Polanik STT60-S295 User manual

TECHNICAL SPECIFICATION
ASSEMBLY MANUAL
Pole vault training stands
STT60-S295
STT45-S293
File: 20117-11-28
PRODUCT SUPPORT
Paweł Ciechanowski
p.ciechano[email protected]m

Technical specification/Assembly manual STT60-S295 STT45-S293 2/14
Thank you for choosing Polanik Training pole vault stands.
Safe assembly and use
Before you start to assemble and use the stand please read this manual carefully.
Do not install or use the stands without a landing area.
The stand bases must be anchored to the ground.
During idle periods the posts of the stands which are installed outside must be unscrewed from the bases,
put on the landing area and the whole jumping facility (including the stand bases) must be secured with
garage.
The sports equipment produced by Polanik is designed for athletics training and use in sports competitions
only. Please pay special attention especially when using throwing implements and other throwing
equipment, misuse of athletics equipment and implements can cause serious injury or in extreme cases even
death. That is why training and use during sports events have to be always supervised by authorized sports
personnel. In no event shall Polanik be liable for any special, incidental, indirect or consequential damages in
connection with the purchase or use of POLANIK products or costs over the original cost of the product.
Unauthorized copying of this manual, in whole or in part, is prohibited.
The contents of this manual are subject to change without notice.
The producer reserves the right to introduce without warning changes in product constructions and colours.

Technical specification/Assembly manual STT60-S295 STT45-S293 3/14
I. General use and description
STT60-S295 and STT45-S293 are complete pole vault training stands sets. Both sets include the following
elements:
Part/set description
Q-ty
Pcs.
Part/set sketch
Base
(s-0293-021-01-00-00 right;
s-0293-022-01-00-00 left)
2
Crossbar support
(S-0293-021-07-00-00 right;
S-0293-022-07-00-00 left)
2
Post
(S-0293-021-05-01-00 right;
S-0293-022-05-01-00 left)
2

Technical specification/Assembly manual STT60-S295 STT45-S293 4/14
II. Technical specification
V. Packing and transport
The set is delivered in parts. Boxes’ dimensions:
1/3 6,65 x 0,35 x 0,35 [m]- post packed in foil
2/3 6,65 x 0,35 x 0,35 [m]- post packed in foil
3/3 1,70 x 0,85 x 0,65 [m]- bases and crossbar supports on a pallet
Gross weight - 160 kg.
STT60-S295
STT45-S293
Stand type
training
training
Crossbar
support
aluminium, powder painted
aluminium, powder painted
Post
special aluminium anodized
profile, detachable
special aluminium anodized
profile, detachable
Base
galvanized steel, powder
painted steel sheets, equipped
with wheels, with 4 anchoring
holes
galvanized steel, powder
painted steel sheets, equipped
with wheels, with 4 anchoring
holes
Crossbar
support
lifting
mechanism
hand crank with brake, smooth
operation
hand crank with brake, smooth
operation
Post shifting
mechanism
manual with hand wheel
brake, smooth operation
system based on special guide
rolls
manual with hand wheel
brake, smooth operation
system based on special guide
rolls
Height range
[cm]
160 –600
160 –450
Post
horizontal
shift range
[cm]
0-80
0-80
Set net
weight [kg]
148
140

Technical specification/Assembly manual STT60-S295 STT45-S293 5/14
STT45-S293 [mm] STT60-S295

Technical specification/Assembly manual STT60-S295 STT45-S293 6/14
III. Assembly
Step
Description
Image
1
Unpack the product:
remove a foil from a
pallet and using two
19 wrenches unscrew
nuts on each pallet’s
corner, remove a foil
from posts.
2
Read all marks
carefully.

Technical specification/Assembly manual STT60-S295 STT45-S293 7/14
Step
Description
Image
3
Ease the screws using
a metric wrench no.
13.
4
Put in the post.
5
Tighten the screws
using a wrench no.
13.
6
Fasten the crossbar
support using a hex
key no. 6.

Technical specification/Assembly manual STT60-S295 STT45-S293 8/14
Step
Description
Image
7
Change the crank
lever’s position from
“transport position”
to “work position”:
unscrew a fastening
nut, rearrange the
crank lever, home the
nut using a metric
wrench no. 17.
8
Transport assembled
stands to the place of
exploitation.

Technical specification/Assembly manual STT60-S295 STT45-S293 9/14
Step
Description
Image
9
After assembly and
positioning the stands
their bases must be
fastened to the
ground using the
mounting holes of the
flat bars of the bases.
The omission of that
operation may cause
the stands overturn
and result in serious
accident or damages.
It is recommended that hex nut head steel sleeve anchors dia. 12 mm and
length 100 mm (holes in concrete must be of dia. 12 mm and 100 –120 mm
deep) are used for anchorage. The concrete layer is to be dry and non-cracked.
For the installation of the anchors please see their producer’s instruction.
Recommended concrete foundations are shown below:
[mm]
The stand bases situated in the foundations:
[mm]

Technical specification/Assembly manual STT60-S295 STT45-S293 10/14
IV. Operating and maintenance
To block/unlock the crank lever change its position by following the marks on the crank.
To avoid bases’ shifts during exploitation, block them using the base brake, turn the knob clockwise to block
the post shift and turn it counterclockwise to release the brake.
As the producer we have done our best to make pole vault stands guarantee maximum safety level, be easily
operated and reliable in use. However the stands like any other pieces of sports equipment requires periodical
inspections and must be used according to the instruction manual and operated by authorized personnel.
While operating the stands the following rules must be observed:
The base wheels should be only used to transport the stands on level surfaces and within short
distances. For long distances you must unscrew the posts from the bases.
While changing the height of the crossbar support or adjusting the distance of the post to “0” line make
sure to slow down before reaching extreme positions. That allows you to avoid “banging” which may
result in excessive load of the mechanisms.
During idle periods the posts of the stands, which are installed outside, must be unscrewed from the
bases, put on the landing area and the whole jumping facility (including the stand bases) must be
secured with garage.
If there is no garage available in the facility, only during summer athletics season the unscrewed posts
can be put on the landing area on the condition that the posts and the bases are protected against rain
with waterproof covers (not included).
When the summer athletics season ends the stands (including the bases) must be dismounted and
stored in a dry and roofed place.

Technical specification/Assembly manual STT60-S295 STT45-S293 11/14
VI. Declarations
1) Declaration No. 2014-07-17
2) Issuer’s name: POLANIK
Issuer’s address: Życzliwa 11, 97-300 Piotrkow Tryb.
3) Items of declaration
4) The object of declaration described above is in conformity with the requirements of the following documents:
Document no.
Title
Edition/Date of issue
Rule 183
point 9, 10
Competition Rules 2014-2015
International Association of Athletics
Federations
IAAF
17, rue Princesse Florestine
BP 359 –MC 98007 Monaco Cedex
Tel. [phone]
Faks [phone]
www.iaaf.org
Additional Information
5)Declaration for:
BUYER and USER
Signed for and in behalf of:
POLANIK
2014-07-17 Piotrkow Tryb.
(Date and place of issue)
Pawel Ciechanowski
Product Manager
6)……………………………………… ……………………………………………………………………………
(Name, function) (Signature or equivalent authorized by the issuer)
No.
Name
Code
1
Training pole vault stand
STT60-S295

Technical specification/Assembly manual STT60-S295 STT45-S293 12/14
1) Declaration No. 2014-07-17
2)Issuer’s name: POLANIK
Issuer’s address: Życzliwa 11, 97-300 Piotrkow Tryb.
3)Items of declaration
4)The object of declaration described above is in conformity with the requirements of the following documents:
Document no.
Title
Edition/Date of issue
Rule 183
point 9, 10
Competition Rules 2014-2015
International Association of Athletics
Federations
IAAF
17, rue Princesse Florestine
BP 359 –MC 98007 Monaco Cedex
Tel. [phone]
Faks [phone]
www.iaaf.org
Additional Information
5)Declaration for:
BUYER and USER
Signed for and in behalf of:
POLANIK
2014-07-17 Piotrkow Tryb.
(Date and place of issue)
Pawel Ciechanowski
Product Manager
6)……………………………………… ……………………………………………………………………………
(Name, function) (Signature or equivalent authorized by the issuer)
No.
Name
Code
1
Training pole vault stand
STT45-S293

Technical specification/Assembly manual STT60-S295 STT45-S293 13/14
VII. Images
STT45-S293 © 2017 Polanik

Technical specification/Assembly manual STT60-S295 STT45-S293 14/14
STT60-S295 © 2017 Polanik