PNY Quadro FX Series User manual

PNY Quadro User Manual Rv. 0619 - V. 3.0 page 1
PNY Quadro
Professional Graphics Accelerators
User Manual
Quadro FX Series
Quadro NVS Series
PNY Technologies, Inc.
299 Webro Road
Parsippany, NJ 07054 (USA)
PNY Technologies Europe
Z.A.C du Phare
Rue Joseph Cugnot, BP-181
33708 Merignac Cedex (France)

PNY Quadro User Manual Rv. 0619- V.4.0 page 2
Table of Contents
Chapter 1 - Introduction................................................... 3
Chapter 2 - Hardware Installation................................... 6
Chapter 3 - Software Installation................................... 20
Chapter 4 - nView™ Installation ................................... 22
Chapter 5 - Display Properties....................................... 34
Chapter 6 - MAXtreme................................................... 63
Chapter 7 - POWERdraft............................................... 65
Chapter 8 - Technical Support / Warranty.................... 67
Limited Liability
The information contained in this manual has been validated at the time of manual production. The manufacturer
reserves the right to make any changes, additions and revisions to the product described in this manual at any time and
without notice. Consequently, PNY Technologies, Inc. assumes no liability for damages incurred directly or indirectly
from errors, omissions or discrepancies between the product and the manual.
Copyright and Trademarks
Copyright ©2006 PNY Technologies, Inc. All Rights Reserved. PNY, PNY Technologies and the PNY logo are
registered trademarks of PNY Technologies, Inc. NVIDIA, the NVIDIA Logo and NVIDIA Quadro are trademarks or
registered trademarks of NVIDIA Corporation in the United States and/or other countries. All other trademarks & logos
are the property of their respective companies.

PNY Quadro User Manual Rv. 0619- V.4.0 page 3
Chapter 1
Introduction
Congratulations on the purchase of your Quadro graphics accelerator board from PNY Technologies. You are now the
owner of a state-of-the-art graphics accelerator that was designed for professional 3D and 2D applications, and offers
features and functionality beyond any other card in its class. We recommend that you read through this User Guide before
installing your accelerator board to ensure a proper installation.
Minimum System Requirement
•IBM® or 100% PC compatible with genuine Pentium® III or AMD Athlon® class processor or higher
•One available PCI-Express slot, or one available PCI slot
•Windows®2000, Windows®XP or Windows®XP 64 with latest Service Pack or Linux
•256 MB system memory
•80 MB of available disk space for full installation
•CD-ROM or DVD-ROM drive
•VGA or DVI-I compatible monitor
Package Contents

PNY Quadro User Manual Rv. 0619- V.4.0 page 4
Please check your package, which contains the items below. If you find any damaged or missing items, please contact your
dealer.
•Graphics board
•1x DVI-I to VGA adapter (PNY Quadro FX 350, Quadro FX 540)
•2x DVI-I to VGA adapters (PNY Quadro FX 550, Quadro FX 560, Quadro FX1400, Quadro FX 1500, Quadro
FX 3450, Quadro FX 3500, Quadro FX4500, Quadro FX 4500G, Quadro FX 5500, Quadro FX 5500G)
•4x DVI-I to VGA adpaters (PNY Quadro FX 4500 X2)
•1x DMS59 adapter to 2x VGA + 1x DMS59 adapter to 2x DVI-I (PNY Quadro NVS 280, Quadro NVS 285)
•2x DMS59 adapters to 2x VGA + 2x DMS59 adapter to 2x DVI-I (PNY Quadro NVS 440)
•Additional Power Supply cable (PNY Quadro FX 3450, Quadro FX 3500, Quadro FX 4500, Quadro FX 4500G,
Quadro FX4500X2, Quadro FX 5500, Quadro FX 5500G)
•CD-ROM: software drivers for Windows® 2000, Windows® XP, Windows® XP 64 and Linux® 32/64
•Installation Guide

PNY Quadro User Manual Rv. 0619- V.4.0 page 5
Before You Begin
•Before installing the Display driver, make sure your Windows®2000, Windows® XP or Windows® XP 64 was
installed in VGA mode and functions properly.
IMPORTANT
Uninstalling Your Existing VGA Driver
•Remove your existing Display Driver using the Add/Remove Icon in ‘Control Panel’
•Shut down your computer.
•Remove your existing video card
•NOTE: If your system (motherboard) has an onboard graphics controller, please contact the system vendor on
how to properly disable it.

PNY Quadro User Manual Rv. 0619- V.4.0 page 6
Chapter 2
Hardware Installation
IMPORTANT
Static electricity can severely damage electronic parts.
Please take these precautions when installing your graphics card:
•Before touching any electronic parts, discharge the static electricity from your body by touching the
internal metal frame of your computer while it is unplugged.
•Do not remove a card from the anti-static container it shipped in until you are ready to install it.
Whenever you remove a card from your computer, always make sure to place it back in its container.
•Do not let your clothing touch any electronic parts.
•When handling a card, hold it by its edges, and avoid touching its circuitry.
Preparing Your Computer for Installation
Prior to working on your computer, make sure the power of the computer and any attached equipment such as
a monitor or printer is turned off. Unplug your computer and remove the cover. Remove your current graphics
card. For systems with ‘On-Board 3D Graphics’, there is no graphics card to remove. Some systems may
require you to disable your ‘On-Board 3D Graphics’. Consult your PC users’ manual or vendor manual on how
to properly do this.

PNY Quadro User Manual Rv. 0619- V.4.0 page 7
Selecting the Proper Expansion Slot
Most computers have a combination of PCI-Express x16, PCI-Express x8, PCI-Express x4, PCI-Express x1 and PCI
expansion slots. All these slots may look similar at first; however you will notice their differences once you examine them
more closely. The PCI-Express slots on your computer motherboard are usually the closest connectors to the CPU. The PCI
connectors are usually the farthest connector to the CPU. The PCI connectors are made from a white plastic, and are the
same connector type that most Sound or Modem Cards are connected. If you are still unsure which connectors PCI-Express
and PCI, consult your system manual to help you identify them. Plugging your graphics card into an incorrect slot could
damage the card, your computer, or both. Do not try to force a card into a slot that does not accommodate it, as it is
probably the wrong slot.
PNY Quadro Boards list by expansion slots to be used:
PCI-Express x16 PCI-Express x1, x4, x8 PCI
PNY Quadro NVS 285 PCIE x16 PNY Quadro NVS 285 PCIE x1 PNY Quadro NVS 280 PCI
PNY Quadro NVS 440 PCIE x16 PNY Quadro NVS 440 PCIE x1 PNY Quadro G-Sync
PNY Quadro FX 350 PNY Quadro G-Sync
PNY Quadro FX 540
PNY Quadro FX 550
PNY Quadro FX 560
PNY Quadro FX 1400
PNY Quadro FX 1500
PNY Quadro FX 3450
PNY Quadro FX 3500
PNY Quadro FX 4500
PNY Quadro FX 4500X2
PNY Quadro FX 5500
PNY Quadro G-Sync
The diagram below should help you in identifying the proper slot.
Motherboard Example with PCI-Express
PCI-Express x16 Slot
PCI-Express x1 Slots (3)

PNY Quadro User Manual Rv. 0619- V.4.0 page 8
Inserting Your Graphics Card
Remove the back of the PC cover for the slot you intend to use and save the screw for the mounting bracket of
your new PNY Quadro graphics card. Position the Quadro graphics card over the expansion slot that coincides
with the type (PCI-Express or PCI) of card purchased. Push the card firmly and evenly until it’s fully seated
into the slot. Replace the screw to secure the bracket of the graphic’s card to the computer chassis. Replace the
cover of your computer.
Plug your Monitor (CRT) or Flat Panel (TFT) Display cable into the appropriate connector on your graphic
card. All cables MUST be connected before your computer is powered on.

PNY Quadro User Manual Rv. 0619- V.4.0 page 9
Additional Power Requirements (PNY Quadro FX 3450, FX 3500, FX4500, FX 4500G, FX 4500X2,
FX 5500, FX 5500G cards)
In order for your Quadro FX graphics card to work optimally, an additional power connector (two for the
FX 4500X2) must be plugged in. Locate an unused power plug inside your computer system and plug it into
the card connector as shown below. The power connector is keyed so that it can only be inserted one way. PCI-
Express graphics cards needs PCI-Express power connectors. (Figure 1)
Please verify the orientation of the plug before insertion.
DO NOT FORCE IT INTO THE CONNECTOR.

PNY Quadro User Manual Rv. 0619- V.4.0 page 10
PNY Quadro NVS 280, NVS 285 Connectors
The PNY Quadro NVS 280 and NVS 285 have a single DMS59-pin connector. Each DMS59 connector can
support two monitors, using the supplied splitter cable (VGA or DVI-I).
DMS59-
p
in connecto
r

PNY Quadro User Manual Rv. 0619- V.4.0 page 11
PNY Quadro NVS 440 Connectors
The PNY Quadro NVS 440 has two DMS59-pin connectors. Each DMS59 connector can support two
monitors, using the supplied splitter cable (VGA or DVI-I).
DMS59-
p
in connecto
r
DMS59-
p
in connecto
r

PNY Quadro User Manual Rv. 0619- V.4.0 page 12
PNY Quadro FX 350 Connectors
The PNY Quadro FX350 has both VGA (analog) and DVI-I (digital) connectors. These connectors support:
•Single analog monitor
•Dual analog monitors (using one DVI-I to VGA adapter)
•Single digital monitor
•One analog monitor and one digital monitor
DVI-I Connector
V
GA Connecto
r

PNY Quadro User Manual Rv. 0619- V.4.0 page 13
Quadro FX 540 Connectors
The Quadro FX 540 has VGA, DVI-I & HDTV out connectors and supports dual monitors. These connectors
support:
•Single analog monitor
•Dual analog monitors (using one DVI-I to VGA adapter)
•Single digital monitor
•One analog monitor and one digital monitor
•The Quadro FX 540 also supports HDTV monitors
V
GA Connecto
r
HDTV output
DVI-I Connecto
r

PNY Quadro User Manual Rv. 0619- V.4.0 page 14
PNY Quadro FX 550 Connectors
The PNY Quadro FX 550 has dual DVI-I (digital) connectors. These connectors support:
•Single analog monitor (using one DVI-I to VGA adapter)
•Dual analog monitors (using two DVI-I to VGA adapter)
•Single digital monitor
•One analog monitor and one digital monitor (using one DVI-I to VGA adapter)
•Dual digital monitors
DVI-I Connector
DVI-I Connector

PNY Quadro User Manual Rv. 0619- V.4.0 page 15
PNY Quadro FX 1400, FX 3450, FX 3500, FX 4500 and FX 5500 Connectors
The PNY Quadro FX 1400, FX 3450, FX 3500, FX 4500 and FX 5500 have dual DVI-I connectors. These
connectors support:
•Single analog monitor (using one DVI-I to VGA adapter)
•Dual analog monitors (using two DVI-I to VGA adapter)
•Single digital monitor
•One analog monitor and one digital monitor (using one DVI-I to VGA adapter)
•Dual digital monitors
•The Quadro FX 1400, FX 3450, FX 3500, FX 4500 and FX 5500 also supports stereo out through a
standard 3-pin connector for 3D-shutter-glasses
DVI-I Connecto
r
Stereo 3D Connector
DVI-I Connector

PNY Quadro User Manual Rv. 0619- V.4.0 page 16
PNY Quadro FX 560 and FX 1500 Connectors
The PNY Quadro FX 560 and FX 1500 have dual DVI-I connectors. These connectors support:
•Single analog monitor (using one DVI-I to VGA adapter)
•Dual analog monitors (using two DVI-I to VGA adapters)
•Single digital monitor
•One analog monitor and one digital monitor (using one DVI-I to VGA adapter)
•Dual digital monitors
•The Quadro FX 560 and FX 1500 also supports HDTV monitors
DVI-I Connecto
r
HDTV output
DVI-I Connecto
r

PNY Quadro User Manual Rv. 0619- V.4.0 page 17
PNY Quadro FX 4500G and FX 5500G Connectors
The PNY Quadro FX 4500G and FX 5500G have dual DVI-I, one BNC and two RJ45 connectors. These
connectors support:
•Single analog monitor (using one DVI-I to VGA adapter)
•Dual analog monitors (using two DVI-I to VGA adapter)
•Single digital monitor
•One analog monitor and one digital monitor (using one DVI-I to VGA adapter)
•Dual digital monitors
•The Quadro FX 4500G, FX5500G also supports stereo out through a standard 3-pin connector for
3D-shutter-glasses
•Framelock: two RJ45 connectors
•Genlock: one BNC connector
DVI-I Connecto
r
DVI-I Connecto
r
Stereo 3D Connecto
r
RJ45 Connector
RJ45 Connector
BNC Connector

PNY Quadro User Manual Rv. 0619- V.4.0 page 18
PNY Quadro FX 4500X2 Connectors
The PNY Quadro FX 4500X2 has four DVI-I connectors. These connectors support:
•Single digital or analog monitor (using one DVI-I to VGA adapter)
•Dual digital or analog monitors (using two DVI-I to VGA adapters)
•Quad digital or analog monitors (using four DVI-I to VGA adapters)
•One or thee digital monitors and thee or one analog monitors (using one or three DVI-I to VGA
adapters)
•The Quadro FX 4500X2 also supports stereo out through a standard 3-pin connector for 3D-shutter-
glasses
DVI-I Connecto
r
DVI-I Connecto
r
Stereo 3D Connecto
r
DVI-I Connector
DVI-I Connector

PNY Quadro User Manual Rv. 0619- V.4.0 page 19
Chapter 3
Software Installation
Did you Uninstall your existing VGA driver?
•If yes, proceed with Chapter 3.
•If No, go back to Chapter 1 ‘Uninstalling Your VGA Driver’, complete the process and then continue with
Chapter 3.
Installing the Standard Graphics Adapter (VGA) Driver.
•Power up your computer and launch Windows® 2000, Windows® XP or Windows® XP 64.
•The Building Driver Database dialog box will appear as the Windows® operating system builds the database.
•When the Add New Hardware Wizard appears, click Next.
•Choose Search For The Best Driver For Your Device, and click Next.
•Make sure that all of the four choices are left blank. If not, un-check the applicable box. Then click Next.
•Windows® is now ready to install the Standard Graphics Adapter driver. Click Next to continue.
•Click Finish. Windows® will install the Standard Graphics Adapter driver.
•You will now be prompted to re-start your computer. Click Yes.

PNY Quadro User Manual Rv. 0619- V.4.0 page 20
Installing Quadro Graphics Drivers
1. Insert the PNY Quadro CD-ROM into the CD-ROM or DVD-ROM drive. The CD menu will pop up
automatically if auto start is enabled. Otherwise start the CD with a double click on the file
”Launch.exe”.
2. To install DirectX drivers for Windows® 2000/XP clicks on “Install Drivers and Tools” and choose
“DirectX”. Follow the screen instructions.
3. To install graphics card drivers for Windows® 2000, Windows® XP or Windows® XP 64 clicks on
“Install Drivers and Tools” and choose “Graphics Card Driver”. Follow the screen instructions.
4. After installing the graphics card drivers, restart the system.
5. Adjust desired resolution and refresh rates.
6. Besides this you should adjust the OpenGL settings according to the used application. Click on
“Start” / “Control Panel” / “Display” / “Settings” / “Advanced” / “Quadro …” and choose
“OpenGL Settings”. Here you find “Custom OpenGL Applications Settings”. Select the
application for which you want to load predetermined, optimized settings.