Power Fist 8968828 User manual

V4.0 8968828
Please read and understand allinstructionsbefore use.Retain this manualfor
futurereference.
User Manual
12 in. Electric
Concrete Saw

8968828 12 in. Electric Concrete Saw V4.0
2 For technical questions call 1-800-665-8685
SPECIFICATIONS
Theoretical Horsepower(HP) 2.5
Blade Size (in.)
12
Arbor Size (in.) 1
Cutting Depth (in.) 3-1/2
Speed Rating (RPM) 4,500
Includes Wrench,0.6mpiper,(2)blades
SAFETY
WARNING! Read and understand all instructions before using this tool. The
operator must follow basic precautions to reduce the risk of personal injury
and/or damage to the equipment.
Keep this manual for safety warnings, precautions, operating or inspection and
maintenance instructions.
HAZARD DEFINITIONS
Please familiarize yourself with the hazard notices found in this manual. A notice
is an alert that there is a possibility of property damage, injury or death if certain
instructions are not followed.
DANGER! This notice indicates an immediate and specific hazard that will
result in severe personal injury or death if the proper precautions
are not taken.
WARNING! This notice indicates a specific hazard or unsafe practice that
could result in severe personal injury or death if the proper
precautions are not taken.
CAUTION! This notice indicates a potentially hazardoussituation that may result
12 in. Electric
Concrete Saw

V4.0 12 in. Electric Concrete Saw 8968828
Visitwww.princessauto.comfor more information 3
in minor or moderate injuryif proper practices are not taken.
NOTICE! This notice indicates that a specific hazard or unsafe practice will
result in equipment or property damage, but not personal injury.
WORK AREA
•Keep work area clean and well lit. Cluttered or dark areas invite accidents.
•Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks,
which may ignite the dust or fumes.
•Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
ELECTRICALSAFETY
•Power tool plugs must match the outlet. Never modify the plug in any way.
Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock.
•Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
•Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
•Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase the risk of electric
shock.
•When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
•If operating a power tool in a damp location is unavoidable, use a ground
fault circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the
risk of electric shock.
PERSONAL SAFETY
•Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired or under

8968828 12 in. Electric Concrete Saw V4.0
4 For technical questions call 1-800-665-8685
the influence of drugs, alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
•Use personal protective equipment. Always wear eye protection. Protective
equipment such as dust mask, non-skid safety shoes, hardhat, or hearing
protection used for appropriate conditions will reduce personal injuries.
•Prevent unintentional starting. Ensure the switch is in the off-position
before connecting to power source and/or battery pack, picking up or
carrying the tool. Carrying power tools with your finger on the switch or
powering tools that have the switch on invites accidents.
•Remove any adjusting key or wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of the power tool may result
in personal injury.
•Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
•Dress properly. Do not wear loose clothing or jewelry. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewelry or long
hair can be caught in moving parts.
•If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of dust
collection can reduce dust-related hazards.
POWER TOOL USE AND CARE
•Do not force the power tool. Use the correct power tool for your application.
The correct power tool will do the job better and safer at the rate for which
it was designed.
•Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and must
be repaired.
•Disconnect the plug from the power source and/or the battery pack from
the power tool before making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
•Store idle power tools out of the reach of children and do not allow people
who are unfamiliar with the power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands of untrained users.

V4.0 12 in. Electric Concrete Saw 8968828
Visitwww.princessauto.comfor more information 5
•Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
•Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
•Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those
intended could result in a hazardous situation.
SERVICE
•Have your power tool serviced by a qualified personnel using only identical
replacement parts. This will ensure that the safety of the power tool is
maintained.
CONCRETESAW SAFETY WARNINGS
•The guard provided with the tool must be securely attached to the power
tool and positioned for maximum safety, so the least amount of wheel is
exposed towards the operator. Position yourself and bystanders away from
the plane of the rotating wheel. The guard helps to protect operator from
broken wheel fragments and accidental contact with wheel.
•Use only bonded reinforced or diamond cut-off wheels for your power tool.
Just because an accessory can be attached to your power tool, it does not
assure safe operation.
•The rated speed of the accessory must be at least equal to the maximum
speed marked on the power tool. Accessories running faster than their rated
speed can break and fly apart.
•Wheels must be used only for recommended applications. Do not grind
with the side of a cut-off wheel. Abrasive cut-off wheels are intended for
peripheral grinding and side forces applied to these wheels may cause them
to shatter.
•Always use undamaged wheel flanges that are of correct diameter for your
selected wheel. Proper wheel flanges support the wheel thus reducing the
possibility of wheel breakage.

8968828 12 in. Electric Concrete Saw V4.0
6 For technical questions call 1-800-665-8685
•Do not use worn down reinforced wheels from larger power tools. Wheels
intended for a larger power tool are not suitable for the higher speed of a
smaller tool and may burst.
IMPORTANT! The above warning does not apply to tools that are specifically
designed to be used with diamond wheels.
•The outside diameter and the thickness of your accessory must be within
the capacity rating of your power tool. Accessories sized incorrectly cannot
be adequately guarded or controlled.
•The arbor size of wheels and flanges must properly fit the spindle of the
power tool. Wheels and flanges with arbor holes that do not match the
mounting hardware of the power tool will run out of balance, vibrate
excessively and may cause loss of control.
•Do not use damaged wheels. Before each use, inspect the wheels for chips
and cracks. If power tool or wheel is dropped, inspect for damage or install
an undamaged wheel. After inspecting and installing the wheel, position
yourself and bystanders away from the plane of the rotating wheel and run
the power tool at maximum no load speed for one minute. Damaged wheels
will normally break apart during this test.
•Wear personal protective equipment. Depending on application, use face
shield, safety goggles or safety glasses. As appropriate, wear dust mask,
hearing protectors, gloves and shop apron capable of stopping small
abrasive or workpiece fragments. The eye protection must be capable of
stopping flying debris generated by various operations. The dust mask or
respirator must be capable of filtrating particles generated by your
operation. Prolonged exposure to high intensity noise may cause hearing
loss.
•Keep bystanders a safe distance away from work area. Anyone entering the
work area must wear personal protective equipment. Fragments of
workpiece or of a broken wheel may fly away and cause injury beyond
immediate area of operation.
•Hold the power tool by insulated gripping surfaces only, when performing
an operation where the cutting accessory may contact hidden wiring or its
own cord. Cutting accessory contacting a live wire may charge exposed
metal parts of the power tool and could give the operator an electric shock.

V4.0 12 in. Electric Concrete Saw 8968828
Visitwww.princessauto.comfor more information 7
•Position the cord clear of the spinning accessory. If you lose control, the
cord may be cut or snagged and your hand or arm may be pulled into the
spinning wheel.
•Never lay the power tool down until the accessory has come to a complete
stop. The spinning wheel may grab the surface and pull the power tool out
of your control.
•Do not run the power tool while carrying it at your side. Accidental contact
with the spinning accessory could snag your clothing, pulling the accessory
into your body.
•Regularly clean the power tool’s air vents. The motor’s fan will draw the
dust inside the housing and excessive accumulation of powdered metal may
cause electrical hazards.
•Do not operate the power tool near flammable materials. Sparks could
ignite these materials.
•Do not use accessories that require liquid coolants. Using water or other
liquid coolants may result in electrocution or shock.
KICKBACK AND RELATED WARNINGS
Kickback is a sudden reaction to a pinched or snagged rotating wheel. Pinching
or snagging causes rapid stalling of the rotating wheel which in turn causes the
uncontrolled power tool to be forced in the direction opposite of the wheel’s
rotation at the point of the binding.
If an abrasive wheel is snagged or pinched by the workpiece, the edge of the
wheel that is entering into the pinch point can dig into the surface of the
material causing the wheel to climb out or kick out. The wheel may either jump
toward or away from the operator, depending on direction of the wheel’s
movement at the point of pinching. Abrasive wheels may also break under these
conditions.
Kickback is the result of power tool misuse and/or incorrect operating
procedures or conditions and can be avoided by taking proper precautions as
given below.
•Maintain a firm grip on the power tool and position your body and arm to
allow you to resist kickback forces. Always use auxiliary handle, if provided,
for maximum control over kickback or torque reaction during start-up. The

8968828 12 in. Electric Concrete Saw V4.0
8 For technical questions call 1-800-665-8685
operator can control torque reactions or kickback forces, if proper
precautions are taken.
•Never place your hand near the rotating accessory. Accessory may kickback
over your hand.
•Do not position your body in line with the rotating wheel. Kickback will
propel the tool in direction opposite to the wheel’s movement at the point of
snagging.
•Use special care when working corners, sharp edges etc. Avoid bouncing
and snagging the accessory. Corners, sharp edges or bouncing have a
tendency to snag the rotating accessory and cause loss of control or
kickback.
•Do not attach a saw chain, woodcarving blade, segmented diamond wheel
with a peripheral gap greater than 10 mm or toothed saw blade. Such
blades create frequent kickback and loss of control.
•Do not apply excessive pressure on the wheel. Do not attempt to make an
excessive depth of cut. Overstressing the wheel increases the loading and
susceptibility to twisting or binding of the wheel in the cut and the
possibility of kickback or wheel breakage.
•When wheel is binding or when interrupting a cut for any reason, switch off
the power tool and hold the power tool motionless until the wheel comes to
a complete stop. Never attempt to remove the wheel from the cut while the
wheel is in motion otherwise kickback may occur. Investigate and take
corrective action to eliminate the cause of wheel binding.
•Do not restart the cutting operation in the workpiece. Let the wheel reach
full speed and carefully re-enter the cut. The wheel may bind, walk up or
kickback if the power tool is restarted in the workpiece.
•Support panels or any oversized workpiece to minimize the risk of wheel
pinching and kickback. Large workpieces tend to sag under their own
weight. Supports must be placed under the workpiece near the line of cut
and near the edge of the workpiece on both sides of the wheel.
•Use extra caution when making a pocket cut into existing walls or other
blind areas. The protruding wheel may cut gas or water pipes, electrical
wiring or objects that can cause kickback.

V4.0 12 in. Electric Concrete Saw 8968828
Visitwww.princessauto.comfor more information 9
UNPACKING
WARNING! Do not operate the tool if any part is missing. Replace the
missing part before operating. Failure to do so could result in a malfunction
and personal injury.
Remove the parts and accessories from the packaging and inspect for damage.
IDENTIFICATION KEY
1. Motor Casing
2. Back Cover
3. Carbon Brush Cover
4. Handle
5. Switch
6. Auxiliary Handle
7. Cover
8. Flange
9. Wheel
10. Saw Blade
OPERATINGINSTRUCTIONS
INSTALLING/REMOVINGA DISC
WARNING! Always disconnect the machine
from the power supply before attempting to
install or remove a cutting disc.
NOTICE! Ensure that the machines arbor and
the blade flanges are clean and free from
dust and debris. Ensure that the direction of
rotation marked on the blade matches the
direction of rotation marked on the
machine’s guard. The arbor bolt has a left
hand thread

8968828 12 in. Electric Concrete Saw V4.0
10 For technical questions call 1-800-665-8685
1. Turn counter clockwise to tighten the
arbor bolt.
2. Turn clockwise to loosen the arbor bolt.
3. To remove a cutting disc, reverse the
above installation procedure.
INSTALLING A DUST EXTRACTION MACHINE
WARNING! Dust can be dangerous. It is strongly recommend to use a
suitable dust extraction machine (not supplied) to keep the workplace as
clean and safe as possible.
The suction hose from the dust extraction machine should be attached to dust
extraction port of the saw.
1. Remove the rubber cap from the dust
extraction port and store it when not in use.
2. Push the connection hose from the dust
extraction machine into the dust extraction
port of the saw (Fig. 4)
3. Follow all instructions supplied with the
dust extraction machine.
4. Ensure that the hose and power cable of any
attached dust extraction machine do not
pose tripping (or any other) hazards to the
operator.
5. When the dust extraction machine is no longer required, remove it from the
saw and replace the cap to the dust extraction port.
ON/OFF TRIGGER SWITCH
This machine is equipped with a safety-start trigger switch. To start the tool:

V4.0 12 in. Electric Concrete Saw 8968828
Visitwww.princessauto.comfor more information 11
1. Push in the safety lock button (Fig.5a) on
the side of the handle with your thumb.
2. Depress the main trigger switch (Fig.5b) to
start the motor.
WARNING! Never start the saw with the cutting
edge of the saw blade in contact with the
workpiece surface.
PRE-CUTTING
•Ensure that the power supply matches the
requirements specified on the matches the
requirements specified on the machines rating plate.
•Ensure that the machine trigger switch is in the OFF position. If the machine
is connected to a power source with trigger switch the ON position, the
machine could start operating immediately with the possibility of a serious
accident occurring.
•If an extension cable is required, it must be a suitable type for use outdoors
and so labeled.
•The manufacturer’s instructions should be followed when using an
extension cable.
•Route any extension cable so that it does not pose a tripping (or any other)
hazard to the operator or any bystanders.
WHEEL GUARD ADJUSTMENT
The wheel guard is adjustable and should be
positioned to provide the operator with personal
protection and maximum visibility of the cutting
area.
1. Loosen the wheel guard locking knob and
rotate the guard to the required position.
(Fig. 6)
2. Securely tighten the wheel guard locking
knob to lock the guard in place.
NOTICE! Check regularly the tightness of this
locking knob and the security of the wheel guard during operation.

8968828 12 in. Electric Concrete Saw V4.0
12 For technical questions call 1-800-665-8685
PARTS BREAKDOWN

V4.0 12 in. Electric Concrete Saw 8968828
Visitwww.princessauto.comfor more information 13
PARTS LIST
#
DESCRIPTION
QTY
1 Cable Wire 1
2 M6Nut 1
3 Left Handle 1
4
M5x20 Screw
2
5
Cable Sheath
1
6 Tension 1
7 Wiring Buckle 2
8
Switch
1
9 Right Handle 1
10 Φ6 Washer 1
11 M6x25 Screw 1
12
ST4x15 Screw
8
13 ST5x24 Screw 4
14 MotorEnd Cover 1
15 ST4x15 Screw 2
16
Soft Starter
1
17 MotorHousing 1
18 609 RSBearing 1
19 Stator 1
20 ST5x80 Screw 2
21 Spring 2
22 Brush Holder 2
23 ST4x10 Screw 2
24
Brush
2
25 Brush Cover 2
26 ST3x8 Screw 2
27 Rotor 1
28 Baffle 1
29
Bearing Washer
1
30 6202 RSBearing 1
31
Gear31 Box
1
32 M4x10 Screw 1
33 ST5x40 Screw 4
34 6200 RSBearing 1
35
M4x10 Screw
2
36 Gear 1
37 GearWasher 1
38 Bearing PressurePlate 1
39
M4x10 Screw
2
40 Oil Baffle 40 1
41 Gear41 1
42 M8 Nut 1
43 Oil Baffle 43 1
44 GearBox 1
45 M5x25 Screw 4
46 Handle 1
47
M6x45 Screw
4
48 4x4x14Key 1
49 Drive Shaft 1
50 3x3x14Key 1
51 6301RSBearing 2
52
Gear
1
53 Left M8 Nut 1
54 Breakwater 1
55
Φ12 Spring Washer
1
56 M12x15Screw 1
57 Fixed Plate 1
58 M6x16 Screw 4
59
LockPin
1

8968828 12 in. Electric Concrete Saw V4.0
14 For technical questions call 1-800-665-8685
60
LockPin Spring
1
61 Circlip forShaft 6 1
62 GearBox 1
63 6200Z Bearing 1
64
Oil Baffle
1
65 Circlip forShaft 15 1
66 Axle Sleeve 1
67 BevelGear 1
68 GearCover 1
69
Φ
60x1.5O-Ring 1
70 M6x16 Screw 4
71 LockingHand Wheel 1
72
M8x24 Square Bolt
1
73 M5x10 Screw 2
74 Outlet 1
75 M5x10 Screw 6
76 Right Dust Outlet 1
77
Guard
1
78 Left Dust Outlet 1
79 M4x30 Screw 1
80
M4x10 Screw
1
81 Dust OutletCover 1
82 Outlet 1
83 6302ZBearing 1
84
4x4x30Key
1
85
Spindle
1
86 Bearing PressurePlate 1
87 M6x16 Screw 3
88 DustproofRing 1
89
Flange
1
90 Saw Blade 1
91 Flange 1
92 Washer 1
93 Screw 1
94 PVC Water Pipe 6x8
(230 mm) 1
95
PVC Water Pipe 6x8
(600 mm) 1
96
Tap
1
97 BreakwaterPlate 1
98 M5x10 Screw 2
99 35 Bolt 2
100
Wheel
2
101
M8 Lock Nut
2
102 Pump 1
103 PVC Water Pipe 6x8 1
104
Φ
22.2 SawBlade
Pressure Plate
1
105 Dust Casing 1
106 #16 Wrench 1
107 Gasket 1 mm 1

V4.0 12 in. Electric Concrete Saw 8968828
Visitwww.princessauto.comfor more information 15

8968828 12 in. Electric Concrete Saw V4.0
16 For technical questions call 1-800-665-8685

V 4,0 8968828
Vous devez lire et comprendretoutes les instructionsavant d'utiliserl'appareil.
Conservezce manuel afinde pouvoirle consulterplustard.
Manuel d'utilisateur
Scie à béton électrique,
12 po

8968828 Scie à béton électrique,12 po V 4,0
2 En cas de questionstechniques,appelez le 1-800-665-8685
SPÉCIFICATIONS
Puissance théorique (CV) 2,5
Taille de lame (po)
12
Taille d’arbre (po) 1
Profondeurde coupe(po) 3 1/2
Vitesse nominale (tr/min) 4 500
Comprend Clé, fil de 0,6 m,(2) lames
SÉCURITÉ
AVERTISSEMENT ! Veuillez lire et comprendre toutes les instructions avant
d'utiliser cet outil. L'utilisateur doit respecter les précautions de base
lorsqu'il utilise cet outil afin de réduirele risque de blessure ou de
dommage à l'équipement.
Conservez ce manuel qui contient les avertissements de sécurité, les
précautions, les instructions de fonctionnement ou d'inspection et d'entretien.
DÉFINITIONSDE DANGER
Veuillez-vous familiariser avec les avis de danger qui sont présentés dans ce
manuel. Un avis est une alerte indiquant qu'il existe un risque de dommage à la
propriété, de blessure ou de décès si on ne respecte pas certaines instructions.
DANGER ! Cet avis indique un risque immédiat et particulier qui
entraînera des blessures corporelles graves ou même la
mort si on omet de prendre les précautions nécessaires.
AVERTISSEMENT ! Cet avis indique un risque particulier ou une pratique non
sécuritaire qui pourrait entraîner des blessures
corporelles graves ou même la mort si on omet de
Scie à béton électrique,
12 po

V 4,0 Scie à béton électrique,12 po 8968828
Visitez www.princessauto.com pour plus d'informations 3
prendre les précautions nécessaires.
ATTENTION ! Cet avis indique une situation possiblement dangereuse qui
peut entraîner des blessures mineures ou modérées si on
ne procède pas de la façon recommandée.
AVIS ! Cet avis indique un risque particulierouune pratiquenon
sécuritairequi entraînera des dommages au niveau de
l'équipement ou desbiens, maisnon des blessures corporelles.
AIRE DE TRAVAIL
•Gardez l’aire de travail propre et bien éclairée. Les aires encombrées ou
sombres favorisent les accidents.
•N’utilisez pas d’outils électriques dans des environnements explosifs tels
qu’en présence de liquides, de gaz ou de poussières inflammables. Les
outils électriques créent des étincelles qui peuvent enflammer la poussière
ou les vapeurs.
•Gardez les enfants et les gens à proximité loin pendant l’utilisation d’un outil
électrique. Les distractions peuvent causer une perte de contrôle.
SÉCURITÉEN ÉLECTRICITÉ
•La fiche mâle de l’outil électrique doit correspondre à la prise. Ne modifiez
jamais la fiche. N’utilisez jamais de fiche d’adaptation avec des outils
électriques mis à la terre (masse). Les fiches non modifiées et les prises
correspondantes réduisent le risque de décharge électrique.
•Évitez tout contact corporel avec des surfaces mises à la terre comme les
tuyaux, les radiateurs, les cuisinières et les réfrigérateurs. Le risque de
décharge électrique augmente si votre corps est mis à la terre ou à la
masse.
•N’exposez pas les outils électriques à la pluie ou aux liquides. De l’eau qui
s’infiltre dans un outil électrique augmente le risque de décharge électrique.
•N’utilisez pas le cordon de manière abusive. N’utilisez jamais le cordon pour
porter, tirer ou débrancher l’outil électrique. Tenez le cordon à l’écart de la
chaleur, de l’huile, des bords coupants ou des pièces mobiles. Les cordons
endommagés ou entortillés augmentent le risque de décharge électrique.

8968828 Scie à béton électrique,12 po V 4,0
4 En cas de questionstechniques,appelez le 1-800-665-8685
•Si vous utilisez un outil électrique à l’extérieur, utilisez une rallonge
approuvée pour un usage extérieur. L’utilisation d’un cordon conçu pour un
usage extérieur réduit le risque de décharge électrique.
•Si vous devez absolument utiliser un outil électrique dans un endroit très
humide, utilisez un équipement protégé par un dispositif à disjoncteur
différentiel de fuite à la terre (DDFT). L’utilisation d’un DDFT réduit le risque
de décharge électrique.
SÉCURITÉPERSONNELLE
•Restez alerte, gardez les yeux sur le travail et faites preuve de bon sens
lorsque vous utilisez un outil électrique. N’utilisez pas un outil électrique si
vous êtes fatigué ou sous l’effet de drogues, d’alcool ou de médicaments.
Un instant d’inattention lors de l’utilisation d’un outil électrique peut
provoquer des blessures corporelles graves.
•Utilisez un équipement de protection individuelle. Portez toujours une
protection des yeux. Un équipement de protection, notamment un masque
antipoussières, des bottes de sécurité antidérapantes, un casque de
protection et une protection de l’ouïe, utilisé dans des conditions
appropriées, réduira les blessures corporelles.
•Évitez le démarrage non intentionnel. Assurez-vous que l’interrupteur
d’alimentation est à la position OFF (arrêt) avant de brancher l’outil à une
source d’alimentation ou à un bloc-pile ou avant de ramasser ou de
transporter l’outil. Des accidents risquent de se produire si vous transportez
les outils électriques avec un doigt sur l’interrupteur ou si vous branchez
l’outil avec l’interrupteur en marche.
•Enlevez les clés de réglage ou de serrage avant de mettre l’outil électrique
en marche. Une clé ou une clavette laissée en place sur une pièce rotative
de l’outil électrique peut entraîner des blessures corporelles.
•N’opérez pas l’outil si vous devez étirer les bras pour le faire. Restez stable
et en équilibre à tout moment. Cela permet d’avoir un meilleur contrôle de
l’outil électrique en cas de situations inattendues.
•Portez des vêtements appropriés. Ne portez ni vêtements amples ni bijoux.
N’approchez ni les cheveux, ni les vêtements, ni les gants des pièces
mobiles. Les vêtements amples, les bijoux et les cheveux longs risquent
d’être coincés dans des pièces mobiles.