POSIFLEX PS-3416 User manual

1
Package Contents
Fanless LCD touch terminal (x1)
Power adaptor (x1)
Power cord (x1)
User Manual (x1)
Recovery DVD (x1)
(for pre-loaded OS model only)
FCC NOTES
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
CE CLASS A WARNING
This equipment is compliant with Class A of CISPR 32. In a residential environment this
equipment may cause radio interference.
WARRANTY LIMITS
Warranty will terminate automatically when the machine is opened by any person other than
the authorized technicians. The user should consult his/her dealer for the problem happening.
Warranty voids if the user does not follow the instructions in application of this merchandise.
The manufacturer is by no means responsible for any damage or hazard caused by improper
application.
警告使用者
此為甲類資訊技術設備，於居住環境中使用時，可能會造成射頻擾動，在此種情況
下，使用者會被要求採取某些適當的對策。
SAFETY INSTRUCTIONS
This equipment is not suitable for use in locations where children are likely to be present.
PS-3416/3416E
Fanless LCD Touch Terminal
User Manual
13120901030 Ver. C0

2
CONSIGNES DE SÉCURITÉ
Cet équipement ne convient pas à une utilisation dans des lieux pouvant accueillir des
enfants.
BATTERY CAUTION NOTES
Dispose of used batteries according to the instructions.
Replacement of a battery with an incorrect type that can defeat a safeguard (for
example, in the case of some lithium battery types)
Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a
battery that can result in an explosion.
Leaving a battery in an extremely high temperature surrounding environment that
can result in an explosion or the leakage of flammable liquid or gas.
A battery subjected to extremely low air pressure that may result in an explosion or
the leakage of flammable liquid or gas.
BATTERIE ATTENTION NOTES
Jetez les piles usagées conformément aux instructions.
Remplacement d'une batterie avec un type incorrect qui peut annuler une sauvegarde
(par exemple, dans le cas de certains types de batterie au lithium)
Mise au rebut d'une batterie dans le feu ou dans un four chaud, ou écrasement ou
coupure mécanique d'une batterie pouvant entraîner une explosion.
Laisser une batterie dans un environnement environnant à des températures
extrêmement élevées pouvant entraîner une explosion ou la fuite de liquide ou de
gaz inflammable.
Une batterie soumise à une pression atmosphérique extrêmement basse pouvant
provoquer une explosion ou une fuite de liquide ou de gaz inflammable.
警告
本電池如果更換不正確會有爆炸的危險，請依製造商說明書處理用過之電池。
Views of the PS-3416/3416E
Front View
P-CAP Touch Panel
Gen 7E Base
LED Indicator

3
Rear View
Left Side View Right Side View
Bottom View
MSR Port Cover
Bottom I/O Cover
Power Button
Brightness
Adjustment Button “+”
Brightness
Adjustment Button “-”
HDD Cover
Rear I/O Cover
Hinge for LCD
Neck Cover
Cable Cover
Cable Exit
2nd Display
Screw Hole

4
View of I/O Interface
Top I/O Ports Rear I/O Ports
1
COM4 Port
3
Parallel (LPT) Port
Connector
2
USB 2.0 Port
4
PS/2_KB Pin Header
※ The top I/O ports are provided for COM-based and USB-based peripheral
devices, for example, customer display.
Bottom I/O Ports
1
RJ45 LAN Port
2
USB 2.0 Port
3
VGA Port
4
COM Port
(COM3/COM2/COM1)
5
RJ11 Cash Drawer Port
6
12VDC-IN Power Jack
Terminal from shipping mode to operation mode
In consideration of proper packaging, before shipping, the terminal is folded,
staying in shipping mode. Thus, when receiving the product, you will find that
the terminal is well folded, as shown below.
1
2
3
4
1
2
3
4
5
6

5
Before operating this terminal, unfold it and make this terminal rise in
operation mode by referring to the following steps. Here, an equivalent model
with GEN 7 base is taken below for example.
1. Firstly, lift this terminal gently to make it
to be unfolded.
2. Overturn this terminal in the direction as
indicated by the arrow in the right figure.
3. Place this terminal on a flat table.
4. Tilt this terminal to a degree in the direction as indicated by the arrow
below.

6
5. Remove the cable cover from the base.
6. Fix the base with two #/6/32-14L screws.
7. Push the cable cover back to the base.
Terminal from operation mode to shipping mode
To fold this terminal, refer to the following steps. Here, an equivalent model
with GEN 7 base is taken below for example.
1. Remove the cable cover.
2. Remove the two screws from the base.

7
3. Carefully hold the lower rim of the display.
4. Push the base-folding lever in the direction as indicated by the arrow
below (1). Then, the display will be loosen and go down (2).
5. When the display goes down to a degree, loose the base-folding lever, as
shown in the direction as indicated by the arrow below.
6. Then, gently tilt the display in the direction as indicated by the arrow
below until the display is well folded.
1
2

8
7. Put back the cable cover.
Installing Optional Upgrade Kits and Peripherals
PS-3416/3416E can work with multiple optional upgrade kits and peripheral
devices, such as magnetic stripe reader (MSR), LCD monitor, cash drawer and
the like.
Before installing an optional upgrade kit and/or peripheral device, make sure
that the system is powered off and the external power source is removed from
the POS box to prevent electric hazard! Failure to follow the warning
description will void the product warranty!
For the detailed instruction, refer to each of the user manuals of the optional
upgrade kits and peripheral devices.
Connecting Power Adapter and I/O Cables
Before connecting power adapter and I/O cables to the I/O ports of PS series
terminal, please route and arranging the cables. Refer to the following step-by-
step instruction of cable routing and arrangement for the details. Here, an
equivalent model with GEN 7 base is taken below for example.
1. Press the circled section of the cable
cover with your thumb.

9
2. Pull out the cable cover.
3. Push and tilt the terminal to the end in
the direction as shown by the arrow.
Then determine that the terminal is tilted
to the end, as shown in the right figure.
4. Press the circled section with two
thumbs and pull by force the two sides
of the locking hook with two forefingers
as indicated by the arrow.
5. Remove the neck cover from the base
stand.
Pull out

10
6. Tilt the terminal slightly at a little angle in the direction as shown by the
arrow, making cables easily pass through the cable passage.
7. Make the connector, which will be connected to the I/O port of the
terminal, pass through the cable passage of base stand.
8. Push and tilt the terminal to the
end in the direction as shown by
the arrow.
Cable Passage

11
9. Remove the bottom I/O cover
with your forefinger inserting
the middle hole of the cover.
10. Connect the connector of the
power adapter to the 12VDC-IN
power jack.
11. Cover the bottom I/O interface and gather the I/O cables to the circled
cable arrangement area, as shown below.
12. Push and tilt the terminal to the end in the
direction as shown by the arrow.

12
13. Arrange well the I/O cable located at the
area of neck cover.
14. Shield the I/O cable arrangement area on the neck of the base stand with
the neck cover.
15. Shield the I/O cable exposure area with the cable cover.
CAUTION: On doing insertion or extraction of a cable connector, please always
hold the connector head itself instead of pulling the cable wire. Doing this could
damage the cables and ports, which is considered as an artificial damage and is
not covered by the warranty. The means of power cord should be connected to a
socket-outlet with earthing connection.
ATTENTION: Lors de l'insertion ou de l'extraction d'un connecteur de câble,
veuillez toujours tenir la tête du connecteur elle-même au lieu de tirer le fil du
câble. Cela pourrait endommager les câbles, ce qui est considéré comme un
dommage artificiel et n'est pas couvert par la garantie. Le cordon d'alimentation
doit être connecté à une prise de courant avec mise à la terre.

13
Powering ON the PS-3416/3416E
After connecting the power cable to the power jack of the
terminal, press the power button to power on the terminal. To
power it off, press the power button again.
Once powering off the system, if you want to power it on
again, please wait at least 3 seconds.
If the system hangs due to a reason, such as software resource conflict, please
press and hold the power button for over 10 seconds to forcedly shut down the
system.
Power LED Indicator
LED status indicator, which is located at the lower right side of the LCD panel,
is mainly responsible for notifying users of the current system status by
emitting various LED signals. The table provided below shows all the possible
LED status as a quick reference.
LED
Status
Description
POWER
Solid blue
System power ON
Solid orange
System standby
Installing an Operating System
This product is highly professional equipment. Therefore, we do NOT
encourage you to install any operating system into this machine without
professional assistance. We shall not be responsible for any technical support
to questions on this aspect. We suggest that you contact your dealer for OS
installation.
Operating System Recovery
For the PS-3416/3416E main system preloaded with an operating system on
HDD or SSD, We provide a recovery DVD shipped with the main system for
the preloaded operating system. The system integrator shall take care of
software restoration after the OS is recovered.
If you plan to recover your operating system, we do NOT encourage you to
recover any operating system. Please contact your service center for operating
system recovery.
Operation Environment
This terminal must NOT be operated in an environment with restricted
ventilation. There must be at least 25 mm air clearance around any top or side
ventilation holes with free flow of air around the unit at all times for system
operation.

14
Specifications
System
Configuration
Processor
PS-3416:
Intel® Celeron J1800, 2C, 2.41GHz/2.58GHz
(Burst), 1M Cache
PS-3416E:
Intel® Celeron J1900, 4C, 2.00GHz/2.42GHz
(Burst), 2M Cache
System
Memory
SO-DIMM x 1, DDR3L
Storage Device
SATA x 1 + mSATA x 1
Power Supply
12V/40W
(upgrade to 60W or higher when required)
OS support
Windows 7 / POSReady 7 /
Windows Embedded 8.1 Industry /
Windows 10 IoT 64-bit / DOS /
Linux per request
Display & Touch
LCD
Bezel-free TFT LCD
Resolution
1024 x 768
Touch
Projected-capacitive touch
I/O & Expansion
Serial Port
4, 3 x DB9 on bottom I/O plate + 1 x RJ50 on top I/O
plate, 5V/12V support on all COM ports
Parallel Port
1, via optional conversion cable
Standard USB
Port
5, 4 on bottom I/O plate + 1 on top I/O plate
LAN Port
10 / 100 / 1000 Mb x 1
Display Port
VGA x 1, 12V support
CR Port
1, control 2 CR via optional Y-cable
PS/2 Port
Pin header inside service window
Audio
Buzzer only
Base Stand
7th generation foldable base stand
Power Supply
12V/40W
Environmental
Operating
Condition
0°C - 40°C, 20%RH - 90%RH (Equipped with
HDD);
0°C - 50°C, 20%RH - 90%RH (Equipped with SSD)
Storage
Condition
-20°C - 70°C, 10%RH - 90%RH
※ The product information and specifications are subject to change without
prior notice. To get the detailed information on the PS-3416/3416E,
please contact your dealer and the service team.

15
<MEMO>

16
<MEMO>