Populas VOX L-SHAPE DESK User manual

INFINITY 7230
WORKSTATIONS, DESKS, AND TABLES WITH POWERED ADJUSTMENT
PARTS INCLUDED:
LEG PACKAGE:
A (3) Telescoping
Legs
B(2) Feet
E (1) Controller
F (1) Control Switch
H (1) Table Mending
Plate
(1) Hardware bag
TABLE PACKAGE:
J (1) Main Work
Surface; (1) Return
Work Surface
TOOLS NEEDED:
Phillips Screwdriver
7/16" Open Ended
Wrench
HARDWARE BAG WITH:
L (12) M8 Fasteners
N (72) #10 x 1" Fasteners T(2) Double Threaded Rod
ASSEMBLY INSTRUCTIONS
P (20) #6 x 1/2" Fasteners
Q (2) #8 x 3/4” Fasteners
R
(4) Connector Caps
ASSEMBLY INSTRUCTIONS
O (20) Clamps (16 small, 4 large)
M (12) M6 Fasteners S(4) Curved Connector Plates
V
(8) 1/4”-20 Fasteners, Washers, and Nuts
(4) 1/4”-20 Nylon Stop Nut
C(1) Foot Plate
D
Instructions for Models: VX 7230 L, VX 727230 PC, VX 727224 PC, VX 727230 WC, VX 727224 WC
G (4) Cross Brace
Bracket
(5) Levelers
W
I
K(2) Cross Brace
(3) Table Support
Brace
U
VOX L-SHAPE DESK
Workstations, desks, and tables with powered adjustment
ASSEMBLY INSTRUCTIONS
XAllen Keys

STEP 1: PREPARATION
Unpack and identify all parts. Place Work Surfaces (J) upside
down on padded surface and identify Front Edge.
STEP 2: WORK SURFACE ATTACHMENT
Place Curved Connector Plates (S) in connector holes. Insert
Double Threaded Rod (T) into side holes of Work Surface.
Gently slide and align the two Work Surfaces together.
Secure the two Work Surfaces together with ¼”-20 Nylon
Stop Nuts (U).
Attach Table Mending Plate (H) to Work Surfaces using
sixteen #10 x 1 Fasteners (N) as shown. Insert four Connector
Caps (R) into connector holes.
Telescoping Legs
Mending Plate Foot Plate
Cross Brace
Controller & Switch
Work Surfaces
Support Braces
Feet & Levelers
Cross Brace Brackets

STEP 3: SUPPORT BRACE ATTACHMENT TO
TELESCOPING LEG
Position Table Support Brace (D) over Telescoping Leg (A) as
shown. Align the slot in the support brace with the cable exit
and securely attach cable in cable cradle. Secure Table
Support Brace to Telescoping Legs with four M6 Fasteners (M).
STEP 4: TABLE SUPPORT BRACE AND CROSS
BRACE ATTACHMENT TO WORK SURFACE
Position Table Support Braces (D) as shown with the cables
facing inward. Align with pre-drilled holes. Position Cross
Brace Brackets (G) on the back portion of Table Support Brace
(D). Position Cross Braces (K) and join to Cross Brace Brackets
(G) using ¼-20 Fasteners, Washers, and Nuts (V) as shown.
Attach Support Brace to Work Surface with six #10 x 1”
Fasteners (N). Attach Cross Braces (K) to Work Surface with
#10 x 1 Fasteners as shown.

STEP 5: CONTROLLER AND CONTROL
SWITCH ATTACHMENT
Position Controller (E) and Control Switch (F) as shown on Work
Surface. Align with pre-drilled holes and attach Controller to
Work Surface as shown using two #10 x 1” Fasteners (N). Plug
power cord into Controller (E). Plug each cable from the
Telescoping Legs (A) into the M1, M2, and M3 slots. Plug the
Control Switch (F) into the HS Slot. Attach Control Switch with
two #8 x ¾ Fasteners (Q). Control Switch can be mounted left or
right. Secure all cables and wires with Clamps (O) and #6 x ½”
Fasteners (P) as shown. Coil any excess cable.
STEP 6: FEET AND FOOT PLATE
ATTACHMENT
Attach Feet (B) to bottom of the outer Telescoping Legs (A), and
Foot Plate (C) over the center Telescoping Leg. Align with
mounting holes and attach using four M8 Fasteners (L) but do
not completely tighten. The mounting plate on the Telescoping
Leg will swivel allowing the feet to be aligned properly. Securely
holding the feet in the proper alignment with the Work Surface,
fully tighten the Fasteners. Position the Foot Plate (C) with
thread for Leveler facing inward. Attach ve Levelers (W) or
optional casters.
STEP 7: OPERATION AND USE
Caution: Desk is heavy and requires more than one person to
turn over. Gently turn table over and adjust Levelers (W) if
required. The table adjusts up and down using the Control
Switch (F). Clean with soft cloth and mild cleaners suitable for
furniture.

ASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
INFINITY
WORKSTATIONS, DESKS, AND TABLES WITH POWERED ADJUSTMENT
VOX SYSTEM CONTROLLER RESET PROCEDURE
The following instructions can be used to perform the reset procedure on Vox powered workstations.
These instructions should be used if a new controller is introduced to the system, the limits have
changed on the controller, or if the system is simply behaving unexpectedly. To reset the controller:
· Remove the motor cables from the “M” slots on the controller (M1, M2, etc.)
· Press and hold the down button on the switch until a “double click” is heard. This should
· Plug all motor cables back in to their respective “M” slots on the controller.
· Press the down button on the switch; at this point, all legs should begin slowly creeping
downward to the “zero” (fully retracted) position.
· Continue holding the down button until the system has reached its “zero” position. At this
point, press and hold the down button again, and the system will step forward to its“home”
position.
At this point, your Vox workstation should be reset to its home position. To verify, try operating the
system by moving it upwards with the up button, and again downwards; ensure the system returns to
the home position.
ASSEMBLY INSTRUCTIONS

OPTIONAL PROGRAMABLE CONTROL
SWITCH INSTRUCTIONS
launaMresU
3-ScigoL/2-ScigoL
4.2 Advanced Functionality
Note: Functionality described in this chapter is only accessible if you
have a handset with position keys and a save key !
4.2.1. Saving a Position
This function allows to save one desk-height per position key. To save a desk
position, proceed as follows:
Note: On initial operation all stored positions are equal to the lowest
possible desk-height (lower end position).
1.
Move the desk to the position you want to save.
The display reads the actual height of the desk (e.g. 73cm).
2.
Press the S key.
The display reads S –.
3.
Press the desired position key (e.g. T2).
The display reads S 2.
4. Now the height is saved on the chosen position key
The saving operation is conrmed with a double-click sound and
after appr. 2 seconds the storage height will be displayed.
Note: The position keys may have varying design, depending on the
kind of handset used.

OPTIONAL PROGRAMABLE CONTROL
SWITCH INSTRUCTIONS (CONTINUED)
launaMresU
3-ScigoL/2-ScigoL
4.2.2. Moving to a Saved Position
This function allows to move the desk to a saved position. To move to a saved
position, proceed as follows:
Note: Whether the double-click automatic function is available or not,
depends on the software conguration of the control box.
Alternative A (without automatic function)
1.
Press and hold the desired position key (e.g. 2).
The desk will move until the saved position is reached.
If you release the key before reaching the saved position, the
desk stops and the saved position will not be reached.
2. The desk has reached the saved height. Release the position key.
The display reads the actual desk-height.
Alternative B (with double-click automatic function)
1.
Double-click the desired position key (e.g. 2)
2. The desk automatically moves to the saved position.
The display reads the actual desk-height.
Note: If you press any key while the desk is automatically moving, the
desk will immediately stop. To continue, you have to repeat the above
procedure.