Playcraft Stacked Loop Climber 1224 User manual

IMPORTANT NOTES: Read First
For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
STACKED LOOP CLIMBER
Rev D
12/16/2009
1224
Page 1 of 3
NOTE: R5 5' deck height shown.
Other configurations will vary slightly,
but will not affect assembly.
The Handbook for Public Playground Safety, Publication #325 at www.CPSC.gov for the surfacing appropriate
for the fall height of the equipment or consult you surfacing supply representative.
(A) Use liquid thread lock (such as Loctite
®
) with all threaded hardware. Important: Liquid thread lock (prior to
curing) helps to eliminate the common problem of "thread seizure" in stainless steel hardware by serving as a
lubricant during assembly.
(B) Do not pour concrete until the equipment is completely assembled, leveled and plumbed. Concrete must be
allowed to cure completely before using the equipment (at least 72 hours).
(C) Refer to Installation Manual for 1310 Transition Wall assembly instructions.
(D) Use appropriate compliant protective surfacing and adjust footing depths accordingly. See free publication -
FIGURE 1
Stacked Loop Climber
See Footing Detail
Figure 1.1
See Installation Manual
Section 1310 Transition Wall

For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
STACKED LOOP CLIMBER
Rev D
12/16/2009
1224
Page 2 of 3
24"
610mm
12"
304mm
surfacing. See Section 06.1 of the Installation Manual
Footing Detail
Step 1
Refer to Footing Layout and mark footing hole locations.
Dig (2) Ø 12" footing holes. Refer to Footing Detail for
depth and details.
IMPORTANT: For areas with soft soil conditions, larger
footings may be required. Additionally, half foot deck
heights will require 6" deeper footing holes.
* Footing depth must be adjusted to compensate for the
depth/thickness requirements of selected safety
Top View - Footing Layout
Installers Manual
Pea Gravel (for drainage)
Concrete Footing
Optional Filter Fabric over
(welded 5/8" rod)
Footing Anchor
2b Stone, Drain Rock
Undisturbed Soil
Blocking, see
(Top of Soil)
(Finish Grade)
LOOSE FILL GROUND COVER:
Impact attenuating (resilient) surfacing
9" compacted or 12" uncompressed depth
Compacted depth shown. (See Note D)
18"
457mm 686mm *27"
12"
305mm

Manufactured by Krauss Craft, Inc.
www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or
541.955.9199 (International)
STACKED LOOP CLIMBER
Rev D
12/16/2009
1224
Page 3 of 3
Maintenance Manual.
Periodically tighten all screws, bolts and nuts. A
periodic inspection of all parts is necessary. If a part
is broken or worn, replace immediately. For general
maintenance please refer to our Playground
Maintenance
Specifications Parts List
Part # DESCRIPTION QTY
Varies Stacked Loop Climber 1
9103032-TR Bolt Button Head 3/8" x 3/4" 4
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick 4
9345002 Washer Flat SAE 1/2" 4
9443022-TR Nut Barrel 3/8" x 5/8" BH 4
Plumb and level entire component. Pour concrete
into footing holes. Allow at least 72 hours to cure
before using this equipment. (See Note B)
Step 5
Place appropriate compliant protective surfacing
under and around Stacked Loop Climber.
(See Note D)
Step 2
Attach Transition Wall to deck. Place Stacked
Loop Climber into footing holes and attach to the
Transition Wall as shown in Figure 1.1.
(See Notes A & C)
Step 3
Fully tighten all fasteners according to the
"TIGHTENING TORQUE FOR HARDWARE"
section of the Installation Manual.
Step 4
STACKED LOOP CLIMBER:
Shall be constructed of 1.660" O.D 11 gauge steel
tubing and connecting rails with welded 1.315" O.D.
12 gauge steel tubing loops . The Stacked Loop
Climber has a multi-stage baked on powder coat
finish.
HARDWARE:
Shall be stainless steel, zinc/nickel plated or
galvanized as required to resist rust and corrosion.
3/8" x 3/4"
Barrel Nut
1/2" SAE Washer
3/8" x 1" O.D. Washer
3/8" x 5/8"
Button Head Bolt
TRANSITION WALL
STACKED LOOP
CLIMBER
Figure 1.1