Playskool Step Start Walk 'n Ride (2003) 05545 User manual

OVER 9 months - 36 months
05545
Step Start Walk ‘n Ride™
Step Start Walk ‘n Ride™
WARNING:
CAUTION:
Adult supervision required. This ride-on toy is not to be used near swimming
pools, on or near hills, roadways or stairways. Shoes must be worn at all
times when riding this toy. Designed for only one rider at a time.
This product contains small parts which are necessary for assembly. Prior to
and during assembly of this product, keep small parts out of children's reach.
Small parts pose a choking hazard to children under 3 years.
ADULT ASSEMBLY AND PHILLIPS/CROSS HEAD SCREWDRIVER (NOT INCLUDED)
REQUIRED.
MAXIMUM WEIGHT 42 LBS. (19 KGS.)
Parts include: body/chassis, 4 wheels, front handle, rear handle, handle retainer, dial,
roller, spinner (2 pieces), antenna, gear shift, 4 plain #6 screws, 1 #6 screw with
attached washer, and instructions.

ASSEMBLY:
11..AAttttaacchhWWhheeeellss
Tip body/chassis on its side. Snap wheel onto axle,
with flat side of wheel against chassis. Repeat for
remaining 3 wheels.
22..AAsssseemmbblleeHHaannddlleess
To snap front and rear handles together: Place rear
handle upside down on flat surface. Holding front
handle with back facing rear handle and perpendicular
to rear handle, snap posts on front handle into holes in
rear handle.
33..AAttttaacchhHHaannddlleeAAsssseemmbbllyyttooBBooddyy
Lift body and remove cardboard insert.
Turn body/chassis on its side. Insert front handle
through slot in body.
WHEEL
CHASSIS
FRONT HANDLE
REAR HANDLE
BODY
CARD-
BOARD
INSERT
FRONT
HANDLE
SLOT
Fit axle on rear handle into ridges in underside of body.
Place handle retainer over axle (retainer fits only one
way). Using the 4 plain #6 screws and Phillips/cross
head screwdriver, attach retainer to body.
NOTE: If body is locked closed, see back panel for
conversion instructions.
AXLE
RIDGES
SCREWS HANDLE
RETAINER

44..DDiiaall
With body/chassis on its side, insert dial into recess.
Turn body so that underside of chassis faces you.
Insert #6 screw with attached washer into hole, and
tighten with Phillips/cross head screwdriver.
55..RRoolllleerr
Turn body/chassis right side up and lower chassis onto
body. Insert posts on roller into holes in recessed area
(smaller post into smaller hole, larger post into larger
hole).
66..AAnntteennnnaa
Antenna fits only one way. Insert end of antenna into
hole.
SCREW
HOLE
DIAL
RECESSED
AREA
ROLLER
SPINNER
RECESSED
AREA
ANTENNA
HOLE
77..GGeeaarrSShhiifftt
Gear shift fits only one way. Inserts posts on gear shift
into holes in recessed area (smaller post into smaller
hole, larger post into larger hole).
88..SSppiinnnneerr
Slide slots on each spinner piece into each other until
they snap into place. Snap assembled spinner into
recessed area.
GEAR SHIFT
RECESSED
AREA
SPINNER
PIECE

Product and colors may vary.
© 2003 Hasbro, Inc. All Rights Reserved.
® denotes Reg. U.S. Pat. & TM Office.
U.S. Patent Nos. 6,296,268 & D424,126 05545 P/N 6257540200
FUNCTION:
NNOOTTEE::UUppoonnccoommpplleettiinnggaasssseemmbbllyy,,tthheettooyywwiillllpprroobbaabbllyybbeeiinntthheerriiddee--oonnmmooddee..
••TTooCCoonnvveerrttFFrroommRRiiddee--OOnnTTooWWaallkkeerr::
Lift toy to access underside of chassis. Squeeze latch
with one hand, and at same time, grasp rear handle and
lift up body.
Push handle down to lock into place - latch must be
visible to lock in place (listen for click).
Make sure the handle locks into place.
••TTooCCoonnvveerrttFFrroommWWaallkkeerrTTooRRiiddee--OOnn::
Squeeze latch on top of chassis. Lift rear handle up and
forward. Rotate handles up then lower body onto
chassis.
Make sure the handle locks into place.
LATCH
LATCH
LATCH
PLAYSKOOL.COM
FOR NEW PRODUCTS AND OFFERS
PLAYSKOOL.COM
FOR NEW PRODUCTS AND OFFERS
Questions? Call: 1-800-PLAYSKL