Point Source Audio Embrace EO-8WR User manual

®
EO-8WR
Earmount Microphone
With Dual Lavalier
Owner’s Manual
Product Warranty
Point Source Audio (PSA) products purchased in the
U.S.A. are warranted for one year from date of purchase
to be free of defects in materials and workmanship.
In event of such defect, product will be repaired without
charge or replaced (at our option) with a new product
of equal or superior value. This warranty excludes
defects due to normal wear, abuse, shipping damage,
or failure to use product in accordance with instructions.
This warranty is void in the event of unauthorized repair
or modication.
Please register your product warranty and always
KEEP YOUR RECEIPT.
REGISTER YOUR WARRANTY
Your prompt product registration establishes your right to
the protection available under the terms and conditions of
your Point Source Audio warranty. It also helps us contact
you in the rare event that we discover an issue with your
product. And, it helps us to bring you new products
specically designed to meet your needs.
www.point-sourceaudio.com/warranty.html
© 2017 Point Source Audio. All rights reserved. The Point Source
Audio logo is a registered trademark of Point Source Audio. All other
trademarks included herein are the property of their respective owners.
Patent No. D786,220 and 9,706,285
EO-8WR Specications
Omnidirectional Earmount Microphone
ELEMENT: (2) Back Electret Condenser
POLAR PATTERN: Omnidirectional
FREQUENCY RESPONSE: 20 Hz ~ 20 kHz
SENSITIVITY: -43dB ±3dB
(0db = 1V/microbar at
1kHz)
OUTPUT IMPEDANCE: 1400Ω (at 1kHz)
OPERATING VOLTAGE: 1 ~ 10 V
CABLE LENGTH: 6 ft. + connector
NET WEIGHT: 0.8 oz
MAXIMUM SPL: 136dB SPL
INCLUDED ACCESSORIES: 2 Earmounts, windscreen,
cable clip, 2 slider clips,
and storage box.
www.point-sourceaudio.comwww.point-sourceaudio.comwww.point-sourceaudio.com
Read the enclosed instructions and cautions thoroughly
before using this product. Failure to observe the proper
use of this product could result in voiding your warranty.

Customizing Your EMBRACE Microphone
Using With Your Wireless System
Your EO-8WR microphone comes equipped with two
hardwired connectors specied at the time of purchase.
There are two feet of separation between the connectors
and we recommend separating the body packs as far
apart as is comfortable to avoid cross talk interference.
Do NOT attempt to re-terminate the microphone
yourself. Making physical changes to the microphone
electronics or wiring will void your warranty.
To prolong the life of your cable, always remove the
microphone by grasping the connector - NEVER tug on
the cable to disconnect the microphone from the body-
pack.
Storing Your Microphone
When storing your microphone, use
care to coil the cable so that it rests at.
Store with windscreen on to prevent
possible damage to the element.
Do NOT wrap the cable around
the body pack or coil the cable
in any way that creates serious
bends or strain on the cable.
www.point-sourceaudio.comwww.point-sourceaudio.com www.point-sourceaudio.com
Read Before Use
Read the enclosed instructions and cautions thoroughly before
using this product. Failure to observe the proper use of this
product could result in voiding your warranty.
Note: The products pictured here are for illustration purposes
and may not look exactly like the product you have purchased.
What to Know About Your EMBRACE Earmounts
Front View Back View
Shapeable Area
Trimmable Areas
(a) Corner Elbow (c) Microphone Entrance (d) Cable Trench (e)
Cable Exit (f) Finishing Caps
b
d
c
a
ab
e
e
c
Do NOT pull the microphone element.
To reposition the microphone, REMOVE it completely from
the Earmount and re-trench the cable.
Bend along the shapeable areas to retain desired shape.
1. Use wire clippers to cut
at the corner elbow (a).
3. Attach the Finishing Cap
(e). Bend and shape the
Earmount as needed to sit
comfortably on the ear.
2. Start at the mic entrance
(b) and press the cable
(not the element) into
the trench (c). Continue
pressing cable until you
reach the exit (d).
Do NOT trim the
Earmount with the
microphone entrenched.
IMPORTANT!
Tuck the Finishing Cap into the
nook BEHIND the earlobe for a
secure t. Dress and secure mic
cable according to best practice.