Porter 00196-010 User manual

INSTALLATION MANUAL
W ALL -M OUNTED C HINNING B ARS
No. 00196-010 and 00196-110
PARTS LIST
00196-010 00196-110
Item No. Part No. Quantity Quantity Description
1A FRME 00309 001 4 2 Support Bracket (End and Intermediate)
1B FRME 00310 001 1 Support Bracket (At Bar Connection)
2 ROND 00134 0E0 1 1 Bar Section – 1" Diameter x 10' Long
3 HDWE 09010 0E0 4 4 1/4" x 3/8" Lg. Set Screw
4 HDWE 06128 0E0 8 6 1/2" x 2-1/2" Lg. Hex Head Lag Screw
5 HDWE 05005 0E0 8 6 1/2" Flatwasher
6 HDWE 08021 000 8 6 Vinyl Anchor
Refer to Page 2 when building and installing one No. 00196-010 Chinning Bar as a stand-alone 10'-0" long unit.
Refer to Pages 3 and 4 when building and installing a Continuous Chinning Bar using one No. 00196-010 Chinning Bar and
additional No. 00196-110 Add-On Sections.
INST 00354 071
2010 PORTER ATHLETIC, INC. ALL RIGHTS RESERVED. 7-2-2010
SAVE THESE INSTRUCTIONS FOR FUTURE USE

2
No. 00196-010
Wall-Mounted Chinning Bar – 10'-0" Long Section
1. Check all items against Parts List on Page 1 to ensure all have been included.
2. Carefully slide four Support Brackets (1A) over Bar Section (2). Note that Support Brackets are spaced evenly along Bar Section
– 3' 3-1/2" on center. Ends of bar section will be flush with outside edges of support brackets. Finished length of Chinning Bar is
10'-0". See Detail "A".
3. Secure Support Brackets to Bar Section with 1/4" x 3/8" long Set Screws (3) – one Set Screw at each Support Bracket. Tighten
securely.
4. Mount Chinning Bar assembly to wall using hardware provided – 1/2" x 2-1/2" long Hex Head Lag Screw (4), 1/2" Flatwasher
(5) and Vinyl Anchor (6) – two at each Support Bracket. NOTE – Chinning Bar MUST be installed at a minimum height above
the finished floor, for safety. See Detail "A".
Detail "A" No. 00196-010 WALL-MOUNTED CHINNING BAR
1A
456
2
3
1'-212"
1'-112"
TO FLOOR
(MINIMUM )
1'-4"
CHINNING BAR TO WALL
CHINNING BAR MAY BE INSTALLED AT ANY
HEIGHT DESIRED. HOWEVER, FOR SAFETY
CONCERNS, CHINNING BAR MUST NEVER
BE LESS THAN 6'-8" ABOVE FLOOR.
3
6'-8"
5'-612"
TO FLOOR
(MINIMUM )

3
No. 00196-110
Continuous Wall-Mounted Chinning Bar – 10'-0" Long Add-On Section
1. Check all items against Parts List on Page 1 to ensure all have been included.
2. A continuous chinning bar can be built using a No. 00196-010 Chinning Bar as a starter section, and No. 00196-110 Chinning
Bars as add-on sections. As many additional No. 00196-110 Add-On Sections can be used as required, to build a chinning bar of
unlimited length. See Detail "B".
3. Identify the support brackets included with each No. 00196-110 Chinning Bar. Two brackets (1A) contain a short sleeve (with
one set screw hole), which the bar section slides through – these are for the end and intermediate positions. The third support
bracket (1B) contains a longer sleeve (with two set screw holes) – this bracket is located where two bar sections will be
connected.
No. 00196-110 SHOWN
AS RIGHT-END SECTION
No. 00196-110 SHOWN
AS CENTER SECTION(S)
QUANTITY AS REQUIRED
No. 00196-010 SHOWN
AS LEFT-END SECTION
Detail "B"
3'-314"3'-4" 3'-4"
10'-0" CHINNING BAR LENGTH
10'-0" CHINNING BAR LENGTH
10'-0" CHINNING BAR LENGTH
3'-4"
3'-314"
3'-4" 3'-4"
3'-4"3'-4"
One bracket from
No. 00196-010 is
used at far right-end
of continuous
chinning bar
Bracket from
No. 00196-010
Chinning Bar
21A 1A 1A
1B
1B
1A
1A
2
2
1A
1A 1A
No. 00196-010 and 000196-110
COMBINED TO BUILD A CONTINUOUS CHINNING BAR
NOTE - FOR CHINNING BAR LENGTHS OTHER THAN MULTIPLE 10'-0"
LENGTHS, THE 1" DIAMETER BAR SECTION MAY BE CUT IN THE FIELD
TO THE DESIRED LENGTH.

4
4. Carefully slide Support Brackets over Bar Sections. See Details "B" and "C". It is best to pre-assemble the continuous chinning
bar on the floor in 10' sections, as shown in Detail "B". NOTE – One Support Bracket from the No. 00196-010 starter section
will be used at the opposite end of the continuous chinning bar. See Detail "B".
5. Secure Support Brackets to Bar Sections with 1/4" x 3/8" long Set Screws (3). Note – support brackets at end and intermediate
positions (1A) require one set screw. Support brackets at bar connection require two set screws. Tighten securely.
6. Mount Chinning Bar assemblies to wall using hardware provided – 1/2" x 2-1/2" long Hex Head Lag Screw (4), 1/2" Flatwasher
(5) and Vinyl Anchor (6) – two at each Support Bracket. NOTE – Chinning Bar MUST be installed at a minimum height above
the finished floor, for safety. See Detail "C".
www.porterathletic.com
[phone]
SAVE THESE INSTRUCTIONS FOR FUTURE USE
1'-212"
1'-112"
CHINNING BAR TO WALL
1'-4"

TO FLOOR
(MINIMUM )
No. 00196-110 CONTINUOUS WALL-MOUNTED CHINNING BAR
456
Detail "C"
2
3
1B
3
1A
1A
1A
SUPPORT BRACKET
WITH LONGER
SLEEVE
(2 SET SCREWS)
TO FLOOR
(MINIMUM )
6'-8"
5'-612"
CHINNING BAR MAY BE INSTALLED AT ANY
HEIGHT DESIRED. HOWEVER, FOR SAFETY
CONCERNS, CHINNING BAR MUST NEVER
BE LESS THAN 6'-8" ABOVE FLOOR.