PotteryBarn hampton double door cabinet with cubbies User manual

hampton double door cabinet with cubbies
Note: For safe mounting, it is essential to use the proper to use the proper hardware for your wall
type. Contact local hardware store for assistance if necessary. For your safely and ease,
installation by two people is strongly recommended.
Note: Mount to wood studs whenever possible. Use a stud finder to locate stud in desired mounting
position. If mounting locations align with stud, use stud mounting screws. If there is no stud, toggle
screws should be used.
Caution: Contains small parts. Keep out of reach of children.
Hardware Included:
(1) french cleat
(2) stud mounting screws
(2) glass shelves
(1) small anchor, (1) small screw, (1) plastic cap
(4) shelf brackets
(18) Plastic Plugs
(2) toggle anchors and (2) toggle screws (for dry wall only)
Mounting Instructions (Dry Wall Mounting):
1) Place the template (provided) at a desired location as a guide. Use a carpenter’s level to ensure that
cabinet will be level. The two marked holes on the template will be the insertion point of your mounting
hardware.
2) Place a #2 Phillips screwdriver into recess of the toggle anchor (B). Do not “push” the anchor, it is
designed to bore into the wall like a drill bit. Slowly turn the anchor clockwise while applying pressure until
the flange just touches the wall. Keep turning clockwise until one arrow on head points to the 12 o’clock
position.
3) Place the french cleat (I) on the wall, align the end holes with the toggle anchors. Insert toggle screw (A)
through the french cleat, screw into toggle anchor turning clockwise. You will feel a slight resistance.
Continue turning screw until the screw head touches the anchors flange. Tighten screw until it becomes
difficult to turn. At this point the internal pivot will have engaged the backside of the dry wall. (see
illustration 1)
4) Align the slot at the back of cabinet over the french cleat and slide cabinet down until the slot rests on the
french cleat. (see illustration 2)
5) With a pencil, mark on the wall through the location of the lower mounting points.
6) Take away the cabinet, use the marked pint as the insertion point of the small anchor (D). Place the #2
Phillips screwdriver into recess of the anchor. Slowly turn the anchor clockwise while applying pressure
until the flange just touches the wall.
7) Again, align the slot on the back of cabinet over the french cleat and slide cabinet down until the slot rests on
the french cleat. Insert small screw © through the pre-drilled holes inside the cabinet. Tighten against
wall. Cover the screw head with plastic cap (F). (see illustration 3)
Mounting Instructions (Stud Mounting):
1) Place the frech cleat (I) at the desired location. Use a carpenter’s level to ensure that cabinet will be level.
Insert mounting screws (G) into the tow end holes of the french cleat, tighten using Phillips screwdriver or drill.
2) Follow step 4 to step 7 as above.
Shelf Installations:
Insert shelf brackets (H) into coordinating holes at desired level. Carefully place the glass shelf onto the pads
of shelf brackets (see illustration 4)
Plastic Plug Installion:
Insert plastic plugs (E) into the screw holes on the cabinet, push in with index finger. (see illustration 5)

Small Anchor Plastic plug Plastic cap Stud mounting
(D) - 1pc (E) - 18 pcs (F) - 1pc Screw (G) - 2pcs
WALL
illustration1
(A)
Hardware Included:
Shelf brackets French cleat
(H) - 4 pcs (I) - 1pc
illustration3
(F)
(D)illustration2
illustration4
(H)
(E)
4586574(R4)
* maximum load not to exceed 120lbs *
Care Instructions:
Wipe with a soft, dry cloth. To protect the finish,
Do not apply household cleaners or abrasives.
Thank you for your purchase
Toggle screw Toggles Anchor Small screw
(A) - 2pcs (B) - 2pcs (C) - 1pc
Illustration5
(E)