Populas Infinity 4836GT User manual

HARDWARE BAG WITH:
J(2) 1/2" Retaining Rings
K(8) 5/16"-18 x 1" Hex Head Fasteners
L (8) 5/16" Spring Washers
M (4) 1/4" x 1" Hex Head Lag Fasteners
N (4) 1/4" Spring Washers
O (9) #8 x 3/4" Phillips Fasteners
P (22) Clamps: (16 Small, 6 Large)
ASSEMBLY INSTRUCTIONS
Q (22) #6 x 1/2" Phillips Fasteners
S (2) Curved Connector Caps
R (2) 1/4"- 20 x 2" Hex Head Cap Fasteners
T (2) 1/4"- 20 Nylon Insert Stop Nuts
U (2) Connector Plates
V (4) Levelers (Or Optional Casters)
ASSEMBLY INSTRUCTIONS
PARTS INCLUDED:
LEG PACKAGE:
(2) Telescoping
Legs
(1) Motor Assembly
(1) Control Box
(1) Control Switch
(1) Hardware bag
TABLE PACKAGE:
(1) Table Support
Brace
(1) Table Top
(1) Foot Brace
(1) Cross Brace with
Hardware
TOOLS NEEDED:
Phillips Screwdriver
Slotted Screwdriver
7/16” Open Ended
Wrench
1/2” Socket Wrench
7/32” Hex Key Wrench
(For optional Casters)
INFINITY
WORKSTATIONS, DESKS, AND TABLES WITH POWERED ADJUSTMENT
INFINITY MULTA SERIES
Workstations, desks, and tables with powered adjustment
Innity 4836GT
Innity 7236
Innity 6648
Innity Command Center 6040CR
Innity Command Center 7234
These instructions apply to the following models:
2720 West Idaho Street Boise, ID 83702 Toll Free 800-957-2720 Fax [phone] www.populasfurniture.com
ASSEMBLY INSTRUCTIONS
A
B
C
D
E
F
G
H
I

Step 2: Piston Attachment
Insert hydraulic piston into center hole of Table
Support Brace (F) with piston top recessed inside
brace. Secure with 1/2" Retaining Ring (J), using pliers
to snap Retaining Ring into piston groove. Repeat for
second piston. Snap ring pliers and snap rings can be
used. Pull on piston to secure attachment.
Step 3: Telescoping Leg
Attachment
Insert piston foot into center of Telescoping Leg (A).
Piston hose port must route through "mouse hole"
of Telescoping Leg (A). Align Telescoping Leg (A) with
hose port facing center. Attach using two
5/16" -18 x 1" Hex Head Fasteners (K) and 5/16" Spring
Washers (L). Tighten using a 1/2" socket wrench. Do
not completely tighten until Step 4. Repeat for
second leg.
Step 1: Preparation
Unpack and identify all parts. Place Table Top (G)
upside down on padded surface and identify front
edge.
Be careful not to damage the hydraulic hose
Snap ring pliers Snap rings
Keep hose routed through mouse hole to
avoid pinch points
Short Hose
Foot Brace
Long Hose Motor Assembly
Telescoping Legs
Cross Brace
Table Brace
Control Box
and Switch
Front Edge
Table Top
Slotted groove on Telescoping Leg Faces in
Snap Ring
Piston
Piston Head
Table Brace
Hex Head Fasteners
Table Brace
Piston
Telescoping Leg
Piston Hose
Mouse Hole

Step 4: Foot Brace Attachment
Attach Foot Brace (H) to Telescoping Legs
(A) using two 5/16”-18 x 1” Hex Head
Fasteners (K) and 5/16”Spring Washers (L)
for each Telescoping leg (A), with Fastener
heads recessed inside Foot Brace (H).
Now tighten the four 5/16”-18 x 1”
Hex Head Fasteners from Step 3
Attach Floor Levelers (V). Optional Casters
attach using 3/8” button head fasteners.
Step 6: Table Support Brace
Attachment
Place Table Support Brace (F) and Motor
Assembly (B) on underside of table. Locate
three guide holes for Motor Assembly (B).
Position Telescoping Leg (A) with shorter
hose (A, Right). Align Table Support Brace (F)
to guide holes and attach using four 1/4" x 1"
Hex Head Fasteners (M) and 1/4" Spring
Washers (N). Tighten using 7/16” socket
wrench.
Do not over-tighten or strip
Step 5: Hand-crank Assembly
Positioning
Place Hand-crank Assembly (B) on table
as shown. Long Hose
Front Edge
Short Hose

Step 7: Motor Attachment
Align Motor Assembly (B) to three pre-drilled
holes and attach using three #8 x 3/4" Phillips
Fasteners (O). Route hoses through Small
Clamps (P) in pattern shown, and secure using
#6 x 1/2" Phillips Fasteners (Q).
Step 8: Control Box Attachment
Remove clip from Control Box (C) and attach
to the table (number side down) using two
#8 x 3/4” Phillips Fasteners (O). Carefully slide
Control Box (C) onto clip and fasten the
Control Box to pre-drilled holes using two
#8 x 3/4" Phillips Fasteners (O).
Step 9: Motor Placement
Plug motor wire into Control Box (C). Secure wires
with two Large
Clamps (P) using #6 x 1/2" Phillips
Fasteners (Q). Plug power wire into Control Box (C).
Secure one Small
Clamp (P) (for strain relief ) using
#6 x 1/2” Phillips fasteners (Q).
Small Clamps
Small Clamps
Large Clamps
Clip
Control Box

Step 12: Operation And Use
Gently turn table over and adjust levelers if required.
Table adjusts up and down using the control switch.
Clean with soft cloth and mild cleaners suitable for
furniture.
Step 10: Control Switch
Attachment
Attach Control Switch (D) to pre-drilled location
using two # 8 x 3/4" Phillips Fasteners (O). Control
Switch (D) may be positioned elsewhere depending
upon preference. Secure wire with Small Clamps (P)
and #6 x 1/2" Phillips Fasteners (Q). Insert Control
Switch (D) plug into Control Box. Coil the wire and
secure with four Large Clamps (P) using #6 x 1/2"
Phillips Fasteners (Q).
Step 11: Cross Brace Attachment
Hardware is shipped attached. Insert 1/4”-20 x 2”
Hex Head Fasteners (R) into rear slotted groove of
Telescoping Leg (A). Level Cross Brace (H) below
top of Telescoping Leg. Tighten using 7/16" wrench.
Cover connector hardware with Connector Cap (S).
Rear Slotted Groove
Control Switch