Portwell (R)PEB-4702VLA User manual

Quick Installation Guide
(R)PEB-4702VLA
Version 1.0
FORM FACTOR
Mini-ITX
CPU
μμFPGA 478
MEMORY
DDR2 2GB
LAN
Dual Intel
PCI-Express
Giga LAN
IDE
1 x UDMA 100
2 x SATA
AUDIO
AC'97 Codec
Expansion Bus
PCI-Express x 16
Mini PCI
CHIPSET
Intel 915GM
ICH6M
I/O
USB/Serial/LPT
Pentium M
2.26 GHz

22
22
2 Quick Installation
Copyright© 2005
All Rights Reserved.
The information in this document is subject to change without prior notice in
order to improve the reliability, design and function. It does not represent a
commitment on the part of the manufacturer.
Under no circumstances will the manufacturer be liable for any direct, indirect,
special, incidental, or consequential damages arising from the use or inability to
use the product or documentation, even if advised of the possibility of such
damages.
This document contains proprietary information protected by copyright. All rights
are reserved. No part of this manual may be reproduced by any mechanical,
electronic, or other means in any form without prior written permission of the
manufacturer.
About this Quick Installation Guide
This Quick Installation Guide provides general information and installation
instructions about the SBC. This User's Manual is intended for experienced
users and integrators with hardware knowledge of personal computers. If you
are not sure about any description in this User's Manual, please consult your
vendor before further handling.

33
33
3
Quick Installation
Warning
Single Board Computers and their components contain very delicate
Integrated Circuits (IC). To protect the Single Board Computer and its
components against damage from static electricity, you should always
follow the following precautions when handling it :
1. Disconnect your Single Board Computer from the power source when you
want to work on the inside
2. Hold the board by the edges and try not to touch the IC chips, leads or
circuitry
3. Use a grounded wrist strap when handling computer components.
4. Place components on a grounded antistatic pad or on the bag that came with
the Single Board Computer, whenever components are separated from the
system
Replacing the lithium batterReplacing the lithium batter
Replacing the lithium batterReplacing the lithium batter
Replacing the lithium battery
Incorrect replacement of the lithium battery may lead to a risk of explosion.
The lithium battery must be replaced with an identical battery or a battery type
recommended by the manufacturer (BR2032).
Do not throw lithium batteries into the trashcan. It must be disposed of in
accordance with local requlations concerning special waste.
TT
TT
Technical Supporechnical Suppor
echnical Supporechnical Suppor
echnical Support
Please do not hesitate to call or e-mail our customer service when you still can
not find out the answer.
http://www.portwell.com
E-mail:tech @portwell .com

44
44
4 Quick Installation
Warranty
This product is warranted to be in good working order for a period of two years
from the date of purchase. Should this product fail to be in good working order
at any time during this period, we will, at our option, replace or repair it at no
additional charge except as set forth in the following terms. This warranty does
not apply to products damaged by misuse, modifications, accident or disaster.
Vendor assumes no liability for any damages, lost profits, lost savings or any
other incidental or consequential damage resulting from the use, misuse of, or
inability to use this product. Vendor will not be liable for any claim made by any
other related party.
Vendors disclaim all other warranties, either expressed or implied, including but
not limited to implied warranties of merchantibility and fitness for a particular
purpose, with respect to the hardware, the accompanying product's manual(s)
and written materials, and any accompanying hardware. This limited warranty
gives you specific legal rights.
Return authorization must be obtained from the vendor before returned merchan-
dise will be accepted. Authorization can be obtained by calling or faxing the
vendor and requesting a Return Merchandise Authorization (RMA) number.
Returned goods should always be accompanied by a clear problem description.

55
55
5
Quick Installation
Before up and running, please make sure the package contains all of above
accessories. If any of the above items is damaged or missing, contact your
vendor immediately.
(R)PEB-4702VLA Mini ITX Embedded board
(R)PEB-4702VLA PACKING LIST
1 x I/O Bracket
1 x CPU cooler or Heat Sink
1x ATX Power Cable 300mm
1 x CD-ROM (System Driver)
Quick Installation Guide
Warranty card
Ordering Information
(R)PEB-4702VLA Mini-ITX Intel Pentium M socket 478 Embedded board with
CRT/LCD/DVI/Dual Gigabit Ethernet
Cable Kit IDE; USB; K/B-M/S; TV_Out; Print; SATA; LPT to FDD

66
66
6 Quick Installation
Product Name (R)PEB-4702VLA
Form Factor Mini-iTX Embedded Board Size (170mm x 170mm)
Processor μFC-PGA478 pin Pentium-M Dothan Up to 2.26GHz(533MHz FSB)
Chipset NB : Intel 915GM SB: Intel ICH6M
System Memory Support Two 240Pin DDRII SDRAM DIMM Socket Up to 2GB
UMA 915GM Video Controller with DVI, LVDS, TV-out and CRT support
(Support Dual Independent display)
Ethernet Dual Intel 82573V Gigabit Ethernet
I/O Chips WINBOND W83627HG
BIOS Phoenix-Award PnP Flash BIOS
Audio AC'97 Codec, supports MIC-In/ Line-In/ Line-out
Serial ATA 2 x Serial ATA with 150MB/s transfer rate
ATA / IDE 1 x Ultra DMA 100, support 2 IDE devices
Flash Disk 1 x Type II Compact Flash Disk Socket (Share IDE Resource)
2 x COM ports
COM 1: RS-232
COM 2: RS232/422/485 Select
Parallel Port Supports SPP/ EPP/ ECP mode
K/B and Mouse 1 x PS2 K/B and Mouse
USB Port 8 x USB 2.0
DIO 8 bit programmable Digital I/O
TV out 6 pin mini wafer
LCD 18/36 bit LVDS
PCI-Express x 16 slot for High-Performance Graphics Card or PCI-Express
x1 Device
1 x Mini PCI socket
Hardware Monitor
Chip Integrated in W83627HG
RTC Support Real Time Clock
ATX 12V Power Connector
DC-IN 12V Power Adapter
Opera tion Temp. 0ºC ~ 60ºC
Wa tchdog Timer 255-level Reset
Dimension (L x W) 170 x 170 mm (6.7" x 6.7")
Specification
VGA/LCD Controller
Power Input
Connector
Serial Port
Expansion Interface
Note:
1. Recommend use ATX power to instead of 12V DC-IN if there's a PCI
Express x16 Graphics card on the board
2. DC-12V Output: Strongly recommend output upper then 80W

77
77
7
Quick Installation
Board Layout
JFSB1

88
88
8 Quick Installation
Board Dimension

99
99
9
Quick Installation
Jumper/Connector Quick Reference
Label Function
JBAT1 Clear CMOS
JRS1 COM2 RS-232/422/485 Select
JVLCD1 LVDS1 LCD Voltage select
JFSB1 Front side bus clock select

1010
1010
10 Quick Installation
Jumper/Connector Quick Reference
Label Function
ATX12V1 ATX 12V DC Input
PWR1 4P Auxilary Power Connector (for output only)
AUDIO1 Audio interface Port
CPUF1 CPU FAN Connector
SYSF1 System FAN Connector
DIMM1,2 240 Pin DDR2 DIMM Socket
DIO1 Digital I/O Connector
IDE1 Primary IDE Connector
PCIE1 PCI Express x 16 Interface Slot
MPCI1 Mini PCI Interface
LVDS1 LVDS LCD Panel Connector
INV1 LCD Inverter Connector
IR1 Infrared (IR) Connector
TV1 TV-out Connector
SATA 1, 2 Serial ATA 1, 2 Connector
LPT1 Parallel Port or Floppy
CON1 RS-422 / 485 USB Connector
USB1, 2 USB Connector
KBM1 PS/2 Keyboard and Mouse
VGA1 CRT Display & DVI Connector
LAN1, LAN2 Ethernet ConnectorUSB1/2 + LAN1, LAN2 Connector
DCIN1 DC-12V Power Adapter In
JFRT1 Front Panel (Switches and Indicators)
CFD1 Compact Flash Socket
JPWR1 AT/ATX Power Type Selection
VGA1 CRT SVGA Connector
Note:
1. LPT/FDD select by BIOS
2. Compact Flash share by IDE1 resources,can not Hot swap