PotteryBarn CLARA FULL BED User manual

Page 1/ 6
CLARA FULL BED
ASSEMBLY INSTRUCTIONS
Date: 2014-Oct.-16
Rev: www.potterybarn.com

Page 2/ 6
Important Safety Instructions:
Please read all instructions carefully before assembling.
For your safety, assembly by two or more adults is strongly recommended.
Keep these instructions for future use.
Use only vendor-supplied hardware to assemble this item. Using unauthorized hardware could jeopardize the
structural integrity of the item.
Pre-assembly:
Remove all parts and hardware from the box. Place all items on a carpeted or scratch-free work surface, as this
will avoid damaging parts during assembly. The shipping box provides an ideal work surface.
To avoid accidentally discarding small parts or hardware, do not dispose of any packaging or contents of the
shipping carton until assembly is complete.
Use the parts and hardware lists below to identify and separate each of the pieces included.
The illustrations provided allow for easier assembly when used in conjunction with the assembly instructions.
The use of power tools to aid in assembly is not recommended. Power tools can damage the hardware and split
the wood.
Parts Included:
Hardware Enclosed:
E- Flat Washer – 12x F- Spring Washer – 12x G- ShortAllen Bolt – 12x H- Allen Key – 1x
M6x25 mm
I- Wood Screw – 32x
4x30 mm
Tools Required (not included):
Philips Head Screwdriver
A- Headboard – 1x
B- Footboard – 1x
C- Side Rail – 2x
D - Slat Roll – 1x

Page 3/ 6
Assembly Instruction Steps:
Note: The mattress support on the side rails is pre-assembled in the low position when shipped to allow bed to be
used with a box spring mattress. If you intend to use your bed without a box spring, the extra mattress support rail
will have to be raised at the higher position on side rails. Follow Step 13 and onward if you intend to use bed without
a box spring
1. Attach the 2 Side Rails (C) to Headboard (A) by aligning the exposed dowels on the side rails with the pre-
drilled holes on the Headboard (A) post.
2. Insert 6 sets of Short Allen Bolt (G) with Spring Washer (F) and Flat Washer (E) through the holes of the pre-
attached metal plate on the side rail, into the insert nut found on the Headboard (A) posts as seen
3. Tighten by Allen Key (H).
4. Repeat steps # 1 & # 2 to attach the Footboard (B) to the 2 Side Rails (C), as seen in the illustration below.

Page 4/ 6
5. Roll out the 2 Slat Roll (D) onto the slat support rail of the Side Rails (C) as seen in the illustration below.
6. Secure the slat rolls with 64 Wood Screws (I) using a Phillips Head Screwdriver (not included).
Assembly Instructions (High position):
7. The bed is assembled in the low position when shipped. If you wish to use it without the box spring, follow the
instructions below.
a. Move the extra mattress support rail found on the bottom of the side rail up by removing the Allen
Bolts and Washers that were pre installed using theAllen Key (H) by rotating counterclockwise as
seen in the illustration below.
b. Fasten the mattress support to the holes found at the top of the Side Rail (C) by aligning the bolts
with washers and rotate clockwise to tighten using theAllen Key (H).

Page 5/ 6
8. Roll out the Slat Roll (D) onto the slat support rail of the Side Rails (C) and secure the slat rolls with Wood
Screw (I) using a Phillips Head Screwdriver.
9. If the Bed doesn’t sit level, adjust the levelers underneath the legs in or out.
10. Assembly is complete.

Page 6/ 6
Note: The Headboard is designed to attach the box spring frame (sold separately). Use the hardware
supplied with the Headboard to attach the box spring frame. Pre assembled the box frame first. Make sure
the face plate of the box frame is set at high position.
1. Hold the Headboard (A) upright and tilt slightly towards the faceplates of the pre assembled bed frame.
2. Align the slots of the faceplates with the pre-drilled holes of the headboard, as seen below. If the holes do not
align perfectly, adjust the levelers underneath the legs by lifting the Headboard slightly to provide access to the
leveler. Turn the leveler until the alignment has been reach
3. Insert the Allen Bolts (G) through the Spring Washers (F), Flat Washers (E), and faceplate slots to the pre-drilled
holes of the headboard.
4. Tighten using the supplied Allen Key (H). Keep the extra hardware for future use.
5. Assembly is complete.
Care Instructions:
Dust often using a clean, soft, dry, and lint-free cloth.
Blot spills immediately and wipe with a clean, damp cloth.
We do not recommend the use of chemical cleansers, abrasives, or furniture polish on our lacquered finish.
Hardware may loosen over time. Periodically check to make sure all connections are tight. Re-tighten if
necessary.
Thank you for your purchase
Stores | catalog | www.potterybarn.com

Page 1/ 10
CLARA QUEEN AND KING BED
ASSEMBLY INSTRUCTIONS
Date: 2014-Oct.-23
Rev: 2014-Dec-12 www.potterybarn.com

Page 2/ 10
Important Safety Instructions:
Please read all instructions carefully before assembling this Bed.
For your safety, assembly by two or more adults is strongly recommended.
Keep these instructions for future use.
Use only vendor-supplied hardware to assemble this item. Using unauthorized hardware could jeopardize the
structural integrity of the item.
Pre-assembly:
Remove all parts and hardware from the box. Place all items on a carpeted or scratch-free work surface, as this
will avoid damaging parts during assembly. The shipping box provides an ideal work surface.
To avoid accidentally discarding small parts or hardware, do not dispose of any packaging or contents of the
shipping carton until assembly is complete.
Use the parts and hardware lists below to identify and separate each of the pieces included.
The illustrations provided allow for easier assembly when used in conjunction with the assembly instructions.
The use of power tools to aid in assembly is not recommended. Power tools can damage the hardware and split
the wood.
Parts Included:
A- Headboard – 1x
B- Footboard – 1x
C- Side Rail – 2x
D- Center Support Rail – 1x
E - Long Support Leg – 3x
F - Short Support Leg – 3x
G - Slat Roll – 2x

Page 3/ 10
Hardware Enclosed:
H- Flat Washer – 12x I- Spring Washer – 12x J- ShortAllen Bolt – 12x K- Long Allen Bolt – 1x
M6x25 mm
M6x150 mm
L- Allen Key – 1x M- Wood Screw – 64x
4x30 mm
Tools Required (not included):
Philips Head Screwdriver
Assembly Instruction Steps:
Note: The mattress support on the side rails is pre-assembled in the low position when shipped to allow bed to be
used with a box spring mattress. If you intend to use your bed without a box spring, an adjustable mattress support
rail will have to be raised at the higher position on side rails. Follow Step 13 and onward if you intend to use bed
without a box spring
1. Attach the 2 Side Rails (C) to the Headboard (A) by aligning the exposed dowels on the Side Rails, with the pre-
drilled holes on the posts of the Headboard.
2. Insert 6 sets of: Short Allen Bolt (J), Spring Washer (I), and Flat Washer (H) through the holes on the pre-
attached metal plate of the Side Rail, and into the insert nut on the Headboard posts as seen in the illustration
below.
3. Tighten by Allen Key (L).

Page 4/ 10
4. Repeat steps #1 - #3 to attach the Footboard (B) to the 2 Side Rails (C), as seen in the illustration below.
5. Attach the 3 Short Support Legs (F) to the Center Support Rail (D), by inserting the hanger bolts into the insert
nut found at the Center Support Rail, as seen in the illustration below.
6. Turn clockwise to tighten the Short Support Legs (F).
7. Secure/store the 3 Long Support Legs (E) to the Center Support Rail (D) and secure with a Long Allen Bolt (K),
as seen in the illustration below.
8. Use the Allen Key (L) to tighten the Long Allen Bolt (K), as seen below.