X-Stand FALCON XSFP419 Quick guide

This X-Stand™ product(s) has been tested to rigid industry standards. Safe operation and use
of this X-Stand™ product(s) is the responsibility of the user(s). Please read and follow all safe
use instructions and warnings. Failure to follow these may result in serious injury or death!
Second Edition, April 2020, Published by X-Stand™ TREESTANDS,
Lakeville Minnesota. © 2019 X-Stand™ TREESTANDS. All right reserved.
FALCON

READTHIS MANUAL IN ITS ENTIRETY PRIOR TO USINGTHIS PRODUCT.
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
2
ATTENTION!! WHEN YOUSEE A “ WARNING!” BE SURE TO HEED THEMESSAGE!
THE INFORMATION CONTAINED IN THESE MESSAGES CAN SAVE YOUR LIFE!!
Max. Weight Capacity (User(s) and Equipment) 300 lbs (136 kg)
XSFP419 - FALCON
HANG-ON AND CLIMBING SYSTEM SAFE USAGE INSTRUCTIONS & WARNINGS
WARNING!
This product carries strict weight restrictions. Please note that these weight
limitations include the user(s) and their equipment. DO NOT use these product(s) if you
exceed these total weight limitations. Failure to follow these instructions may result in
serious injury or death!
A safe treestand hunting video, TreestandSafety: It’s Up To You, has been included.
Please view it in its entirety prior to using this product! Thank you for your purchase of
this quality X-Stand™ Treestands product. To ensure your personal safety, please take a
moment to carefully read this Instruction Manual in its entirety before attempting to
assemble, set-up, install and/or otherwise use this X-Stand™ Treestands product. Failure
to follow these instructions may result in serious injury or death!
Should you have any questions about the installation and/or use of this product, or any
other X-Stand™ Treestands product(s) do not hesitate to call one of our customer service
representatives at 540-877-2769 or email at [e-mail] . Our customer service
representatives will answer any questions you may have about any of the complete line of
X-Stand™ Treestands products.
Do not return this product to the retailer if you have any damaged or missing parts. Call
X-Stand™ Treestands for replacement of any damaged or missing parts at 540-877-2769
or email at [email protected] .
WARNING!
Failure to read and strictly comply with the instructions contained in this
Instruction Manual may result in serious injury or death!
WARNING!
FALLS FROM A TREESTAND CAN OCCUR ANYTIME AFTER LEAVING THE
GROUND. THESE FALLS COULD RESULT IN EITHER SERIOUS INJURY OR DEATH! FOR YOUR
PERSONAL SAFETY, PLEASE TAKE A MOMENT TO CAREFULLY READ THIS PRODUCT
INSTRUCTION MANUAL IN ITS ENTIRETY BEFORE ATTEMPTING TO ASSEMBLE, SET-UP,
INSTALL AND/OR OTHERWISE USE THIS X-STAND ™ PRODUCT. AT LEAST
ANNUALLY, REVIEW THE CONTENTS OF THIS INSTRUCTION MANUAL AND WATCH THE
SAFE TREESTAND HUNTING DVD. ADDITIONALLY, KEEP THESE INSTRUCTIONS FOR THE
ENTIRE DURATION THAT YOU OWN THIS PRODUCT(S). FAILURE TO FOLLOW THESE
INSTRUCTIONS MAY MAY RESULT IN SERIOUS INJURY OR DEATH!
WARNING! A
Treestand Safety: It’s Up To You DVD has been included with this
tree-
stand. Pleaseview it in its entirety prior to using this or any other X-Stand™
product(s). Failure to follow these instructions may result in serious injury or death!
WARNING!
THE SAFE USE AND OPERATION OF THIS PRODUCT IS THE SOLE RESPONSI-
BILITY OF THE USER. IT IS ALSO THE SOLE RESPONSIBILITY OF THE OWNER TO PROVIDE
ANY PERSON(S) WHO BORROW OR PURCHASE THIS PRODUCT WITH THESE INSTRUCTIONS
AND THE AFORE MENTIONED TREESTAND SAFETY: IT’S UP TO YOU DVD.
FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR DEATH!
ADDITIONALLY, FAILURE TO FOLLOW THIS INSTRUCTION MAY SUBJECT YOU TO PERSONAL
LIABILITY PENALTIES AS DETERMINED BY THE U.S. JUDICIAL SYSTEM.
WARNING!
Prior to each hunt, you must inform someone of your hunting location,
including the specific location of your treestand and the expected duration of your hunt. Failure
to follow these instructions may result in serious injury or death!
WARNING!
Prior to each hunt, make sure that you have a signaling device (e.g., mobile
phone, radio, whistle, signal flare or Personal Locator Device (PLD)) in your possession and
in an operable condition. This device must be within easy access should you experience
the need to contact emergency assistance. Failure to follow these instructions may result
in serious injury or death!
WARNING! DO NOT
remove, modify,and/or omit any portion or otherwise mechanically
modify this X-Stand™ product(s) or its assemblies in any manner. Modification, misuse, and/
or part substitution shall immediately void your factory warranty and may result in serious
injury or death! If you suspect that a part(s) is missing and/or defective, immediately
contact X-Stand™ at 540-877-2769 or email at [email protected]
for replacement of
missing or defective parts. Never
modify your stand in any way by making repairs, or
altering, adding or attaching anything to it except if explicitly authorized in writing by
X-Stand™. ALWAYS USE GENUINE FACTORY AUTHORIZED X-STAND™
REPLACEMENT PARTS. USE OF ANY REPLACE- MENT PARTS OTHER THAN
GENUINE X-STAND™ PARTS VOIDS YOUR WARRANTY AND MAY RESULT IN
SERIOUS INJURY OR DEATH!
WARNING!
ALWAYS inspect/check ALL expiration dates/tags on all straps and the
full-body fall arrest harness and its components prior to each use. You must replace ALL
straps and suspension seats EVERY year. Never use any strap(s) or full-body fall arrest
harness or its components that has expired and/or is showing any signs of damage and/
or wear. Failure to follow these instructions may result in serious injury or death!
WARNING!
Make certain all chains, cables, straps, etc. are tightened per this Instruction
Manual prior to use. All treestand contact points must be in contact with the tree before
you step onto the stand. The correct adjustment and tightening of attachment hardware is
critical to the stable installation of this treestand. Additionally, you MUST be wearing your
Fall Arrest System (FAS) which includes a full-body fall arrest harness, tree belt, lanyard/
tether, suspension relief device and climbing belt/lineman’s belt (as applicable) in accor-
dance with the Instructions contained in this Instruction Manual. Failure to follow these
instructions may result in serious injury or death!
WARNING!
This product(s) is designed for adult use only. No one under the age of
16 should attempt to use this or any other X-Stand™ product(s) without direct adult
supervision. Failure to follow these instructions may result in serious injury or death!
WARNING!
Prior to attempting to use this or any other X-Stand™ product(s) you must
take a moment and become familiar with its assembly, setup and installation. You must
practice installing, setting-up and using your full-body fall arrest harness and its compo-
nents (i.e., lanyard/tether, tree belt, suspension relief device, climbing belt/lineman’s belt
[as applicable]) at ground-level prior to attempting to use it at heights above ground-level.
Once you have become thoroughly knowledgeable and comfortable with this X-Stand™
X-Stand™ product(s) setup, installation and use at ground-level, you are now ready to use
it at heights above ground-level. Failure to follow these instructions may result in serious
injury or death!
WARNING!
Several X-Stand™ Treestands are equipped with a footrest, armrests and/
or shooting rail. Neither the footrest, armrests nor the shooting rail have been designed to
support the users weight. Under no circumstances should you place any more than fifteen
(15) lbs (6 kg) of weight on these structures. Doing so will put the user in serious risk of
injury or death. Failure to follow these instructions may result in serious injury or death!
WARNING!
You must wear a Fall Arrest System (FAS) comprising of a full-body fall
arrest harness, tree belt, lanyard/ tether , suspension relief device and climbing belt/
lineman’s belt (as applicable) at all times after leaving the ground. You must stay
connected at all times after leaving the ground while using fixed position treestands.
Single safety belts and chest harnesses are no longer allowed and should never be
used. If you are not wearing a full-body fall arrest harness that is properly attached to
the tree to protect you from a fall, do not leave the ground nor attempt to enter your
treestand. Failure to follow these instructions may result in serious injury or death!
WARNING!
Never attempt to climb up or down with a weapon and/or gear in your
possession. ALWAYS unload your weapon and pull it up to hunting height using a tether
or pull up rope. ALWAYS lower your unloaded weapon down to the ground prior (when
raising or lowing firearms, the chamber must be open and barrel pointing toward the
ground) to attempting to climb up or climb down. Use this same method when raising
or lowering all other gear. Failure to follow these instructions may result in serious injury
or death!

READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USINGTHIS PRODUCT.
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.

ATTENTION!! WHEN YOUSEE A “ WARNING!” BE SURE TO HEED THEMESSAGE!
THE INFORMATION CONTAINED IN THESE MESSAGES CAN SAVE YOUR LIFE!!
3
WARNING!
Prior to each use thoroughly inspect the treestand and all of its related
components and all safety devices before use for signs of wear, rot, corrosion, cracks,
deterioration and/or any other type of defect. Make certain that your treestand is tight
and secure prior to use. Protect this product from extended exposure to direct sunlight,
excessive heat or freezing temperatures by storing inside when not in use. DO NOT
use this or any other product(s) if it shows evidence of wear, rot, corrosion, cracks,
deterioration and/or any other type of defect. Failure to follow these instructions may
result in serious injury or death!
WARNING! DO NOT
use this or any other X-Stand™ product(s) if you have a history
of heart problems, back problems, impaired vision, joints that lock-up, spinal fusions,
equilibrium problems, high blood pressure, are not well-rested and/or any other physical
impairment that may limit your ability to use and/or operate this product(s) in the safe
manner outlined in this Instruction Manual. Additionally, do not use this or any other X-
Stand™ product(s) if you are currently taking medication (including prescription) and/or
using and/or consuming any substance, including alcohol, that may limit your ability to
use this X-Stand™ product(s) as outlined and described in the Instruction Manual. Never
use a treestand when feeling ill, nauseous or dizzy. Failure to follow these instructions
may result in serious injury or death!
WARNING!
DO NOT attempt to make adjustments to this product while in the treestand
All adjustments must be made with the entire treestand on the ground. Failure to follow
these instructions may result in serious injury or death!
WARNING!
DO NOT leave your X-Stand™ product(s) installed for more than two
weeks (14 days). Any number of factors can jeopardize its installation and integrity. These
include, but are not limited to, weather or other environmental factors that can negatively
affect its performance. Animals can also cause damage to your X-Stand™ product(s)
that can negatively affect its performance and your safety. Additionally, factors such as
tree growth can stress and damage supporting straps, cables, chains and/or buckles.
Failure to follow these instructions may result in serious injury or death!
WARNING!
ALWAYS inspect the treestand and all safety devices prior to each use. DO
NOT use this product(s) if it shows signs of wear, damage, deterioration, or vandalism.
Factors such as tree growth, vandals, weather and animals may affect the performance of
an unattended treestand. Failure to follow these instructions may result in serious injury
or death!
WARNING!
DO NOT modify, fix/repair, alter, bend, cut, weld, drill or heat the treestand
in any way. Also, do not attach anything to your treestand without explicit authorized and
written instructions from the manufacturer. Failure to follow these instructions shall void
warranty and may result in serious injury or death!
WARNING!
Strict weight limitations have been set for each product to ensure your
personal safety. Note the weight limitations of your stand and that this weight limit
includes the user (one person) and their equipment. NEVER EXCEED THESE WEIGHT
LIMITATIONS! Failure to follow these instructions may result in serious injury or death!
WARNING! DO NOT
attempt to use this or any other X-Stand™ product(s) when ice,
snow, and/or freezing rain has deposited or formed on any portion of the tree or stand
you intend to climb. Do not attempt to use this or any other X-Stand™ product(s) when
use this or any other X-Stand™ product(s) when any other adverse weather condition
thunderstorms are threatening and/or present within five (5) miles. Do not attempt to
presents itself. These include, but are not limited to, weather conditions which have the
potential for producing winds, lightning, rain, snow, sleet and/or any other atmospheric
condition which may limit the user’s ability to operate this X-Stand™ product(s) in a safe
manner as described in this Instruction Manual. Should inclement weather conditions
arise during your use of this X-Stand™ product(s), return to the ground immediately.
Failure to follow these instructions may result in serious injury or death!
WARNING!
DO NOT jump or bounce on the treestand platform and/or the seat to
engage the stand to the tree. Failure to follow these instructions may result in serious
injury or death!
WARNING!
BEFORE each use, make sure all nuts and bolts are secure. CHECK all
hardware and webbing prior to every use to make sure that no damage has occurred
to hardware and that webbing (as applicable) is not cut or frayed. Keep webbing from
coming into contact with any sharp edges. DO NOT USE THIS PRODUCT IF ANY DAMAGE
IS SUSPECTED. Failure to follow these instructions may result in serious injury or death!
WARNING!
REPLACE any damaged or worn part with original parts. Replace attach-
ment straps every one year and when not in use store in a dry, cool, safe place away from
sunlight. Never store a treestand or any of its components outdoors when not in use. To
purchase parts contact X-Stand™ Treestands at 540-877-2769 or email at cs@x-
stand.com . Failure to follow these follow these instructions may result in serious injury or
death!
WARNING!
Always wear the appropriate foot wear when using a treestand. A good
non-slip safety boot is important for your safety. Be especially careful that boot laces
do not get hooked on the tree stand or its components (tuck shoelaces into boot before
climbing). Failure to follow these instructions may result in serious injury or death!
WARNING!
DO NOT use this product, or attempt to use a treestand, on a dead, leaning
diseased, loose barked tree (bark that flakes or falls off), irregular shaped trees,or utility
poles. DO NOT use this product on any tree that does not allow for a level standing plat-
form. Failure to follow these instructions may result in serious injury or death!
WARNING!
NEVER hunt out of a treestand at heights at which you are not completely
comfortable. Depending upon the tree and hunting conditions, choose the minimum
hunting height that allows for safe, effective hunting. Failure to follow these instructions
may result in serious injury or death!
WARNING!
DO NOT
use this, or any other X-Stand™ product(s) to climb utility poles,
telephone poles, structural columns or any other man-made structures. Never use this or
any other X-Stand™ product(s) around power generation (e.g., transformers, generators,
substations, etc.) and/or power transmission equipment. Never use a treestand on a dead,
leaning, diseased or loose barked tree. NEVER USE A TREE BRANCH, OR ANY PORTION
OF A TREE, TO SUPPORT ANY PORTION OF YOUR WEIGHT OR AS A HAND HOLD. Failure
to follow these instructions may result in serious injury or death!
WARNING! DO NOT
stand on the treestand seat. Failure to follow these instructions
may result in serious injury or death!
WARNING!
This X-Stand™ Treestand product(s) was designed for installation on trees
with a minimum diameter of nine (9) inches (23 cm) to maximum diameter of twenty (20)
inches (51 cm) at treestand installation height (i.e., seat height). DO NOT use your X-Stand™
product(s) on trees with trunk diameters that do not meet these diameter requirements.
Failure to follow these instructions may result in serious injury or death!
WARNING!
Always maintain three-point contact when climbing up or down a tree.
Proper three-point contact means having either two feet with one hand or one foot with
two hands on the step portion of the ladder at all times when climbing up or down. Failure
to follow these instructions may result in serious injury or death!
WARNING!
Never attempt to hunt from an unlevel standing and/or seating platform.
Additionally, NEVER attempt to level your standing and/or seating platform at heights
above the ground. Failure to follow these instructions may result in serious injury or death!
WARNING!
DO NOT jump or bounce on the treestand platform (or any of the treestands
components) and/or the seat to engage the stand to the tree. Failure to follow these instruc-
tions may result in serious injury or death!
WARNING!
Climbing aids (e.g., stick ladders, sectional ladders, etc.) must be installed
and extend a minimum of 24-inches (2 feet) above the seating platform. This practice
allow the user to have a firm hand hold when stepping down onto the foot platform. NEVER
attempt to step up onto your foot platform. Failure to follow these instructions may result
in serious injury or death!
WARNING! NEVER ATTEMPT to step onto a treestand until all treestand contact points
are secured tightly and firmly to the tree. NEVER ATTEMPT to step onto a treestand unless
your full-body fall arrest harness is properly attached. Failure to follow these instructions
may result in serious injury or death!
WARNING!
When installing your hang on treestand, you must wear your full-body fall
arrest harness and use the climbing belt at all times while installing or removing your
fixed position treestand. The use of the climbing belt ensures your stable attachment to
the tree until installation is complete. Failure to follow these instructions may result in
serious injury or death!

READTHIS MANUAL IN ITS ENTIRETY PRIOR TO USINGTHIS PRODUCT.
This instruction manual complies with ASTM F2337 Standard Test Method for Treestand Fall Arrest Systems.

ATTENTION!! WHEN YOUSEE A “ WARNING!” BE SURE TO HEED THEMESSAGE!
THE INFORMATION CONTAINED IN THESE MESSAGES CAN SAVE YOUR LIFE!!
4
FULL-BODY FALL ARREST HARNESS USAGE INSTRUCTIONS & WARNINGS
WARNING!
When installing your treestand, never attempt to climb with your treestand
in your possession. Always use a pull up rope to raise and lower the treestand during
installation and removal. NEVER ATTEMPT TO CLIMB WITH ANY HUNTING COMPONENT
OR ACCESSORY IN HAND OR ON YOUR BACK. Failure to follow these instructions may
result in serious injury or death!
WARNING!
ground-level and readjust your treestand as necessary to alleviate this awkward angle.
ward or downward, or in any configuration other than level, immediately climb down to
If you find that your treestand is unlevel, canted, angled awkwardly up-
Never attempt to hunt from an unlevel treestand. Additionally, never attempt to level your
treestand at heights above the ground. Failure to follow these instructions may result in
serious injury or death!
WARNING!
Never install, set-up, or climb to your treestand with a weapon. Use a
pull-up rope to carefully raise your unloaded weapon after full-body fall arrest harness is
secure and you are set in the stand!
WARNING!
An ASTM compliant full-body fall arrest harness with a lineman’s/climbing
belt must be worn at all times while installing or removing any hangon style treestands
or climbing aids (i.e., ladders, sticks, steps, etc.). Failure to follow these instructions may
result in serious injury or death!
WARNING!
DO not over tighten the hardware. Over tightening can lead to structural
damage and may negatively affect the performance of your stand. Failure to follow these
instructions may result in serious injury or death!
WARNING!
Failure to read and strictly comply with the instructions contained here
may result in serious injury or death!
WARNING! READ ALL THE INFORMATION INCLUDED HERE PRIOR TO ATTEMPTING TO
USE THIS FULL-BODY FALL ARREST HARNESS AND ITS COMPONENTS. YOUR FULL-BODY
FALL ARREST HARNESS AND ITS COMPONENTS ARE DESIGNED FOR A MAXIMUM WEIGHT
CAP ACITY (USER AND EQUIPMENT) OF 300 POUNDS (136 KG). ADDITIONALLY, YOUR
FULL BODY FALL ARREST HARNESS AND ITS COMPONENTS MUST BE REPLACED AFTER
FIVE (5) YEARS OF SERVICE! PLEASE CONTACT X-STAND™ TREEST ANDS FOR FULL-BODY
FALL ARREST HARNESS REPLACEMENT PROCEDURE SHOULD YOU EXPERIENCE A FALL
OR SHOULD IT EXCEED THE FIVE (5) YEARS SERVICE PERIOD.
WARNING!
Prior to attempting to use this or or any other X-Stand™ product(s) you
must take a moment and become familiar with its assembly, setup and installation. You
must practice installing, setting-up and using your full-body fall arrest harness at ground-
level prior to attempting to use it at heights above ground-level. Once you have become
thoroughly knowledgeable and comfortable with this product(s) setup, installation and
use at ground-level, you are now ready to use it at heights above ground-level. Failure to
follow these instructions may result in serious injury or death!
WARNING!
You must wear a Fall Arrest System (FAS) comprising of a full-body fall
arrest harness, tree belt, lanyard/ tether , suspension relief device and climbing belt/
lineman’s belt (as applicable) at all times after leaving the ground. You must stay
connected at all times after leaving the ground while using fixed position treestands.
Single safety belts and chest harnesses are no longer preferred and should never be
used. If you are not wearing a full-body fall arrest harness, do not leave the ground.
Failure to follow these instructions may result in serious injury or death!
WARNING!
ALWAYS practice using your full-body fall arrest harness (FAS) in the
presence of a responsible adult prior to using it in an elevated hunting environment,
and learn what it feels like to hang suspended in the harness at ground level. Practice
installing and using your treestand at ground level and with a responsible adult present
before you go hunting.
WARNING!
The length of the full-body fall arrest harness tether must be kept to a
minimum at all times during use. It should be adjusted so that it is above the head with
no slack (snug) in the sitting position. Never allow the full-body fall arrest tether to get
under your chin, around your neck, or under your arm(s). Failure to follow these instructions
may result in serious injury or death!
WARNING!
Should you experience a fall there is time to make a correct decision on
what action needs to take place. It is important to remember: DO NOT PANIC! Failure to
follow this warning may result in serious injury or death!
WARNING!
If you have a limiting physical and/or health condition that precludes and/
or renders you incapable of self-recovery and/or a suitable escape plan is not available,
DO NOT hunt from heights above ground-level. Failure to follow these instructions may
result in serious injury or death!
WARNING!
FALLS FROM A TREESTAND CAN OCCUR ANYTIME AFTER LEAVING THE
GROUND. THESE FALLS COULD RESULT IN EITHER SERIOUS INJURY OR DEATH! FOR
YOUR PERSONAL SAFETY, PLEASE TAKE A MOMENT TO CAREFULLY READ THIS PRODUCT
INSTRUCTION MANUAL IN ITS ENTIRETY BEFORE ATTEMPTING TO ASSEMBLE, SET-UP,
INSTALL AND/OR OTHERWISE USE THIS X-STAND™ PRODUCT. AT LEAST ANNUALLY,
REVIEW THE CONTENTS OF THIS INSTRUCTION MANUAL AND WATCH THE SAFE TREE-
STAND HUNTING DVD. ADDITIONALLY, KEEP THESE INSTRUCTIONS FOR THE ENTIRE
DURATION THAT YOU OWN THIS PRODUCT(S). FAILURE TO FOLLOW THESE INSTRUCTIONS
MAY RESULT IN SERIOUS INJURY OR DEATH!
WARNING!
THE SAFE USE AND OPERATION OF THIS PRODUCT IS THE SOLE RESPON-
SIBILITY OF THE USER. IT IS ALSO THE SOLE RESPONSIBILITY OF THE OWNER TO PROVIDE
ANY PERSON(S) WHO BORROW OR PURCHASE THIS PRODUCT FROM THEM WITH THESE
COMPLETE INSTRUCTIONS. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN
SERIOUS INJURY OR DEATH! ADDITIONALLY, FAILURE TO FOLLOW THESE INSTRUCTIONS
MAY SUBJECT YOU TO PERSONAL LIABILITY PENALTIES AS DETERMINED BY THE U.S.
JUDICIAL SYSTEM.

READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USINGTHIS PRODUCT.
This instruction manual complies with ASTM F2337 Standard Test Method for Treestand Fall Arrest Systems.
5
ATTENTION!! WHEN YOUSEE A " WARNING!" BE SURE TO HEED THEMESSAGE!
THE INFORMATION CONTAINED IN THESE MESSAGES CAN SAVE YOUR LIFE!!
FULL-BODY FALL ARREST HARNESS INSTRUCTIONS
WARNING! READ THESE X-STAND™ TREESTANDS FULL-BODY FALL ARREST HARNESS INSTRUCTIONS CAREFULLY AND FOLLOW ALL THE INSTRUCTIONS!
YOUR NEW FULL-BODY
FALL ARREST HARNESS IS DESIGNED FOR A MAXIMUM CAPACITY (USER & EqUIPMENT) OF 300 POUNDS (136 KG). ADDITIONALLY,
YOUR NEW FULL-BODY FALL ARREST HARNESS
MUST BE REPLACED AFTER FIVE (5) YEARS OF SERVICE! REPLACE YOUR HARNESS IMMEDIATELY SHOULD YOU EXPERIENCE A FALL WHILE WEARING IT.
WARNING! You must use the X-Stand™ Treestand full-body fall arrest harness provided with this product or a harness that complies with ASTM standards. NOTE: You must store
your full-body fall arrest harness out of direct sunlight and out of any other harsh environmental condition(s) that may adversely affect its performance. Failure to follow these
instructions may result in serious injury or death!
STEP 1.
Identify the main parts of the full-body fall arrest harness (see Fig. 1). Hold the
full-body fall arrest harness by the tether loop ensuring the harness is upright and leg
straps are hanging down. Straighten any parts that have become twisted. Insert arms
through each shoulder strap. (see Fig. 2)
STEP 2 .
Feed the left leg strap between legs and thread through the bottom left waist
loop. Repeat with the right leg strap, feeding between legs and through right waist loop.
(see Fig. 3)
STEP 3 .
Secure the two leg straps by threading the 3 bar buckle as shown in Figure 4.
Tighten the leg straps snuggly. DO NOT over tighten as this will cut off the circulation to
your legs. The X-Stand™ Treestands full-body fall arrest harness should look like the
one depicted in Figure 6 when done correctly. Note : If leg straps are too long, feed right
leg strap with buckle through bottom of the right waist loop, down the top of the right
waist loop and secure to right leg strap with 3 Bar Buckle as instructed.
WARNING!
It is very important to complete this Step of the assembly. Improperly
secured buckle may cause full-body fall arrest harness failure resulting in serious
injury or death! If there is not enough strap available to complete this step, DO NOT
USE THIS FULL-BODY FALL ARREST HARNESS! You may need to purchase and use a
larger specialty sized full-body fall arrest harness that complies with ASTM standards.
STEP 4 .
through one of the waist loops and wrap the free end around the tree. Then feed opposite
If necessary to use a climbing belt for the field installation of your treestand (as
end through the opposite waist loop and use 3 bar buckle method described in FIG 4 to
secure see FIG. 5
STEP 5.
Once you have reached your desired height, insert the tree belt through the loop
of the tether. (see Fig. 6) Then, carefully wrap the tree belt around the tree at a height
that allows just enough slack for you to sit comfortably in your stand. Keeping the tether
as short as possible limits the distance you will travel in the unlikely event you should
experience a fall. To secure the tree belt insert free end up through the slot in the buckle
closest to opposite end of the tree belt, then cross over the sliding mechanism and back
down through opposites lot. Pull on strap to secure and test to make sure sliding mecha-
nism engages creating secure strap placement. (see Fig. 7, 8, 9)
WARNING!
Practice the use of your X-Stand™ Treestand full-body fall arrest harness
and suspension relief device (SRD) at ground-level in the presence of a responsible adult
to experience the feeling of hanging suspended before using in a hunting environment.
Failure to follow these instructions may result in serious injury or death!
WARNING!
NEVER allow the full-body fall arrest harness lanyard/tether to get under
your chin or around your neck. This poses a choking hazard that can lead to serious injury
or death. Failure to follow these instructions may result in serious injury or death!
WARNING!
If your hunting location is unknown by anyone and communication efforts
are unsuccessful, you must have a personal plan for self-recovery/escape should you
experience a fall. Prolonged suspension in a full-body fall arrest harness can be fatal. It is
important to exercise the legs by pushing against the tree or doing other forms of contin-
uous leg exercises to avoid blood pooling while being suspended. Varying degrees of
physical fifness may require different plans for self-recovery/escape the effects of
prolonged suspension. Have a personal plan and practice it in the presence of a respon-
sible adult before leaving the ground. No one escape/ rescue plan will work for every
hunter, on every tree, in every circumstance. Only you can determine the best self-
recovery/ escape plan for your hunting situation before leaving the ground. There is time
to make a correct decision on what action to take if a fall occurs while wearing a full-
body fall arrest harness. It is important to remember, DO NOT PANIC. Remain calm and
implement your practiced rescue, relief and recovery plan. Hunt from the ground when
a self-recovery/escape ability is absent. Failure to follow these instructions may result
in serious injury or death!
WARNING!
TO REDUCE YOUR RISK OF INJURY OR DEATH FROM FALLS YOU MUST
WEAR A LINEMAN STYLE (CLIMBING BELT) FULL-BODY FALL ARREST HARNESS THAT
MEETS ASTM STANDARDS. ALWAYS REMAIN HARNESSED TO THE TREE FROM THE
MOMENT YOU LEAVE THE GROUND UNTIL YOU RETURN TO THE GROUND. The lineman’s
(climbing belt) style full-body fall arrest harness must be worn in compliance with the
manufacturer’s instructions. If you do not or cannot use a lineman’s style (climbing belt)
full-body fall arrest harness that properly fits you must, under no condition, attempt to
use this or any X-Stand Treestand product(s).
WARNING!
When using a lineman’s belt/climbing belt to ascend the tree, the full-body
fall arrest harness tree belt and lanyard/ tether must be attached to the tree trunk before
stepping down on the treestand. Failure to follow these instructions may result in serious
injury or death!
per the specific Instructions for your specific treestand model), feed the climbing belt

READTHIS MANUAL IN ITS ENTIRETY PRIOR TO USINGTHIS PRODUCT.
This instruction manual complies with ASTM F2337 Standard Test Method for Treestand Fall Arrest Systems.
6
ATTENTION!! WHEN YOUSEE A “ WARNING!” BE SURE TO HEED THEMESSAGE!
THE INFORMATION CONTAINED IN THESE MESSAGES CAN SAVE YOUR LIFE!!
Tether
Tether
Loop
Tether
Loop
Three
Bar
Buckle
Three
Bar
Buckle
Front ViewRear View
SRD Strap
Right
Waist
Loop
Right
Leg Strap Right
Leg Strap
Left
Leg Strap
Left
Leg Strap
Left
Waist
Loop
Tether
SRD Strap
FIG 1
shoulder
strap shoulder strap
shoulder
strap shoulder strap
Leg Strap
waist
belt
Leg Strap
FIG 2
Slot A
Left
Leg
Strap
Right
Leg
Strap
Three Bar
Buckle
Up through Slot B
Down through Slot A
Down through Slot B
Pull tight to secure
Back over top
Slot B
FIG 4
tree
belt
Tree Belt
Side View
FIG 7
FIG 8
Climbing Belt
tree belt
tether
FIG 5
FIG 6
tree
belt
Standing
tether
Sitting/
Seating
tree
belt
tether
FIG 9
shoulder
strap shoulder strap
shoulder
strap shoulder strap
Leg Strap
waist
belt
Leg Strap
FIG 3

READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USINGTHIS PRODUCT.
This instruction manual complies with ASTM F2337 Standard Test Method for Treestand Fall Arrest Systems.

ATTENTION!! WHEN YOUSEE A " WARNING!" BE SURE TO HEED THEMESSAGE!
THE INFORMATION CONTAINED IN THESE MESSAGES CAN SAVE YOUR LIFE!!
To activate your product’s warranty, a registration card (found in the back of this manual)
must be completed and returned to the manufacturer within 30 days of purchase.
Be sure to keep a copy of this card for your records.
Should you have any questions about the assembly, installation or use of this X-Stand product,
or any other X-Stand products, please do not hesitate to call one of our customer service
representatives at 540-877-2769 or email at [email protected] and they will answer all
questions you may have about any of the complete line of X-Stand products.
STEPS TO FOLLOW IF A FALL WERE TO OCCUR:
Although no one plans to fall from their treestand, falls can and do occur without warning.
It is important to become familiar with the guidelines below and practice your recovery
plan at ground-level. Failure to read, understand, and follow these Steps may result in
WARNING! There is time to make a correct decision on what action to take if a fall
occurs while wearing a full-body fall arrest harness. It is important NOT TO PANIC!
Remain calm and implement your practiced rescue, relief and recovery plan. Failure to
follow these instructions may result in serious injury or death!
WARNING! A suspension relief device must be on your person and readily accessible
while using a full-body fall arrest harness. This device will allow you to relieve the
load on the lower extremities if suspended in a full-body fall arrest harness and help
maintain circulation in the legs and mitigate suspension trauma (blood pooling). Follow
all instructions below regarding the provided SRD (Suspension Relief Device) and NEVER
remove it from your full-body fall arrest harness. Failure to follow this warning may result
in serious injury or death!
STEP 1.
After a fall, take a moment to catch your breath and stay calm; DO NOT PANIC.
STEP 2.
Pull on the SRD strap located on the front right side of your full-body fall arrest
harness. (see Fig. 10)
STEP 4.
If you are able to reach your ladder or climbing system, use it to get back into
your secured treestand and then carefully climb down to ground-level. If you are not
able to reach your stand, remain calm and continue to stand in the SRD loop until help
arrives. (see Fig. 13)
STEP 3 .
Adjust the SRD strap so that you are able to step into the loop and then stand
up relieving the pressure on your lower extremities. The loop size can be adjusted by
moving the buckle up or down. (see Fig. 11 & 12)
STEP 5. Use your personal locating device or cell phone to call for help.
NOTE:
Several optional commercial products/systems are available that offer self-
recovery or self extraction from a fall when suspended in a full-body fall arrest harness.
Some systems automatically descend the user while others allow user control. One of
these products/systems can be considered for use as an additional safety precaution
against prolonged suspension and suspension trauma. Be sure to follow the manu-
manufacturers’ directions on the safe use of these products/systems.
FIG 10
FIG 11
FIG 12 FIG 13
result in serious injury or death!
7

FALCON - PART LIST
Part # Description Qty Part # Description
Foot Platform 1
2
1
1
1
XP15-0312 Plastic Coated Cable
Rear Frame Support
XP17-0127 Quick Hitch
1
Footrest
XP17-0142 1 1/4" Ratchet Strap 1
1
Seat Assembly
Seat Bar
XP15-0221 1" Ratchet Strap
XP15-0020
XP15-0009
Full-Body Fall Arrest Harness J300. CB
XP87-0005 1/4" x 1 1/4" Hex Bolt {A} 1
XP87-0069 5/16" x 2" Hex Bolt {B} 2
XP87-0057 5/16" x 2 1/4" Hex Bolt {C} 2
XP87-0071 5/16" x 2 1/2" Hex Bolt {D} 1
18
READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT.
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
Qty
8
Instruction Manual 1
Safety DVD 1
[A] 1/4"x 1 1/4" Hex Bolt
{1 Piece}
[B] 5/16"x 2" Hex Bolt
{2 Pieces}
1/4" Nylock Nut
{1 Piece}
Seat Tension Bolt
{1 Piece}
Allen Wrench
{1 Piece}
5/16" Nylock Nut
{7 Pieces}
5/16" Delta Nut
{1 Piece}
5/16" Delta Bolt
{1 Piece}
5/16" x 2 1/2" Snap Pin
{1 Piece}
Nylon Washer
{18 Pieces}
[C] 5/16"x 2 1/4" Hex Bolt
{2 Pieces}
[D] 5/16"x 2 1/2" Hex Bolt
{1Pieces}
1
1
XP19-0410
XP19-0411
XP19-0412
XP19-0414
XP19-0413
XP19-0415
XP87-0043 Seat Tension Bolt 1
XP87-0029 1/4" Nylock Nut 1
XP87-0047 5/16" Nylock Nut 7
XP87-0027 Nylon Washer
XP87-0040 Allen Wrench 1
5/16" Delta Nut 1
5/16" Delta Bolt 1
XP87-0133 5/16"x 2 1/2" Snap Pin 1
XP87-0125
XP87-0126
XP87-0102 5/16" Nylon Insert 4
XP87-0067 5/16"x 2 3/4" Hex Bolt {E}1
[E] 5/16"x 2 3/4" Hex Bolt
{1Pieces}
5/16" Nylon Insert
{4Pieces}

READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT.
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
9
FIGURE 1
STEP 2. Using (1) 5/16" delta bolt, (4) nylon washers and (1) 5/16" delta nut, con-
nect one end of each plastic coated cable to the rear frame support.
Secure with (1) 5/16" nylock nut. (Fig. 1)
STEP 3. Connect lower ends of plastic coated cables and the footrest to the
foot platform using (2) 5/16" x 2 1/4" hex bolts [C], (6) nylon washers and (2)
5/16" nylock nuts. Then attach the footrest to the foot platform using (2) 5/16"
x2" hex bolts [B], (4) nylon washers and (2) 5/16" nylock nuts. (Fig. 2)
ASSEMBLY INSTRUCTIONS
-THEFALCON -
NOTE: Steps 1–4 require you to
temporarily finger tighten nuts
ensure proper alignment.
Plastic Coated
Cable
[B]
[B]
[C]
[C]
[E]
Plastic
Coated
Cable
Foot Platform
Footrest
Rear
Frame
Support
5/16" Delta Bolt
5/16" Delta
Nut
STEP 1. Attach the rear frame sup-
port to the foot platform using
(1) 5/16" x 2 3/4" hex bolt [E], (2)
nylon washers, (2) 5/16" nylon
inserts and (1) 5/16" nylock nut
tighten securely. (Fig. 1)
5/16" Nylon
Inserts

READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT.
10
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
STEP 4. Securely fasten the seat assembly to the top of rear frame support
using (1) 5/16" x 2 1/2" hex bolt [D], (2) nylon washers, (2) 5/16" nylon inserts
and (1) 5/16" nylock nut. (Fig. 2) Assemble adjustable rear support by sliding
quick hitch into the rear con-necting tube. (Fig. 2)
STEP 5. Securely tighten every nut and bolt at this time.
NOTE: The snap pin will be used to set the desired length of the rear support. (Fig. 2)
Seat Assembly • Back
[A]
Seat Bar Seat
Tension
Bolt
Allen
Wrench
Seat Assembly
Snap Pin
Rear Frame
Support
Quick Hitch
[D]
FIGURE 2
SEAT ASSEMBLY
Using the included Allen Wrench unthread the
Seat Tension Bolt to desired seat firmness.
5/16" Nylon
Inserts

READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USING THIS PRODUCT. 11
This instruction manual complies with ASTM F2123 Standard Test Method for Treestand Fall Arrest Systems.
STEP 1. Select a straight healthy tree, onede-
void of dead branches with a minimum diame-
ter of 9” (23 cm) and one that does not exceed
22” (56 cm) in diameter.
STEP 3. Place the included ratchet straps on
your person (do not carry in hand).
STEP 2. With your climbing system which
meets or exceeds ASTM standards installed as
outlined in the Manufacturer’s Instruction
Manual, you are now ready to install your tree-
stand. Always maintain three points of contact
when climbing up/down climbing systems.
Always use a pull-up (hoist) rope to raise and
lower your treestand. Never climb with any-
thing on your back.
STEP 4. Tie your pull-up (hoist) rope to your
hang–on treestand in a way that you secure the
seat portion to the foot platform to keep the
treestand from opening when being hoisted.
Should the treestand open while being-
pulled-up (hoisted) it will become awkward and
dangerously clumsy.
STEP 5. Locate the quick hitch (Fig. 2 on page
10). Place the quick hitch somewhere on your
person. Do not attempt to climb with it in your
hand. Note: The snap pin should be installed in
the receiver portion of the treestand.
STEP 6. With your treestand attached to the
pull-up (hoist) rope, and the tag-end in your
possession (do not hold in hand), check to
ensure your linesman belt is properly secured
to you and the linesman/clilmbing belt is
attached to the tree and carefully climb to the
desired height.
FIELD INSTALLATION
-THECHAMP 2.0 -
STOP NOW! It will be necessary to use the climbing belt with your full-body fall arrest harness
while ascending the tree and attaching your treestand. As you climb it will be necessary to
slide the climbing belt up the tree. Once you’ve reached the desired height and your treestand
is properly secured to the tree, you will need to attach the permanent tree belt and secure
tether strap as illustrated on page 5 of this manual. FAILURE TO WEAR YOUR FULL-BODY FALL
ARREST HARNESS AT ALL TIMES WHILE USING THIS PRODUCT MAY RESULT IN SERIOUS INJURY
WARNING! Prior to installing your X-Stand hang-on treestand,you must install a climbing
system (i.e., stacking sticks,ladders,sectionals,etc.) which meets or exceeds ASTM standards.
Failure to follow these instructions may result in serious injury or death!
WARNING! DO NOT attempt to install this product on a tree that is not straight,healthy, and
devoid of dead branches,limbs,vines,or anything that might interfere with the installation. DO
NOT attempt to install this treestand on a tree that is leaning, diseased,crooked,ha sloose
bark, or does not meet the minimum installation diameter of nine (9) inches (23 cm) at tree-
stand height (i.e. seating platform height) or exceeds the maximum installation diameter of
twenty (20) inches (51 cm) at treestand height (i.e. seating platform height).
Failure to follow these instructions may result in injury or death!
-THEFALCON -

READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USINGTHIS PRODUCT.
12
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
STEP 8. Once you reach the desired treestand
installation height, re-check to ensure your
linesman/climbing belt is properly secured to
you and the tree. Make certain you are bal-
anced and secure on your climbing system.
Place the quick hitch on the tree trunk as
shown in Figure 1 on page 13.
STEP 9. Securing the loop end of the 1 1/4"
ratchet strap around the strap post on the quick
hitch.Then wrap the ratchet strap around the
tree and secure wrap the ratchet strap around
the tree and secureit to the opposite strap post
on the quick hitch (Fig. 1)
Make certain the ratchet straps is not twisted.
Note: If the ratchet strap is twisted, remove
and reattach so it is not twisted. Remove the
slack from the ratchet strap by pulling on the
tag-end of the strap. Engage the ratchet strap
and ratchet until the strap is tight.
STEP 10. With the quick hitch receiver installed
as previously outlined, pull up(hoist) your trees-
tand. With your treestand folded with the foot
platform in the upright position and firmly in
hand remove the hitch pin. Gently slide the tree-
stand receiver onto the quick hitch (Fig. 1).
Continue to slide the treestand onto the quick
hitch until the treestand is in a level
position.This is accomplished by selecting the
mounting hole which allows for level installa-
tion. When in a level position reinstall the hitch
pin (Fig. 1) make sure to engage the wire safety
clip. Untie the hoist rope and gently lower the
foot platform into a horizontal position engaging
the rear of the platform to the tree.
STEP 7. With your treestand attached to the
pull-up(hoist) rope and the tag-end in your pos-
session (do not hold in hand), check to ensure
your linesman/climbing belt is attached to the
tree and carefully climb to the desired height.
STEP 11. Lower foot platform to standing position;
the treestand will then snug up to the tree to prevent
any shifting. Hook one end of the 1" ratchet strap onto
the rear of foot platform, wrap the ratchet strap around
the tree trunk and secure the opposite hook to the rear
of foot platform and tighten securely to prevent shift-
ing. Carefully tighten the VITAL RATCHET STRAP
securely (see ratchet instructions blow). Repeat as
necessary to accomplish a snug fit to the tree. (Figure
2)
STEP 12. While remaining attached to the tree
with your linesman belt, attach the tree belt to
the tree trunk at a location above the seat. Both
the linesman belt for the tree belt of the full-body
fall arrest harness should be attached. Discon-
nect the linesman belt and climb above standing
platform and step down onto the center of the
standing platform. If there is any looseness, step
off the treestand and back onto the climbing
system. Disconnect the tree-stand and repeat
the previous installation STEPS after reconnect-
ing your linesman belt, lower seat.
VITAL RATCHET INSTRUCTIONS
STEP 1. Thread strap through slot in the center of the ratchet reel
is snug (Fig. 2)
(Fig. 1). Remove slack from strap by pulling loose end until the t
STEP 2.
Then ratchet handle back and forth to tighten straps, a
minimum of two (2) wraps around the ratchet reel is required (Fig. 3).
STEP 3. After strap is tight, close handle to the lock position.
STEP 4.
To remove tension, pull spring loaded retaining lock
and open ratchet completely, then manually pull strap to loosen
(Fig. 4).
2X Min.
FIGURE 1 FIGURE 2
FIGURE 3 FIGURE 4

READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USINGTHIS PRODUCT. 13
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
1 1/4" Ratchet Strap
1" Ratchet Strap
1" Ratchet
Strap
Strap Post
FIGURE 2
FIGURE 3
1 1/4" Ratchet
Strap
1 1/4" Ratchet
Strap
1 1/4" Ratchet
Strap
Rear Connecting
Tube
Quick Hitch
Strap Post
Loop
Quick Hitch
Snap Pin
Quick Hitch
Quick Hitch
Snap Pin
Rear Connecting
Tube
Rear Connecting
Tube
FIGURE 1
1 1/4" Ratchet
Strap
1" Ratchet
Strap
Change the position of the cables on
the rear frame support to adjust the
platform angle for level hunting.

X-Stand Treestands | 21673 Cedar Avenue South | Lakeville, MN 55044
ATTENTION!!WHEN YOU SEE A “WARNING!” BE SURE TO HEED THE
MESSAGE! THE INFORMATION CONTAINED IN THESE MESSAGES
CAN SAVE YOUR LIFE!!
READTHIS MANUAL IN ITS ENTIRETY PRIOR TO USINGTHIS PRODUCT.
14
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
To activate your product’s warranty, please mail in your registration card or submit it online at www. X-Stand.com
HANG-ON AND CLIMBING SYSTEM WARNINGS & PRODUCT REGISTRATION
Product Purchased Model Number
Serial Number
Owner’s Name
Street Address
City State Zip Code
E-mail Address Phone
Date Purchased
Purchased From (Dealer Name)
How did you hear about us: Catalog Webpage Friend Magazine
Other, Please Explain
Are you a: Bow Hunter Gun Hunter Both
Treestand Preference: Fixed Position Climbing Ladderstand
WARNING! DO NOT jump or bounce on the treestand platform (or any of the treestands
components) and/or the seat to engage the stand to the tree. Failure to follow these
instructions may result in serious injury or death!
WARNING! When installing your treestand,never attempt to climb with your treestand
in your possession. Always use a pull up rope to raise and lower the treestand during
installation and removal.NEVER ATTEMPT TO CLIMB WITH ANY HUNTING COMPONENT OR
ACCESSORY IN HAND OR ON YOUR BACK. Failure to follow these instructions may result in
serious injury or death!
WARNING! Climbing aids (e.g.,stick ladders,sectional ladders,etc.) must be installed
and extend a minimum of 24-inches (2 feet) above the seating platform. This practice
allows the user to have a firm hand hold when stepping down onto the platform. NEVER
attempt to step up onto your foot platform. Failure to follow these instructions may result in
serious injury or death!
WARNING! NEVER ATTEMPT to step onto a treestand until all treestand contact points
are secured tightly and firmly to the tree. NEVER ATTEMPT to step onto a treestand unless
your full-body fall arrest harness is properly attached. Failure to follow these instructions
may result in serious injury or death!
WARNING! When installing your hang on treestand,you must wear your full-body fall
arrest harness and use the climbing belt at all times while installing or removing your fixed
position treestand. The use of the climbing belt ensures your syable attachment to the tree
until installation is complete. Failure to follow these instructions may result in serious injury
or death!
WARNING! Never install,set-up,or climb to your treestand with a weapon. Use a pull-up
rope to carefully raise your unloaded weapon after full-body fall arrest harness is secure
and you are set in the stand!
WARNING! An ASTM compliant full-body fall arrest harness with a lineman’s/climbing
belt must be worn at all times while installing or removing any hangon style treestands or
climbing aids (i.e.,ladders,sticks,steps,etc.). Failure to follow these instructions may
result in serious injury or death!
WARNING! If you find that your treestand is unlevel, canted, angled awkwardly upward
or downward, or in any configuration other than level, immediately climb down to ground-
level and readjust your treestand as necessary to alleviate this awkward angle. Never
attempt to hunt from an unlevel treestand. Additionally, never attempt to level your
treestand at heights above the ground. Failure to foolow these instructions may result in
serious injury or death!

READ THIS MANUAL IN ITS ENTIRETY PRIOR TO USINGTHIS PRODUCT. 15
This instruction manual complies with ASTM F2123 Standard Practice for Treestand Instruction.
STANDARD LIMITED WARRANTY
Warranty: X-Stand™ Treestands warrant all X-Stand™ treestands, climbing system products and hunting
accessories to be free from defects in material and workmanship for a period of twelve months from
the original date of retail purchase. X-Stand™ Treestands warrants the enclosed hardware (where
applicable) is delivered to be free from physical defects for a period of twelve months from the original
date of retail purchase.
Repair Procedures, Exclusive Remedy: X-Stand™ Treestands will at its option, repair, or replace products
not conforming to this limited warranty at no charge. THIS IS THE SOLE AND EXCLUSIVE REMEDY
AVAILABLE FOR BREACH OF WARRANTY OR UNDER ANY OTHER LEGAL THEORY WITH RESPECT
TO X-STAND™ Treestands. If you find a product to be defective, contact the customer service
department at 540-877-2769 or email at [email protected]. When you receive authorization, return
the product as directed at your expense. Product repairs not covered by warranty, and product
updates, will be provided at a set rate.
Limitations: This warranty is void if the product is damaged by improper or abnormal use or by
accident; if the product is altered or modified in any way other than those di rected by official X-Stand™
Treestands instructions; or if any attempt is made to repair the product without authorization from X-
Stand™ Treestands. It is solely the purchaser’s responsibility to determine the suitability of these
products for each particular application. X-Stand™ Treestands products are intended for hunting and
hunting only. X-Stand™ Treestands are in all events not suitable, and are not authorized, for use in any
situations that might pose potentially injurious to life and health, other than those situations that the
products are intended for. This warranty is not assignable or transferable.
No Other Warranties: EXCEPT AS PROVIDED IN THIS LIMITED WARRANTY SET FORTH IN THE
WARRANTY CARD SUPPLIED WITH X-STAND™ TREESTANDS AND INSTRUCTION SHEETS ARE
PROVIDED “AS IS”. ALL OTHER WARRANTIES AND REPRESENTATIONS, ORAL OR WRITTEN,
EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXCLUDED AND DO NOT
APPLY. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE
HERE OF. Except as required by law, no representative, agent or employee of X-Stand™ Treestands is
authorized to make warranties, representations, or obligations inconsistent with or in addition to those
set forth in this limited warranty.
No Damages: IN NO EVENT WILL X-STAND™ Treestands BE LIABLE FOR DIRECT, INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM BREACH OF WARRANTY OR
UNDER ANY OTHER LEGAL THEORY, even if advised of the possibility of such damages. In no event
will X-Stand™ Treestands be liable for sums in excess of the purchase price of the product. X-Stand™
Treestands is thus not liable for lost profits or goodwill; downtime; damage or destruction of items or
equipment used with, or in conjunction with, X-Stand™ Treestands; personal injury or loss; or any
other damages.
General: (a) This agreement is the entire agreement between you and X-Stand™ Treestands.;
supercedes any prior or different agreements, representations, or proposals; and may be changed
only by written agreement with X-Stand™ Treestands. (b) Waiver by any party of any default or breach
of this agreement will not constitute a waiver of any subsequent default or breach of the same of
different kind. (c) The invalidity of any provision of this agreement shall not affect the validity of the
other provisions hereof. (d) This agreement shall be governed by the laws of the State of Minnesota,
U.S.A. X-Stand™ Treestands; Lakeville, MN 55044

Second Edition, April 2020, Published by X-Stand™ TREESTANDS, Lakeville Minnesota.
© 2019 X-Stand™ TREESTANDS. All rights reserved.
21673 Cedar Avenue South I Lakeville, MN 55044 I 540-877-2769 • [email protected]
This X-Stand™ product(s) has been tested to rigid industry standards. Safe operation and use of this X-Stand™ product(s) is the responsibility
of the user(s). Please read and follow all safe use instructions and warnings. Failure to follow these may result in serious injury or death!