Populas Equity Workstation EQ 361416 KBL User manual

Pa r t s I nc l u de d
Leg Package:
(2) Legs (A and B)
(2) Leg Top Plates
(2) Feet
(4) Toe Caps
(1) Top Crank Assembly
(1) Drive Shaft Assembly
(1) Hardware Bag
Keyboard Surface – Lift Package:
(1) Keyboard Surface –
Lift with Hardware
Table Package:
(1) Cross Brace
(2) Table Tops
Hardware Bag with:
(2) Cross Brace Brackets
(8) 3⁄8" Cross Brace
(4) #8 x 13⁄4" Wood Screws
(8) 1⁄4" x 3⁄4" Fasteners
(16) #10 x 1" Screws for
Leg Top Plates
(4) 5⁄16" x 1" Fasteners
(4) 5⁄16" Lock Washers
(4) Levelers (or optional casters)
(1) 5⁄32" Allen Wrench
(1) 3⁄16" Allen Wrench
Hardware
Tools Needed:
#2 Phillips Screwdriver or
Power Driver
EQUITY BI-LEVEL WITH KEYBOARD LIFT
Computer workstation with hand-crank adjustment
EQUITY BI-LEVEL WITH KEYBOARD LIFT
ASSEMBLY INSTRUCTIONS
Bracket Fastener
Instructions for models: EQ 361416 KBL, EQ 481416 KBL, EQ 601416 KBL, EQ 4230 CKBL

STEP ONE
Unpack and identify all parts.
Place table tops upside down on padded surface and identify front edge.
STEP TWO
Identify the legs (A and B) and their
orientation as shown in the diagram.
Look at the bottom of the leg to
identify the leg letter (A or B).
Legs must be positioned in correct
orientation to operate. Shaft
couplers face inward.
.
STEP FOUR
Attach feet to legs using two 5⁄16" button
head fasteners and lock washers per foot.
Insert toe caps and levelers.
Feet are offset to the front of
the table.
STEP THREE
Attach leg top plates to legs using four
¼" button head fastener per plate as
shown.
1⁄4" Button Head Fastener (x4)
Leg A
Leveler (x2)
Lock Washer (x4)
5⁄16" Button Head Fastener (x2)
Lock Washer (x2)
Leveler (x2)
Leg B

STEP FIVE
Attach cross brace bracket to cross brace
using four #8 13⁄4" screws as shown.
Attach cross brace bracket to legs
as shown.
#10 x 1 3/4" Wood Screw(x2)
B
#8 13⁄4" Wood Screw (x2)
3⁄8" Button Head Screw (x4)
Leg A
Leg B

Insert hexagonal shafts fully into legs
(front and rear).
Slide washer flush to connector tube and
center tube between legs.
STEP SIX
Attach mounting plates to tabletops using
#10 x 1" screws.
Attach Keyboard Surface-Lift using
#10 x 1" screws as shown.
STEP SEVEN
Gently turn table over and adjust levelers if required.
Insert the top crank handle through the rear table top directly into the crank tube. Keyboard surface lift raises and lowers
with front lever. Tilt adjustment is made with a knob.
Clean with soft cloth and mild cleaners suitable for furniture.
D
E
F
Leg A
Leg B
#10
x 1"
Screw (x4) #10 x 1" Screw (x3)
Detail: E Detail: F
# 10 x 1" Screw (x6)
#10 x 1" Screws (x6)
Detail : D