Polar Electro G620-A User manual

15kg Ice Maker
Instruction manual
Model
G620-A

1
Telephone Helpline: 1300225960
Safety Tips
• Position on a flat, stable surface.
• A service agent/qualified technician should carry out installation and any repairs if required. Do not
remove any components or service panels on this product.
• Consult Local and National Standards to comply with the following:
• Health and Safety at Work Legislation
• BS EN Codes of Practice
• Fire Precautions
• IEE Wiring Regulations
• Building Regulations
• DO NOT immerse in water, or use steam washers to clean the unit.
• DO NOT cover the appliance when it is operating.
• Always carry, store and handle the appliance in a vertical position.
• Replace any unused water in the tank at least once every 24 hours.
•Forinternaluseonly.
• Keep all packaging away from children. Dispose of packaging in accordance to the regulations of local
authorities.
• If the power cord is damaged, it must be replaced by an POLAR agent or a recommended qualified
technician in order to avoid a hazard.
Introduction
Please take a few moments to carefully read through this manual. Correct maintenance and operation of
this machine will provide the best possible performance from your POLAR product.
Pack Contents
The following is included:
POLAR prides itself on quality and service, ensuring that at the time of packaging the contents are supplied
fully functional and free of damage.
Should you find any damage as a result of transit, please contact your POLAR dealer immediately.
•IceMaker
• Removable ice basket
•Icescoop
• Instruction manual

2
Telephone Helpline: 1300225960
Installation
1. Remove the appliance from the packaging and remove the protective film from all surfaces.
2. When positioning the appliance, maintain a distance of 20cm (7 inches) between the appliance and
walls or other objects for ventilation. Increase this distance if the obstacle is a heat source.
3. If necessary, adjust the screw legs of the appliance to make it level. The efficiency of the appliance
can be reduced if it is unevenly located.
Operation
Control Panel
Making Ice
Each time the appliance is refilled, the first ice making cycle is used to reduce the water temperature. This
results in uneven ice cube production which is perfectly normal. You may wish to discard ice created in the
first production cycle.
1. Lift the access lid and fill the water tank up the level of the ice basket shelf.
2. Connect the appliance to the power and press the START button.
3. Press the SELECT button repeatedly to scroll through the ice cube sizes. Stop when the required size is
illuminated.
4. The appliance will run a startup routine and then begin ice production.
5. When the cubes reach the ice sensor the appliance will stop production. Production resumes once ice
has been removed.
6. Press the STOP button at any time to halt the ice making process.
Note: If the appliance has not been stored or moved in an upright position, let it stand
upright for approximately 12 hours before operation. If in doubt allow the appliance to
stand.
Note: Before using for the first time, clean the water tank, ice basket and ice basket
shelf.
Note: Each ice making cycle takes between 6-12 minutes, depending on the size of cube
selected.
Note: If the water level is too low, the Water Low indicator lights up and the appliance
stops working. Fill the water tank and the appliance will restart automatically.
Ice cube size indicator

3
Telephone Helpline: 1300225960
Cleaning, Care & Maintenance
• Always switch off and disconnect the power supply before cleaning.
• Warm, soapy water is recommended for cleaning. Cleaning agents may leave harmful residues. DO
NOT wash the base unit, instead wipe the exterior with a damp cloth.
• A POLAR agent or qualified technician should carry out repairs if required.
• Clean the water filter regularly with a small brush, particularly in hard water areas. The water filter is
located in the pump inlet at the bottom of the water tank, remove by pulling out with fingers.
• If the appliance is to be left unused for longer than 24 hours, loosen the drain screw and drain the
water from the tank.
• The inner removable parts and water tank should be cleaned regularly.
Tro u b l e s h o o ti n g
Fault Probable Cause Action
The appliance is
not working
The appliance is not
switched on
Check the appliance is plugged in correctly and switched on
Plug and lead are
damaged
Call POLAR agent or qualified technician
Fuse in the plug has
blown
Replace the plug fuse
Power supply Check power supply
Internal wiring fault Call POLAR agent or qualified technician
Appliance is noisy
or works
intermittently
Power fluctuations Turn off the appliance and restart after 3 minutes
Water indicator is
lit
Water level is low or
tank is empty
Refill water tank and restart
Water filter is blocked Clean water filter and restart appliance
Ice Full indicator is
lit
Ice basket full Empty the ice basket
Room temperature is
too low
Move the appliance to a warmer position
Water and Ice Full
indicators flash
together
Water box is blocked
and cannot tilt
Disconnect from the power supply. Remove some of the ice
cubes and gently tilt the water box by hand. Restart the
appliance after 3 minutes
Ice cubes are
sticking together
Ice making cycle is
too long
Reset the ice cube size and restart the appliance
Water tank
temperature is too low
Empty water tank and refill
Compressor runs
but no ice is made
Refrigerant leak or
block in the
refrigerant system
Call POLAR agent or qualified technician

4
Telephone Helpline: 1300225960
Technical Specifications
Electrical Wiring
The plug is to be connected to a suitable mains socket.
This appliance is wired as follows:
• Live wire (coloured brown) to terminal marked L
• Neutral wire (coloured blue) to terminal marked N
• Earth wire (coloured green/yellow) to terminal marked E
This appliance must be earthed, using a dedicated earthing circuit.
If in doubt consult a qualified electrician.
Electrical isolation points must be kept clear of any obstructions. In the event of any emergency
disconnection being required they must be readily accessible.
Compliance
The WEEE logo on this product or its documentation indicates that the product must
not be disposed of as household waste. To help prevent possible harm to human
health and/or the environment, the product must be disposed of in an approved and
environmentally safe recycling process. For further information on how to dispose of
this product correctly, contact the product supplier, or the local authority responsible
for waste disposal in your area.
Polar parts have undergone strict product testing in order to comply with regulatory
standards and specifications set by international, independent, and federal
authorities.
Polar products have been approved to carry the following symbol:
All rights reserved. No part of these instructions may be produced or transmitted in any form or by any means,
electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of POLAR.
Every effort is made to ensure all details are correct at the time of going to press, however, POLAR reserve the right
to change specifications without notice.
Model Voltage Power Current
Water
Tank
Volume
Bin
Storage
Ice
Making
Capacity
Refrigerant Dimensions
h x w x d mm Weight
G620-A 220-240V
50Hz
150W 1A 3.9 litres 2 kg 15kg/
24 hours
R134a
95g
415 x 365 x 420 18 kg

DECLARATION OF CONFORMITY
I, the undersigned, hereby declare that the equipment specified above
conforms to the above Legislation and Standard(s).
Equipment
Type
Ice Maker
Model G620-A
Legislation C-Tick
AS/NZ 3820 Essential Safety Requirements for
Low Voltage Electrical Equipment
Standards EN 55014-1:2000 +A1
EN 55014-2:1997+A1
EN 61000-3-2:2000
EN 61000-3-3:1995+A1
AS/NZS 60335.2.24:2003+A1+A2+A3
AS/NZS 60335.1:2002+A1+A2+A3
Producer Name Polar
Producer
Address
15 Badgally Road
Campbelltown,
NSW 2560
Date 09/03/11
Signature
Full Name Richard Cromwell
Position Marketing Director

Notes •Remarques •Notas •Opmerkingen •Anmerkungen •Notas •Note

G620-A_A5_v2