pleasant hearth ZCB100 User manual

1
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
IMZCB - 2018-12-11
Zero Clearance Blower
MODEL #: ZCB100
Questions, problems, missing parts?
Before returning to your retailer, call our call our customer service depart-
ment at 1-877-447-4768, 8:30 a.m. – 4:30 p.m., CST, Monday – Friday or
email us at [email protected].
IMPORTANT INSTRUCTIONS
PLEASE READ THIS MANUAL BEFORE INSTALLING AND USING APPLIANCE
WARNING: IF THE INFORMATION IN THIS MANUAL IS NOT
FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT
CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF
LIFE.
WARNING: THIS PRODUCT IS ONLY FOR USE WITH MODELS
SPECIFIED IN THIS MANUAL BY THE MANFACTURER. ANY OTHER
USAGE OR INSTALLATION NOT SPECIFIED IN THIS MANUAL IS
PROHIBITED.
WARNING
This Product can expose you to chemicals including Diisononyl phthalate (DINP) which is known
to the State of California to cause cancer and Di-isodecyl phthalates (DIDP) which is known to the
State of California to cause developmental harm.
For more information go to www.p65Warnings.ca.gov

2

3
If you are installing the forced air kit on PHZC32C, PHZC36C, and PHZC42C models, see the installation instructions provided with the kit
for electrical wiring requirements, or the blower installation section. The firebox must be connected to main power supply at time of
firebox installation. The blower should be installed prior to the installation of the vent-free heater but can be installed after installation if the
electrical connections have already been installed. The electrical connections must be made before the firebox is framed and enclosed in
the finished walls.
WARNING!
Electrical connections should only be performed by a quali-
fied, licensed electrician, main power must be off when
connecting to
main electrical power supply or performing service.
The blower when installed, must be electrically grounded
in accordance with local codes or in the absence of local
codes, with the National Electrical Code ANSI/NFPA 70.
Fig. - Optional Blower Installation
Optional ZCB100 Blower Kit
Blower Mounting Bracket
Electrical Box
Lower Grill Assembly
(4) #8 Sheet Metal Screws
(4) Sheet Metal Screws
Included in Blower Kit
Figure 15 - Optional Blower Installation
Blower Installation Instructions:
1. Lower the bottom grill assembly and remove the
blower mounting bracket attached to the inner back
wall of the firebox with a #2 phillips screw driver.
2. Attach the blower to the bracket with the (4) sheet
metal screws included int he blower kit as shown in
Figure 15.
3. Re-install the bracket insuring the blower outlet is
pointed upward.
4. Plug in the cord to the properly grounded 3-prong
receptacle.
WARNING!
Never use an extension cord to power the blower.
1
1
2
2
A A
B B
ZCF-5060
GHP Group Inc.
6440 W Howard St., Niles, IL 60714
DRAWN
DanDowning
CHECKED
APPROVED
A
2/14/2018
SIZE
TITLE
REV
X.XXX = +/- 0.005"
X.XX = +/- 0.010"
X.X = +/-0.100"
ANGLES = +/- 2 Deg.
MATERIAL
DWG NO
SCALE
TOLERANCES
WIRING DIAGRAM
POWER CORD / CABLE DE ENERGIA
MOTOR / MOTOR
BLACK / NEGRO
GREEN / VERDE
WHITE / BLANCO
IF ANY ORIGINAL WIRING SUPPLIED
WITH THIS HEATER MUST BE REPLACED,
IT MUST BE TYPE AWG 105C WIRE OR ITS
EQUIVALENT EXCEPT AS INDICATED.
SI SE DEBE REEMPLAZAR UN CABLEADO
ORIGINAL PROVIEIDO CON EL CALENTADOR,
DEBE SER CABLE TIPO AWG 105C O SU
EQUIVALENTE, EXCEPTO SI SE INDICA DE
OTRA MANERA.
EARTH (SHELL)
TIERRA (CUBIERTA)
WIRING DIAGRAM
ZCF FIREBOX BLOWER
PLEASANT HEARTH ZERO CLEARANCE FIREBOXES
BLOWER INSTALLATION

4
PLEASANT HEARTH GAS FIREPLACE INSERTS
BLOWER INSTALLATION
1. Remove top grill (if frame is not already removed).
XSEC0004-XSEC0004SECTION
2
3. Assemble Fan and the removed bracket together by
screwing x4 screws into the top of the bracket.
CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can
cause improper and dangerous operation.
Verify proper operation after servicing.
NOTE: If any of the original wire as supplied with the appliance must be replaced, it must be
replaced with a wire of at least an equal temperature rating.
2. Remove bracket from top vent by unscrewing x4 screws
XSEC0004-XSEC0004SECTION
3
NOTE: Installation may require two people.
1
Screws

5
5
4. Reinsert fan and bracket assembly into the Top Vent
and screw in x 4 screws into the back of the replace
cabinet.
XSEC0004-XSEC0004SECTION
BLOWER MOUNTING LOCATION
4
Screws
5. Route the fan cable through the race way.
Note: Junction box needs an outlet installed.
6
6. Reassemble top grill (if frame is not already
removed).
INSTALLATION
BLOWER
SOPLADOR
BLACK/NEGRO
WHITE/BLANCO
GREEN/VERDE
BLOWER WIRING DIAGRAM
Install a NEMA 5-15R
receptacle for power supply
IF ANY ORIGINAL WIRING SUPPLIED
WITH THIS HEATER MUST BE
REPLACED, IT MUST BE TYP AWG
105C WIRE OR ITS EQUIVALENT
EXCEPT AS INDICATED.
SI VOUS DEVEZZ FAIRE REMPLACER
LES FILS D’ORIGINE DU RADIATEUR,
PROCUREZ-VOUS DU FIL AWG 105C
OU L’EQUIVELENT SAUF INDICATION
CONTRAIRE.

5
WARNING: This appliance is equipped with a three-prong (grounding) plug for
your protection against shock hazard and must be plugged directly into a properly
grounded three-prong receptacle.
1. Read all instructions before using this appliance.
2. If possible always unplug this appliance when not in use.
3. Do not operate any heater with a damaged cord or plug or after the appli-
ance malfunctions, has been dropped or damaged in any manner.
4. Undernocircumstancesshouldthisappliancebemodied.Partshavingto
be removed for servicing must be replaced prior to operating this appliance
again.
5. Do not use outdoors.
6. This heater is not intended for use in bathrooms, laundry areas and similar
indoor locations. Never locate this appliance where it may fall into a bath-
tub or other water container.
7. Do not run cord under carpeting. Do not cover cord with throw rugs, run-
nersorthelike.Arrangecordawayfromtrafcareasandwhereitwillnot
be tripped over.
8. To disconnect this appliance, turn controls to the off position, then remove
plug from outlet.
9. Connect to properly grounded outlets only.
10. This appliance, when installed must be electrically grounded in accordance
with local codes, with the current USA installations, or in the absence of lo-
calcodes,theNationalElectricCode,ANSI/NFPANo.70.
11. Do not insert or allow foreign objects to enter any ventilation or exhaust
openingasthismaycauseanelectricshock,reordamagetheappliance.
12. Topreventpossiblere,donotblockairintakesorexhaustinanymanner.
13. Use this appliance only as described in this manual. Any other use not
recommendedbythemanufacturermaycausere,electricshockorinjury
to persons.
14. Installationandrepairshouldbedonebyaqualiedserviceperson.The
appliance should be inspected before use and at least annually by a pro-
fessional service person. More frequent cleaning may be required due to
excessive lint from carpeting, bedding material, etc. It is imperative that
control compartments, burners and circulating air passageways of the ap-
pliance be kept clean.
SAFETY INFORMATION SAVE THESE INSTRUCTIONS

6
PACKAGE CONTENTS
REF # PART # DESCRIPTION QUANTITY
A XB002-01Q Blower 1
B M4.2×8 Screw 4
Parts List
Before beginning assembly of product, make sure all parts are present.
Compare parts with package contents list and diagram under. If any part is
missing or damaged, do not attempt to assemble, install or operate the product.
Contact our Technical Service Department at 1-877-447-4768.
A
B
•APhillipsheadscrewdriverisneededforinstallation.

7
MAINTENANCE OF MOTORS
Always disconnect the appliance from the main power supply and allow it to
cool before any servicing operation. The motor used on the ame blower is pre-
lubricated for extended bearing life and requires no further lubrication. However,
periodic cleaning/vacuuming of the appliance around the air intake and exhaust,
as well as the blower is recommended. For heavy or continuous use, periodic
cleaning must be done more frequently. If the heater blows alternating cold and
warm air, check the blower for free movement and for debris restricting air ow.
If the blower does not move freely, the unit must be turned off and the blower
replaced immediately in order to prevent further damage to the unit.
WARNING: Make sure all power to the appliance is turned OFF
before proceeding.
PrintedinChina
Troubleshooting
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Blower is not
spinning.
Blower is
making a loud
noise.
1. There is no power to
the blower.
2. Blower motor is bad.
1. Blower housing or
blades are dirty.
2. Blower rotation is
blocked.
3. Defective blower.
1. Clean blower and blower
housing.
2. Verify wiring is not in blower
path.
3. Replace blower.
1. Allow 5-10 minutes for blower
to engage.
2. Replace blower.
This product includes a warranty against any defect in materials and
workmanship for a period of one (1) year from the date of retail sale. Contact our
Consumer Warranty Dept. for more information [phone].

8
PrintedinChina
33
This limited warranty is extended to the original retail purchaser of this heater and warrants against any
2
2
two
two
years
years

9
34
GHP Group, Inc.
6440 W Howard St
Niles, IL 60714-3302
Tel: [phone]
www.ghpgroupinc.com
GHP Group, Inc.
6440 W Howard St
Niles, IL 60714-3302