mm] 24" [610mm]
48" NA NA 27" [686mm] 18" [457mm]
54" 36" [914mm] 27" [686mm] 33" [838mm] 24" [610mm]
60" 30" [762mm] 21" [533mm] 27" [686mm] 18" [457mm]
66" 28 1/2" [724mm] 19 1/2" [495mm] 33" [838mm] 24" [610mm]
72" 22 1/2" [572mm] 13 1/2" [343mm] 27" [686mm] 18" [457mm]

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
POLY WAVE SLIDE - CANADA
Rev B
7/18/2009
1704-CAN
Page 3 of 5
24"
610mm
24"
610mm
24"
610mm
79
58
"
2022mm
1704-5 - 60" Poly Wave Slide
Footing Layout
42
1116
"
1084mm
104
18
"
2645mm
52
18
"
1324mm
127
1316
"
3247mm
1704-4 - 48" Poly Wave Slide
Footing Layout
1704-6 - 72" Poly Wave Slide
Footing Layout

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
POLY WAVE SLIDE - CANADA
Rev B
7/18/2009
1704-CAN
Page 4 of 5
POLY WAVE
Deck
Button Head Bolt
3/8" x 2-1/4"
Lock Nut
3/8"
SLIDE
3/8" x 1" O.D.
Washer
SINGLE SLIDE
SPACER
SINGLE
SUPPORT
SLIDE
Button Head Bolt
3/8" x 3/4"
Washer
3/8" x 1" O.D.
Hex Bolt
3/8 x 3/4"
Washer
3/8" x 1" O.D.
SLIDE LEG
POLY WAVE
SLIDE
Figure 1.1
Step 5
Fully tighten all fasteners according to the
"TIGHTENING TORQUE FOR HARDWARE"
section of the Installation Manual.
Step 6
Plumb and level entire component. Pour concrete
into footing hole. Allow at least 72 hours to cure
before using this equipment. (See Note B and E)
Step 7
Place appropriate compliant protective surfacing
under and around Poly Wave Slide. (See Note D)
Step 2
Attach the Slide Sit Down Wall to the deck and posts.
(See Note C)
Step 3
Attach the Slide Support and the Single Slide Leg to the
Poly Wave Slide as shown in Figure 1.1. (See Note A)
NOTE: Slide Support is for 60" and 72" Poly Wave
Slide only.
Step 4
Place the Poly Wave Slide in the footing hole(s) and
attach the Poly Wave Slide and Singe Slide Spacer to
the deck as shown in Figure 1.2.
(See Note A)
Figure 1.2

Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
POLY WAVE SLIDE - CANADA
Rev B
7/18/2009
1704-CAN
Page 5 of 5
Parts ListSpecifications
Periodically tighten all screws, bolts and nuts. A
periodic inspection of all parts is necessary. If a part
is broken or worn, replace immediately. For general
maintenance please refer to our Playground
Maintenance Manual.
Maintenance
SINGLE WAVE SLIDE:
Shall be constructed of UV-stabilized rotationally
molded linear low density polyethylene with an
average wall thickness of .250".
SINGLE SLIDE SPACER:
Shall be made from high density 3/4" hot extruded
polyethylene sheet plastic specially formulated for
optimum UV stability and color retention.
SINGLE SLIDE LEG:
Shall be fabricated of 1.660" O.D. 11 gauge steel
tubing welded onto a 10 gauge steel plate. The
Single Slide Leg has a multi-stage baked-on
powder coat finish.
SLIDE SUPPORT:
Shall be fabricated of 1.660" O.D. 11 gauge steel
tubing welded onto a 3/16" steel plate. The Slide
Support has a multi-stage baked-on powder coat
finish.
HARDWARE:
Shall be stainless steel, zinc/nickel plated or
galvanized as required to resist rust and corrosion.
60" Poly Wave Slide
Part # DESCRIPTION QTY.
DE-4227 Poly Wave Slide 5' High 1
EE-0009 Single Slide Spacer Canada 1
FS-1701 Single Slide Leg 1
FS-1704 Wave Slide Support 1
9103032-TR Bolt Button Head 3/8" x 3/4" 2
9103102-TR Bolt Button Head 3/8" x 2-1/4" 4
9123032 Bolt Hex 3/8" x 3/4" 4
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick 14
9413002 Nut Lock 3/8" 4
48" Poly Wave Slide
Part # DESCRIPTION QTY.
DE-4276 Poly Wave Slide 4' High 1
EE-0009 Single Slide Spacer Canada 1
FS-1701 Single Slide Leg 1
9103102-TR Bolt Button Head 3/8" x 2-1/4" 4
9123032 Bolt Hex 3/8" x 3/4" 4
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick 12
9413002 Nut Lock 3/8" 4
72" Poly Wave Slide
Part # DESCRIPTION QTY.
DE-4275 Poly Wave Slide 6' High 1
EE-0009 Single Slide Spacer Canada 1
FS-1701 Single Slide Leg 1
FS-1704 Wave Slide Support 1
9103032-TR Bolt Button Head 3/8" x 3/4" 2
9103102-TR Bolt Button Head 3/8" x 2-1/4" 4
9123032 Bolt Hex 3/8" x 3/4" 4
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick 14
9413002 Nut Lock 3/8" 4