Power Fist 9095746 User manual

V1.0 9095746
Please read and understand all instructions before use. Retain this manual for
future reference.

9095746 20V Li-Ion Cordless Brushless Compact Band Saw V1.0
2 For technical questions call 1-800-665-8685
SPECIFICATIONS
Voltage Rating (V DC) 20V DC
Cutting Capacity (in.) 2-1/2 in.
Blade Speed(s) (ft/min) 0 to 630 ft/min
Blade Size (in.) 33 x 1/2 in. (835 x 13 x 0.5 mm)
Battery Type Sold separately
Charger Sold separately
Material Steel/aluminum/copper/plastic
Dimensions 19 x 9-1/4 x 10-5/8 in.
HAZARD DEFINITIONS
Please familiarize yourself with the hazard notices found in this manual. A
notice is an alert that there is a possibility of property damage, injury or death
if certain instructions are not followed.
DANGER! This notice indicates an immediate and specific hazard that will
result in severe personal injury or death if the proper
precautions are not taken.
WARNING! This notice indicates a specific hazard or unsafe practice that
could result in severe personal injury or death if the proper
precautions are not taken.
CAUTION! This notice indicates a potentially hazardous situation that may
result in minor or moderate injury if proper practices are
not taken.
NOTICE! This notice indicates that a specific hazard or unsafe practice will
result in equipment or property damage, but not personal injury.

V1.0 20V Li-Ion Cordless Brushless Compact Band Saw 9095746
Visit www.princessauto.com for more information 3
INTRODUCTION
The Compact Band Saw is designed to cut a variety of materials including steel,
aluminum, copper or plastic. The tool requires the Powerfist 20V cordless
system Li-ion battery and charger (sold separately).
SAFETY
WARNING! Read and understand all instructions before using this tool. The
operator must follow basic precautions to reduce the risk of personal injury
and/or damage to the equipment.
Keep this manual for safety warnings, precautions, operating or inspection and
maintenance instructions.
WORK AREA
1. Operate in a safe work environment. Keep your work area clean, well-lit
and free of distractions. Place lights so you are not working in a shadow.
2. Keep anyone not wearing the appropriate safety equipment away from
the work area.
3. Store unused tools properly in a safe and dry location to prevent rust or
damage. Lock tools away and keep out of the reach of children.
4. Do not install or use in the presence of flammable gases, dust or liquids.
PERSONAL SAFETY
WARNING! Wear personal protective equipment approved by the Canadian
Standards Association (CSA) or American National Standards Institute
(ANSI).
PERSONAL PROTECTIVE EQUIPMENT
1. Always wear impact safety goggles that provide front and side protection
for the eyes. Eye protection equipment should comply with CSA Z94.3-07
or ANSI Z87.1 standards based on the type of work performed.
2. Wear the appropriate type of full-face shield in addition to safety googles,
as the work can create chips, abrasive or particulate matter.
3. Wear gloves that provide protection based on the work materials or to
reduce the effects of tool vibration.
a. Do not wear gloves when operating a tool that can snag the material
and pull the hand into the tool.

9095746 20V Li-Ion Cordless Brushless Compact Band Saw V1.0
4 For technical questions call 1-800-665-8685
4. Wear protective clothing designed for the work environment and tool.
5. Non-skid footwear is recommended to maintain footing and balance in the
work environment.
6. Wear steel toe footwear or steel toe caps to prevent a foot injury from
falling objects.
7. Wear the appropriate rated dust mask or respirator.
8. This tool can cause hearing damage. Wear hearing protection gear with an
appropriate Noise Reduction Rating to withstand the decibel levels.
PERSONAL PRECAUTIONS
Control the tool, personal movement and the work environment to avoid
personal injury or damage to tool.
1. Do not operate any tool when tired or under the influence of drugs,
alcohol or medications.
2. Avoid wearing clothes or jewelry that can become entangled with the
moving parts of a tool. Keep long hair covered or bound.
3. Do not overreach when operating a tool. Proper footing and balance
enables better control in unexpected situations.
4. Support the workpiece or clamp it to a stable platform. Holding the
workpiece by hand or against your body may lead to personal injury.
5. Securely hold this tool using both hands. Using a tool with only one hand
can result in loss of control.
SPECIFIC SAFETY PRECAUTIONS
DANGER! When the tool is in operation, keep hands away from the saw
blade and the area it is being applied to. Failure to follow this warning will
result in amputation, serious personal injury or death.
WARNING! DO NOT let comfort or familiarity with product (gained from
repeated use) replace strict adherence to the tool safety rules. If you use
this tool unsafely or incorrectly, you can suffer serious personal injury.
WARNING! Some surfaces contain materials which can be toxic. When
working on materials that may contain lead, asbestos, copper chromium
arsenate or other toxic materials, extra care should be taken to avoid
inhalation and minimize skin contact.

V1.0 20V Li-Ion Cordless Brushless Compact Band Saw 9095746
Visit www.princessauto.com for more information 5
1. Use the correct tool for the job. This tool was designed for a specific
function. Do not modify or alter this tool or use it for an
unintended purpose.
2. Do not use the tool if any parts are damage broken or misplaced.
Repair or replace the parts.
3. Only use accessories that are specifically designed for use with the
tool. Ensure the accessory is tightly installed.
4. Do not use a dull or damaged cutting accessory. A dull cutting accessory
requires more force to use the tool, possibly causing the accessory to
break. This may cause an injury and will damage the workpiece.
a. Dull or improperly set cutting accessories produce a narrow kerf
that can cause excessive friction on the cutting accessory,
resulting in binding or a kickback. Keep the cutting accessory’s
edge sharp and clean.
5. Use the correct mounting hardware. The mounting hardware is
designed to hold the cutting accessory on the tool to allow optimum
performance and safety of operation. Mismatched mounting hardware
may result in a tool malfunction and cause an injury.
a. Always use blades that are correctly sized and shaped for the
tool. Blades that do not match the tool’s mounting hardware will
run erratically, causing loss of control.
6. Check the cutting accessory for damage before each use. A damaged
accessory can break during use and cause serious injury.
7. Inspect material for foreign objects such as debris. Remove from
material before cutting.
8. Affix the workpiece to a stable platform to prevent movement,
minimize body exposure to injury, cutting accessory binding or loss of
control.
9. Position the tool on the larger section of a supported workpiece to
complete a cut. Cut the small portion away from the larger portion.
Support the smaller portion, if possible, to prevent it from binding
when the cut is almost complete.
10. Never confine the part of the workpiece being cut away by holding,
clamping or using length stops against it. That part of the workpiece could

9095746 20V Li-Ion Cordless Brushless Compact Band Saw V1.0
6 For technical questions call 1-800-665-8685
become wedged against the blade and be thrown violently. The cut away
part of the workpiece must be free to move sideways
11. Always handle the band saw blade with care when mounting or removing it.
12. Ensure the tension handle is tightened (making the blade taut) before
each use.
POWER TOOL PRECAUTIONS
1. Do not use any power tool with a malfunctioning power switch or control.
A power tool that fails to respond to the controls is dangerous and can
cause an injury. A qualified technician must repair and verify the power
tool is operating correctly, before it can be used.
2. Do not cover the air vents. Proper cooling is necessary prevent damage to
the tool’s motor.
3. Avoid unintentional starts. Ensure the switch is off when connecting to
the power source. Make sure the safety lock is set.
4. Disconnect the power source before installing or servicing the tool.
5. Remove adjusting keys and wrenches before using the tool. The tool may
eject an attached wrench or a key and cause an injury to you or a bystander.
6. Never point the tool towards yourself. It could inflict an injury.
7. Never force the tool. Excessive pressure could break the tool, resulting in
damage to your workpiece or serious personal injury. Excessive pressure
is the cause if your tool runs smoothly under no load, but roughly under
load.
8. Keep hands and fingers away from the work area. Any part of the body
contacting the tool’s working parts could result in an injury.
9. Only use an accessory that exceeds the Speed Rating (see Specifications).
10. Before using the tool on a workpiece, test the tool by running it at the
highest Speed Rating for at least 30 seconds in a safe position. Stop
immediately if there is any abnormal vibration or wobbling. Check the tool
to determine the cause.
a. Do not allow the tool to run without load for an extended period of
time, as this will shorten its life.
11. Never touch the tool accessory or workpiece during or immediately after
use. They may be hot and could inflict a burn injury.

V1.0 20V Li-Ion Cordless Brushless Compact Band Saw 9095746
Visit www.princessauto.com for more information 7
12. Take work breaks to prevent the tool's motor from overheating
and/or overloading.
13. Never use a tool with a cracked or worn tool accessory. Change the tool
accessory before using it.
14. Do not start the tool when the tool’s accessory is touching the workpiece.
KICKBACK PRECAUTIONS
Kickback is a sudden reaction to a pinched or snagged cutting accessory. The
tool kicks out and away from the workpiece while the cutting accessory is still
active. This can inflict a serious injury on the user or a bystander. Kickback can
also damage the tool or workpiece.
Kickback can be avoided by taking proper precautions:
1. Maintain a firm grip on the tool and position your body and arms to allow
you to resist a kickback. Kickback will propel the tool in the direction
opposite to the cutting accessory’s teeth or direction of rotation. A
snagged cutting accessory may pull the tool out of the grasp of the user.
2. If kickback occurs:
a. The cutting accessory may pass over a body part, causing a
seriously injury.
b. The tool may strike bystanders.
3. Use clamps or a vice to hold down smaller workpieces.
4. Use special care when working on corners, sharp edges or flexible
material. These workpieces have a tendency to snag the cutting accessory.
5. When the blade is the binding, or when interrupting a cut for any reason,
release the trigger and hold the saw motionless in the material until the
blade comes to a complete stop. Never attempt to remove the saw from
the workpiece or pull the saw backward while the blade is in motion as
kickback may occur. Investigate and take corrective actions to eliminate
the cause of blade binding.
6. When restarting a saw in the workpiece, center the saw blade in the
kerf and check that saw teeth are not engaged into the material. If saw
blade is binding, it may walk up or kickback from the workpiece as the
saw is restarted.

9095746 20V Li-Ion Cordless Brushless Compact Band Saw V1.0
8 For technical questions call 1-800-665-8685
7. Support large panels to minimize the risk of blade pinching and kickback.
Large panels tend to sag under their own weight. Supports must be placed
under the panel on both sides, near the line of cut and near the edge of
the panel.
ELECTRICAL SAFETY
WARNING! Do not touch or handle a live tool with any part of your body
that is wet or damp. Wet skin reduces resistance to electrical current,
increasing the danger of a serious or fatal shock.
1. Do not alter any parts of the tool or accessories. All parts and accessories
are designed with built-in safety features that may be compromised if
altered.
2. Protect yourself against electric shocks when working on electrical
equipment. Avoid body contact with grounded surfaces. There is an
increased chance of electrical shock if your body is grounded.
3. Do not expose the saw to rain, snow, frost or any other damp or wet
conditions. Water entering a tool will increase the risk of electric shock.
4. Hold the tool by the insulated gripping surfaces when performing an
operation where the cutting accessory may contact hidden wiring. Contact
with a live wire will also make exposed metal parts of the power tool live
and shock the operator.
BATTERY SAFETY
WARNING! Only charge a battery with a charger designed for that purpose.
Do not use modified chargers or a charger that does not specify the
voltage, amperage or recharge rate. Improper charging can lead to battery
rupturing.
WARNING! Do not charge a damaged or frozen battery. Contact your local
municipality for proper disposal procedures. Consult the Safety Data
Sheet (SDS) for your battery before use or maintenance.
1. Do not expose the battery to heat or throw it in a fire. The contents are
flammable and the battery may explode. Remove any source of ignition
such as an open flame or a tool like a heater from the area.
2. Do not inhale smoke issuing from a burning battery, as it is toxic.
3. Do not disassemble or crush the battery as the contents are corrosive
and flammable. Exposure may cause an injury. There is a risk of

V1.0 20V Li-Ion Cordless Brushless Compact Band Saw 9095746
Visit www.princessauto.com for more information 9
escaping hazardous vapors. These vapors can irritate the respiratory
track. Always ensure proper ventilation and immediately consult a
doctor, if you feel unwell.
4. Even a discharged battery may still carry a charge. To prevent a shock,
place battery terminal caps or covers over the terminal to prevent
accidental contact. Hold the battery by the bottom if moving the battery
to a different location.
5. Do not store the battery in containers / spaces with loose metal
objects. Keep it away from other metal objects that can make a
connection between terminals. Shorting out the battery terminals may
cause burns or a fire.
6. A battery-operated tool with internal batteries or with a separate battery
pack must only be powered by the included battery. Do not mix different
brands of tools and batteries or use adapters to allow you to use a battery
pack with a different voltage. This can damage the tool’s electrical
mechanism and create a fire hazard.
7. If fluids leak from the battery, avoid contact. Leaking battery fluid can
cause irritation of the skin or burns. If contact should occur, flush
immediately with water. In case of accidental contact with the eyes, seek
medical aid.
8. Do not disconnect from the power source in place of using the ON/OFF
switch on the tool. This can lead to an accidental startup when the tool is
connected to the power supply.
9. Do not allow a rechargeable battery to fully discharge. This will damage
the battery. Recharge the battery as soon as possible.
10. Do not store the battery completely discharged. Charge it fully before
storing. Recharge occasionally if storing for a long time.
CHARGER PRECAUTIONS
WARNING! Voltage is present at the charging terminals, do not probe with
conductive objects. Electric shock or electrocution may result. A battery
short can cause a large current flow, overheating, possible burns and even
a breakdown of the tool.
Before using the charger, read all instructions and cautionary markings on the
charger, battery pack and the product using the battery pack.
1. Only use the included battery charger to recharge the battery. Other

9095746 20V Li-Ion Cordless Brushless Compact Band Saw V1.0
10 For technical questions call 1-800-665-8685
chargers may be unsafe, causing an electrical short circuit or fire.
2. Disconnect the charger from its power source before attaching or
removing batteries or battery clamps.
3. Charge the battery in a well-ventilated area and never obstruct the vents
in the top and bottom of the charger. Place the charger on a flat
nonflammable surface and away from flammable materials when re-
charging the battery.
4. Do not place any object on top of the charger or place the charger on a
soft surface that may result in excessive internal heat. Place the charger in
a position away from any heat source.
5. Charge the battery at rates recommended by the battery manufacturer.
6. Do not insert the battery into the charger backwards. Make sure the
polarity symbols on the battery lines up with the polarity symbols of the
charger. A battery inserted backwards may explode causing fire and/or
injury.
7. Do not use the charger with an extension cord. This can cause a low
voltage outage during charging.
8. Do not charge leaking batteries. A compromised casing will release volatile
chemicals and gases. Charging a leaking battery can cause a fire or
explosion.
9. Do not operate the charger if it has received a sharp blow, been dropped
or otherwise damaged in any way. Have it serviced or replaced.
VIBRATION PRECAUTIONS
1. This tool vibrates during use. Repeated or long-term exposure to vibration
may cause temporary or permanent physical injury. Take frequent breaks
when using the tool.
2. If you feel any medical symptoms related to vibrations (such as tingling,
numbness, and white or blue fingers), seek medical attention as soon as
possible.
3. Wear suitable gloves to reduce the effects of vibration.
4. DO NOT use this tool before consulting a physician if one of the following
applies:
a. Pregnant b. Impaired blood circulation to

V1.0 20V Li-Ion Cordless Brushless Compact Band Saw 9095746
Visit www.princessauto.com for more information 11
the hands
c. Past hand injuries
d. Nervous system disorders
e. Diabetes
f. Raynaud's Disease
UNPACKING
WARNING! Do not operate the tool if any part is missing. Replace the
missing part before operating. Failure to do so could result in a malfunction
and personal injury.
Remove the parts and accessories from the packaging and inspect for damage.
Make sure that all items in the contents are included.
Contents:
• Compact Band Saw
• Blade
• (2) Wrenches
IDENTIFICATION KEY
A Tension Handle
B Speed Dial Wheel
C Safety Lock
D Battery Port
E Trigger
F Guide Plate
G LED
H Auxiliary Handle
Fig. 1

9095746 20V Li-Ion Cordless Brushless Compact Band Saw V1.0
12 For technical questions call 1-800-665-8685
ASSEMBLY & INSTALLATION
Letter references in parenthesis (A) refer to the included Identification Key.
BLADE INSTALLATION
WARNING! Do not use a stationary band saw blade for the portable band
saw. The stationary band saw blade is a different thickness and will not fit
the precision blade guides on the portable band saw.
CAUTION! Wear gloves when handling the saw blade during installation or
removal to avoid cuts from the blade’s teeth.
1. Remove the battery from the port (D).
2. Use band saw blades of the correction dimension (see Specifications).
3. Select a blade that will allow at least two teeth to engage the material.
a. Harder materials require finer blade teeth, while thicker or coarse
materials require coarser blade teeth.
b. Hi-speed steel blades stay sharp longer than alloy steel blades.
4. Turn the tension handle (A) clockwise to release the blade tension.
5. Turn the band saw over so the rear side is facing up.
6. Remove the old blade if replacing it.
7. Note the direction arrows on the wheels. Install the saw blade so the teeth
point to the left side (clockwise) when passing through the guide bearings.
8. Set the blade between both guide bearings, ensuring the blade is centered
on each. Hold the blade on the guides and push in to seat it.
9. Wrap the blade around the wheels. Ensure it is a proper fit and the blade
does not twist.
10. Reinstall the blade cover. Make sure the blade cover locks are set.
11. Tighten the tension handle (A) to secure the blade in place.

V1.0 20V Li-Ion Cordless Brushless Compact Band Saw 9095746
Visit www.princessauto.com for more information 13
GUIDE BAR ASSEMBLY
1. Attach the guide bar to the band saw before
operation (Fig. 2-2).
2. Release the screws on the frame (Fig. 2-1).
3. Install the guide bar with the opening around
the blade. Adjust the guide bar distance as
desired.
4. Tighten the screws to lock the guide in place.
INSTALL EXTERNAL BATTERY PACK
WARNING! Avoid unintentional starts by ensuring the safety lock (C) is
engaged before installing the battery pack.
1. Check the battery power level before each use.
a. The battery is not fully charged out of the carton. Charge the battery
before first use.
2. Install the battery by aligning the rib on the battery with the groove on
the battery port (D) and push forward until the latch clicks.
3. Remove the battery by pushing the battery lock button and pulling the
battery free.
OPERATION
TO START AND STOP SAW
NOTICE! Do not change the saw speed during a cut. Remove the saw from
the material before adjusting the speed to avoid damaging the tool.
1. Clamp the material to be cut in a vise or other clamping device. Never
attempt to use this tool by resting it on a work surface and bringing the
material to the tool. Always securely clamp the workpiece and bring the
tool to the workpiece, securely holding the tool with two hands
a. Support end pieces that are heavy enough to cause injury when they
drop after cutting.
2. Adjust the guide bar to the workpiece by loosening the screws (Fig. 2-1)
and sliding the guide bar forwards or backwards. Do not allow the guide
bar to touch the blade. Tighten the screws to secure the guide bar.
Fig. 2

9095746 20V Li-Ion Cordless Brushless Compact Band Saw V1.0
14 For technical questions call 1-800-665-8685
3. Grip the band saw by the auxiliary handle (H) and handle before starting
the tool.
4. Ensure that a minimum of two sawblade teeth will remain in the material
during the cut to keep the blade straight and prevent kickback.
5. Adjust the blade speed by turning the speed dial (B).
6. Squeeze the trigger (E).
7. Allow the band saw to reach full speed before starting the cut.
8. Tilt the unit so that the blade is vertical. To start a cut, use minimal force
to start a groove. Once the groove is started, allow the rest of the blade to
cut into the workpiece. Doing this will prevent the blade from moving
from side-to-side during cutting. The tool’s own weight provides the most
efficient downward cutting pressure.
9. Carefully avoid bringing the band saw blade suddenly and heavily into
contact with the upper surface of the workpiece. This will cause serious
damage to the band saw blade. To obtain maximum service life of the
band saw blade, ensure there is no sudden impact at the beginning of the
cutting operation.
10. Hold the saw firmly in both hands so that the saw does not fall against the
clamped or supported material when the cut is completed.
11. Release the trigger to stop the saw.
NOTICE! If the band saw becomes locked or jammed in the workpiece
material during cutting, release the trigger immediately to avoid damage to
the band saw blade and motor.
LUBRICATING SAW BLADE
DANGER! Ensure the tool is stable and take precautions when applying wax
to the moving blade to avoid amputation or serious injury.
WARNING! Never use liquid coolant with your band saw. Liquid coolants
increase the risk of electric shock. It may also damage the blade guide
bearing or the rubber on the pulleys.
Lubrication is recommended when cutting aluminum and thick materials. Cast
iron should be cut dry. Choose a cutting or lubricating wax that is designed for
a band saw and comes in a stick applicator. Apply the wax to both sides of the
blade while the saw is running. Reapply wax intermittently as needed.

V1.0 20V Li-Ion Cordless Brushless Compact Band Saw 9095746
Visit www.princessauto.com for more information 15
After prolonged cutting, the wax will cling to the pulleys of your portable
band saw. This does not affect the operation of the machine. All that is
necessary is to disconnect the machine from the power source and wipe the
wax from the pulleys.
CARE & MAINTENANCE
1. Maintain the tool with care. A tool in good condition is efficient, easier to
control and will have fewer problems.
2. Inspect the tool components periodically. Repair or replace damaged or
worn components. Only use identical replacement parts when servicing.
3. Follow instructions for lubricating and changing accessories.
4. Only use accessories intended for use with this tool.
5. Keep the tool clean, dry and free from oil/grease at all times.
6. Maintain the tool’s labels and name plates. These carry important
information. If unreadable or missing, contact Princess Auto Ltd.
for replacements.
WARNING! Only qualified service personnel should repair the tool. An
improperly repaired tool may present a hazard to the user and/or others.
CLEANING
1. Remove all swarf from the machine with a vacuum cleaner or compressed
air. Focus on removing dust from the motor’s fan vents.
2. Thoroughly clean all surfaces.
STORAGE
When not in use for an extended period, apply a thin coat of lubricant to the
steel parts to avoid rust. Remove the lubricant before using the tool again.
1. Components should be kept dry, with machined surfaces lightly oiled.
2. Always remove the saw blade and store in a safe place.
3. Never store equipment in a wet/damp environment.
LUBRICATION
Inspect and lubricate the tool when required. Only use light oil to lubricate the
tool. Other lubricants may not be suitable and could damage the tool or cause a
malfunction during use.

9095746 20V Li-Ion Cordless Brushless Compact Band Saw V1.0
16 For technical questions call 1-800-665-8685
When not in use for an extended period, apply a thin coat of lubricant to the
steel parts to avoid rust. Remove the lubricant before using the tool again.
DISPOSAL
Recycle a tool damaged beyond repair at the appropriate facility.
Contact your local municipality for a list of disposal facilities or by-laws for
electronic devices, batteries, oil or other toxic liquids.
IMPORTANT! DO NOT pollute the environment by allowing uncontrolled
discharge of waste oil.
TROUBLESHOOTING
Visit a Princess Auto Ltd. location for a solution if the tool does not function
properly or parts are missing. If unable to do so, have a qualified technician
service the tool.
Problem(s)
Possible Cause(s)
Suggested Solution(s)
Portable band saw
will not start.
1. Supplied power is
interrupted.
2. On/Off switch is
faulty.
3. Motor
components are
short-circuiting or
are defective.
4. Motor has
overheated.
5. The battery is not
installed correctly.
6. Battery power
depleted.
7. Battery is worn
out.
1. Check that power supply is still
available.
2. Replace faulty switch.
3.
Have a qualified technician service
the tool.
4. Allow motor to cool before
attempting to use.
5. Clean battery contacts
individually to avoid a shock. Then
install the battery correctly. Make
sure the polarity matches and the
battery locks into place.
6. Follow instructions to charge the
battery in Care & Maintenance.
7. Replace with a new battery from
the same manufacturer. Dispose
or recycle your old battery
according to your local municipal
bylaws.

V1.0 20V Li-Ion Cordless Brushless Compact Band Saw 9095746
Visit www.princessauto.com for more information 17
Problem(s) Possible Cause(s) Suggested Solution(s)
Motor starts slow
and doesn't reach
operation speed.
1. Motor is damaged.
2. The battery has
insufficient
charge.
3. Battery is worn
out.
1.
Have a qualified technician service
the tool.
2. Follow instructions to charge the
battery in Care & Maintenance.
3. Replace with a new battery from
the same manufacturer. Dispose
or recycle your old battery
according to your local municipal
bylaws.
Portable band saw
makes
unsatisfactory
cuts.
1. Dull or damaged
blade or incorrect
blade for work
being done.
2. Motor is
overloaded.
1. Replace blade with new/correct
blade.
2. Reduce pushing force on portable
band saw. See Operations for
proper use.
Tool is making
unusual sounds
1. Mechanical
obstruction.
2. Saw blade out of
balance.
3. The saw's parts
may be rubbing or
binding.
4. Electrical
components may
be shorting.
1.
Contact Princess Auto for solution.
2. Discard saw blade and replace
with a new blade.
3. Check for obstructions or
misaligned tool components.
Lubricate, repair or replace the
components based on the
particular problem.
4. Disconnect tool from the power
source immediately. Have the tool
examined by a qualified
technician.
Overheating 1. Forcing machine
to work too fast.
2. Dull Blade.
3. Blocked motor
housing vents.
1. Allow machine to work at its own
rate.
2. Keep the blade sharp. Replace as
needed
3. Blow dust out of motor using
compressed air.

9095746 20V Li-Ion Cordless Brushless Compact Band Saw V1.0
18 For technical questions call 1-800-665-8685

V1.0 20V Li-Ion Cordless Brushless Compact Band Saw 9095746
Visit www.princessauto.com for more information 19

9095746 20V Li-Ion Cordless Brushless Compact Band Saw V1.0
20 For technical questions call 1-800-665-8685