pottery barn kids UNIVERSAL TRUNDLE User manual

Date: 26-March-2012(Rev) Page 1/4
Rev: 1-Dec-2015
pottery barn kids
UNIVERSAL TRUNDLE
WARNING:
When using trundle for sleeping, trundle bed must be pulled away entirely from
the bed structure to prevent any entrapment issues. Make sure area surrounding
the trundle bed is clear of any hazard.
PRE-ASSEMBLY:
 For your safety and ease, assembly by two adults is recommended.
 Please read all instructions before beginning assembly. The illustrations provided allow for easier assembly
when used in conjunction with the assembly instructions.
 Remove all parts and hardware from box and lay out on a carpeted or scratch-free work surface. The shipping
box provides and ideal work surface. Do not dispose of any contents until assembly is completed to avoid
accidentally discarding small parts or hardware.
 Use the parts and hardware lists to identify and separate each of the pieces included prior to starting
assembly.
 Note: DO not fully tighten the bolts until all parts are in place. Failure to follow these instructions may cause
the bolts to misalign during assembly.
 If using power tools to aid in assembly please use caution. Power tools can damage hardware or split wood.
HARDWARE INCLUDED:
(F) Allen Key – 1pc
(G) Bolt ¼” x 60mm – 8pcs
(H) Spring Washer – 8pcs
(I) Flat Washer – 8pcs
(J) Barrel Nut – 8pcs
(K) Long Wood Screw 4 x
30mm – 22pcs
(L) Short Wood Screw 4 x
13mm – 24pcs
(M) Caster – 6pcs
HARDWARE LIST
A.
B.
E.
E.
PARTS INCLUDED:
(A) Left and Right Board (with extra holes)– 2pcs
(B) Center Bottom Board – 1pc
(C) Cross Bar – 2pcs
(D) Long Side Rail – 2pcs
(E) Short Side Rail – 2pcs
TOOLS REQUIRED:
Philips Head Screwdriver (Not included)

Date: 26-March-2012(Rev) Page 2/4
Rev: 1-Dec-2015
ASSEMBLY INSTRUCTIONS:
1. Please make sure bed side rails set on highest level for use with trundle.
2. Lay the Left and Right Bottom Boards (A) on either side of the Center Bottom Board (B) with the pre-drilled
holes facing up, as shown below.
3. Attach (2) Cross Bars (C) to the bottom boards by inserting (6) Long Wood Screws (K) into the pre-drilled
holes of each cross bar, tightening with the Philips Head Screwdriver.
C.
K.
K
(12x)

Date: 26-March-2012(Rev) Page 3/4
Rev: 1-Dec-2015
4. To Attach Long Side Rails (D) to the assembled piece, insert the wooden dowels on the ends of the
Cross Bars (C) into the pre-drilled holes on the Long Side Rails (D), as shown below. Press firmly to
ensure the Left and Right Bottom Boards (A) sit in the slots of the Long Side Rails (D).
5. Slide a Spring Washer (H) and a Flat Washer (I) onto each Bolt (G). Align the predrilled holes on the
Short Side Rails (E) to the wooden dowels on ends of the (2) Long Side Rails (D). Insert the bolt with
washers into pre-drilled hole on the Short Side Rail (E). Place Barrel Nut (J) in the corresponding
opening on the Long Side Rail and use Allen Key (F) to connect, as shown below. Repeat with the
remaining (7) bolts. Do not fully tighten the bolts.
G
(8x)
A.
A.

Date: 26-March-2012(Rev) Page 4/4
Rev: 1-Dec-2015
6. Secure Bottom Boards with the Long/Short Side Rails by inserting the remaining (10) Long Wood
Screws (K) into pre-drilled holes on wooden cleats and tighten with a Philips Head Screwdriver as shown.
7. Attach the (6) Casters (M) to pre-drilled holes on the Bottom Boards using (24) Short Wood Screws (L)
and tighten with a Philips Head Screw Driver. Check alignments and tighten all connecting bolts.
CARE INSTRUCTIONS:
 Dust often using a clean, soft, dry lint-free cloth.
 Blot spills immediately, and wipe with a clean, damp, cloth.
 We do not recommend the use of chemical cleansers, abrasives, or furniture polish on our lacquered
finish.
Thank you for your purchase.
stores | catalog | www.potterybarnkids.com
USA 1.800.290.8181
K.
L.
M.
K
(10x)
L
(24x)