Posturite DeskRite 350 User manual

DeskRite 350
Electric Sit-Stand Desk
Assembly Instructions

Warning!
Do not swap control boxes between
desks. Only connect power cable when
desk is fully assembled. Power adapter
only for use on your desk.
Control Box
Desk Top
Power
Cable
Desk Switch
Assortment of
Cable Clips and
Cable Ties
Recommended
people for
assembly: 2
Contents
Estimated time
to assemble:
20 minutes
A B C D E F G H I
8 x
15mm M6
Hex Bolt
8 x
20mm M6
Hex Bolt
4 x
Adjustable
Feet Base
4 x
15mm M8
Hex Bolt
2 x
17mm ø5
Screws
6 x
45mm ø4.5
Screws
4 x
60mm ø5
Screws
2 x
Washers
2 x
18mm ø4
Screws
2 x Desk Legs
2 x Desk Feet
2 x Desk Top
Support Arms
2 x Cross Bars
Allen Key
Your package is likely to contain extra fastenings, should you need spares.

1.
2.
Loosen the bolts in the head of the
desk leg, slide the cross bars into
place and retighten the bolts with
the allen key provided.
Note: you may need to extend the
cross bars to reveal the attachment
slots and bolt holes.
Repeat on the opposite side until both
sides are tightly screwed together.

3.
4.
BC
Attach the desk feet to the legs
using the bolts (B) and allen key
provided.
Screw in the adjustable base
feet x 2 (C) into the desk foot.
Repeat on the opposite side
of the desk for the other leg.
Repeat on the opposite side. Once
assembled, turnover the frame over
so it is standing upright.

5.
6.
D
Use the bolts (D) to attach the desk
top support arms to the desk frame.
Ensure they are securely fastened
using the allen key provided.
Repeat on the opposite side.
Adjust the width of the telescopic crossbars to
accomodate the appropriate desk width required.
Loosen and tigthen the hex bolts with the allen key.

7.
8.
G
F
H
Line up the holes on the desk
top and support arms. Use
the bolts (A) to secure the
desk top into place.
Using the screws (G) and washers (H)
attach the cross bar to the desk top in
the centre where the bar is narrower.
Use the longer screws (F) to secure
the cross bar where the cross bar is
wider, as shown in diagram.
A

Use the screws (E) to screw the
control box to the centre of desk
top between the cross bar.
9.
10.
E
Plug in the power cable and
use the provided cable clips
and ties to keep the cable
secure and tidy.

12.
Using the screws (I) attach
the switch to the front edge
of the desk as shown.
11.
Connect the switch to
the control box.
I

13. Connect the leg cables into
the control box as shown in
the diagram below.
14.
Tidy up all the cables using the
clips and ties provided.
Plug into the mains power. Your
desk is now fully assembled.

Once finished you can
place your office
equipment on the desk.
This desk can hold up
to 100kg of weight.

1. Once you’ve assembled the desk, you will need to calibrate the electronic
motor. To do this, lower the desk to its lowest setting by pressing the down (-)
button. Now the desk is ready to be adjusted to a suitable height for you.
2. To find the right sitting or standing height, use the down (-) and up (+) button
Make sure your forearms are at a comfortable 90 degree angle to your body
while you type.
3. As the desk is designed to be regularly switched from sitting to standing, the
motor is designed for intermittent but not continuous use. Too much use will
trigger ‘cool down’ mode. If your desk is equipped with a display, the words
‘cooling time’ will display. Once the motor is cool again you’ll be able to
resume use.
4. This desk is equipped with anti-collision technology. That means if it detects an
obstacle while in transit, the mechanism will automatically stop and reverse a
few centimetres.
5. If your desk stops working, it may need to be recalibrated. First, check that
your desk is properly connected to the power supply. Next, disconnect one of
the cables from the control box, leave for 5 seconds and plug it back in. You
will then need to recalibrate the desk (see step 1).
6. If you’re still experiencing problems or having doubts, disconnect the desk
from the power supply and call our DSE help Team on 0345 345 0016.
Once assembled...

Other ergonomic office products available
Penguin
Ambidextrous Vertical Mouse
Number Slide Keyboard
with retractable number pad
MultiLite
Document Holder and Writing Slope
MoovRite
Rocking standing platform
Opløft
Sit-stand platform
Vision
Laptop/Tablet Stand
[phone]
[email protected]
posturite.co.uk