Power House PH2400PRi/E User manual

POWERHOUSE®
INVERTER GENERATOR
POWERHOUSE WEB SITE
Warranty Registration
Find a Dealer
Find a Service Center
PH 2400 PRi/E
WITH ELECTRONIC FUEL INJECTION
Owner’s Manual
PLEASE READ THIS MANUAL CAREFULLY
BEFORE OPERATING THE GENERATOR
TIP: To navigate between hyperlink topics using a keyboard, select ALT+◄ or ALT+►.

To navigate between hyperlink topics using a keyboard, select ALT+◄ or ALT+►. 2
Table of Contents
TABLE OF CONTENTS
PREFACE..............................................................................................................................................................4
PH2400PRi/E Identication Numbers...................................................................................................................................................5
Warranty Registration...................................................................................................................................................................................... 5
SAFETY ALERTS AND ICONS ..............................................................................................................................6
Safety Alert Icons..........................................................................................................................................................................................6
Informational Icons......................................................................................................................................................................................6
Hazard-Specic Safety Alerts...................................................................................................................................................................6
Carbon Monoxide (CO) Poisoning Alerts ............................................................................................................................................6
Explosion & Fire Alerts ...............................................................................................................................................................................6
Electrical & Electrocution Alerts..............................................................................................................................................................7
Operational Safety Alerts ..........................................................................................................................................................................7
Battery Safety Alerts ...................................................................................................................................................................................8
GENERATOR COMPONENTS................................................................................................................................9
PH2400PRi/E Generator.............................................................................................................................................................................9
PH2400PRi/E Access Doors ...................................................................................................................................................................10
PH2400PRi/E Control Panel...................................................................................................................................................................11
PH2400PRi/E Ignition Keys with USB.................................................................................................................................................11
PH2400PRi/E Remote Key Fob .............................................................................................................................................................11
PH2400PRi/E Digital LCD........................................................................................................................................................................12
Indicator Light...................................................................................................................................................................................................12
Display Reset Button.......................................................................................................................................................................................12
SETUP & PRE-OPERATION ................................................................................................................................ 13
Connecting the 12V Battery ..................................................................................................................................................................13
Charging the 12V Battery....................................................................................................................................................................... 13
Checking and Adding Engine Oil ........................................................................................................................................................15
Checking and Adding Fuel..................................................................................................................................................................... 16
STARTUP & SHUTDOWN .................................................................................................................................. 17
Ignition Key Startup..................................................................................................................................................................................17
Remote Startup ..........................................................................................................................................................................................18
Recoil Pull Startup ....................................................................................................................................................................................19
Shutdown .....................................................................................................................................................................................................20
GENERATOR OPERATION .................................................................................................................................21
Appliance Power Requirements...........................................................................................................................................................21
AC Application............................................................................................................................................................................................21
DC Application............................................................................................................................................................................................22
Powering a DC Device................................................................................................................................................................................... 22
Using Smart USB Ports.................................................................................................................................................................................. 22
Charging an External 12V Battery............................................................................................................................................................... 23
Environmental Impacts on Generator Performance.....................................................................................................................24
Clearing an Overload Condition..........................................................................................................................................................25
Clearing a Low Oil Condition (steady red light) ............................................................................................................................26
Clearing a Fault Condition (blinking red light)...............................................................................................................................27
Fault Codes .................................................................................................................................................................................................. 28

3
Table of Contents To navigate between hyperlink topics using a keyboard, select ALT+◄ or ALT+►.
PARALLEL MODE OPERATION ..........................................................................................................................29
Startup (Parallel Operation)................................................................................................................................................................... 30
Shutdown (Parallel Operation) .............................................................................................................................................................31
Using Parallel Mode to Run an Air Conditioner (13,500 –15,000 BTU).................................................................................. 31
Clearing an Overload Condition (Parallel Operation).................................................................................................................. 32
MAINTENANCE .................................................................................................................................................33
Maintenance Schedule............................................................................................................................................................................33
Changing the Engine Oil .......................................................................................................................................................................34
Cleaning the Air Filter Element ........................................................................................................................................................... 36
Cleaning the Spark Plug .........................................................................................................................................................................37
Cleaning the Spark Arrestor.................................................................................................................................................................. 38
Replacing the 12V Battery......................................................................................................................................................................39
TRANSPORTATION AND STORAGE ..................................................................................................................40
Transporting the Generator .........................................................................................................................................................................40
Exercising the Generator...............................................................................................................................................................................40
Short-Term Storage........................................................................................................................................................................................40
Long-Term Storage ........................................................................................................................................................................................40
TROUBLESHOOTING.......................................................................................................................................... 41
Engine Will Not Start ..............................................................................................................................................................................41
Appliance Does Not Operate ..............................................................................................................................................................42
No Output at the DC Receptacle .......................................................................................................................................................43
Engine Does Not Start with Remote Key Fob ................................................................................................................................43
Troubleshooting (Parallel Operation).................................................................................................................................................44
Identifying the Correct Parallel Kit ..............................................................................................................................................................44
Identifying Trouble During Parallel Operation......................................................................................................................................... 45
SPECIFICATIONS ...............................................................................................................................................46
WARRANTY AND CONSUMER INFORMATION ..................................................................................................47
POWERHOUSE® Generator Warranty............................................................................................................................................... 47
California Emission Control Warranty Statement..........................................................................................................................48
Emission Control System Warranty ....................................................................................................................................................49
APPENDIX A - EMISSION CONTROL SYSTEM .................................................................................................50
APPENDIX B - VEHICLE BATTERY CHARGING SAFETY ...................................................................................51
Table of Contents Continued...

To navigate between hyperlink topics using a keyboard, select ALT+◄ or ALT+►. 4
Table of Contents
PREFACE
Thank you for purchasing a POWERHOUSE® Inverter Generator.
This manual covers the operation and maintenance of a POWERHOUSE®PH2400PRi/E Inverter Generator.
This Owner's Manual is an essential part of the generator and must remain with it when lent to another user or upon
transfer of ownership.
• Content within this manual is based on the latest product information available at the time of publishing.
• Updates to this manual are available to download on the www.powerhouse-products.com website.
• We reserve the right to make changes at any time without notice and without incurring any obligation.
• No part of this publication may be reproduced without written permission.
© LKQ Specialty Products Group, 2018. All rights reserved. v. 1.0, 2018-11-27
FCC Notice
Trade Name: LKQ Specialty Products Group / Model: PH2400PRi/E
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Pursuant to FCC regulations, do not to make any changes or modifications to the remote control transmitter or
receiver that are not expressly approved by LKQ Specialty Products Group. Doing so could void your authority to
operate the equipment and will void the warranty.
Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

5
Table of Contents To navigate between hyperlink topics using a keyboard, select ALT+◄ or ALT+►.
PH2400PRi/E Identication Numbers
The engine serial number (ESN) and the generator barcode number (BCN) identify your particular unit and are
necessary when ordering parts and accessories. These two numbers are required for warranty administration.
Engine Serial Number (ESN)
The ESN is stamped on the engine block above the oil dipstick. It is visible when the maintenance door is removed.
Serial number
Barcode Number (BCN)
The BCN is found:
1. On the left side of the generator, at the bottom left of the maintenance door.
2. If you have the shipping carton for your generator, the BCN is also on the foil label on the carton.
BCN # 100122377055322
Sample BCN
Please record your generator identification numbers below and keep this manual in a safe place along with the bill of
sale.
Engine Serial Number (ESN)
Barcode Number (BCN)
Date of Purchase
Name of Selling Dealership
Warranty Registration
Register your unit today at www.powerhouse-products.com/new-unit-registration-form/. Online registration is accepted
as proof of purchase and significantly speeds up identification of your generator with warranty support.
For warranty assistance:
Phone: [phone]
Fax: [phone]
E-mail: [email protected]

To navigate between hyperlink topics using a keyboard, select ALT+◄ or ALT+►. 6
Table of Contents
SAFETY ALERTS AND ICONS
This generator is designed to give safe and dependable service if operated according to instructions. Read and
understand this Owner’s Manual and all safety alerts and labels before operating the generator.
Carbon Monoxide (CO) Poisoning Alerts
CO
Explosion & Fire Alerts
▲GENERATORS PRODUCE CARBON MONOXIDE FROM
EXHAUST GAS. Carbon monoxide is a poisonous, colorless,
odorless gas. When inhaled, CO can build up to dangerous
levels in the bloodstream and cause unconsciousness, leading to
serious injury or death within minutes.
▲NEVER RUN THE GENERATOR IN AN ENCLOSED OR PARTLY
ENCLOSED AREA, which leads to overheating, fire, or carbon
monoxide (CO) poisoning leading to serious injury or death
within minutes. Always ensure adequate ventilation.
▲Do not install this generator inside a compartment.
▲Generators should be used outdoors only, at least 3ft. (1m)
away from buildings, open windows, and other equipment, and
protected from rain and snow.
▲Do not modify the enclosure of this generator or use the
generator for purposes other than its intended use.
▲Do not connect an extension to the exhaust pipe.
▲Gasoline is extremely flammable and explosive under
certain conditions. High temperatures inside could cause
residual fuel to vaporize resulting in possible explosion.
▲Keep cigarettes, sparks, and any source of ignition away
from generator and the fuel tank at all times.
▲Operate the generator on a level surface. If the generator is
tilted, fuel spillage may result.
▲Check for spilled fuel or leaks. Clean and/or repair before
use. If any fuel is spilled, allow all fuel to evaporate before
starting the engine.
▲Always stop engine before refueling. Wait 5 minutes before
restarting and allow all fuel to evaporate.
▲Be careful not to spill fuel when refueling. Spilled fuel or
fuel vapor may ignite.
▲Refuel in a well-ventilated area with the engine stopped.
Safety Alert Icons
The following safety alert icons are used throughout this manual to
alert you to potential hazards. Obey all safety messages to avoid
injury or death.
ICON MEANING
!
CO
▲Alerts you to a hazardous situation
which, if not avoided, will result in
death or serious injury.
!
▲Alerts you to a hazardous situation
which, if not avoided, could result in
death or serious injury.
!
▲Alerts you to a hazardous situation
which, if not avoided, could result in
minor or moderate injury.
Alerts you to important safety tips or
required safety topics before performing
a task.
Hazard-Specic Safety Alerts
Informational Icons
The following icons call your attention to
information about the setup, operation, or
maintenance of your generator.
ICON MEANING
i
Especially helpful information
when using the generator.
Link to a related topic, an
internet resource, or an
email address.
Setup or preparation is
required before performing
a task.
Regular maintenance is
required.
Take precaution to avoid
damage to the generator.

7
Table of Contents To navigate between hyperlink topics using a keyboard, select ALT+◄ or ALT+►.
Electrical & Electrocution Alerts
▲To prevent electrical shock, the generator should be grounded.
Connect a length of heavy cable between the generator’s
grounding terminal and an external ground source.
▲To avoid a potential shock, make sure that all appliances are in
good working order before connecting them to the generator.
▲If an appliance begins to operate abnormally, becomes
sluggish, or stops suddenly, turn off the generator immediately.
Disconnect the appliance and examine it for signs of
malfunction.
▲Do not operate with wet hands. Generators are a potential
source of electrical shock when misused.
▲Do not operate the generator in rain or snow and do not let it
get wet.
▲Do not exceed the current limit specified for any one
receptacle.
▲Do not connect the generator to a household circuit.
This could cause damage to the generator or to electrical
appliances in the house.
▲This portable generator is designed for temporary power
needs. If you need a back-up power system for your home,
install a permanent stationary generator designed for this
purpose.
▲When an extension cord is required, be sure to use an
insulated flexible cord. Also be sure to use the proper size
and length cord.
• A 16 Gauge Cord between 0 and 100 feet long will safely
handle tool and appliance loads up to 10 amps.
• A 14 Gauge Cord between 0 and 50 feet long will safely
handle tool and appliance loads between 10 and 15 amps.
• A 12 Gauge Cord between 50 and 100 feet will safely handle
tool and appliance loads between 10 and 15 amps.
▲Keep the generator away from other electric cables or
commercial power supply lines.
▲Never connect this generator to a manual or automatic
transfer switch (ATS), which may result in severe damage to
the generator or personal property, and/or severe personal
injury or death. Back feed may also electrocute utility
company workers or others who contact the lines during a
power outage. When utility power is restored, the generator
may explode, burn, or cause a fire in the building’s electrical
system.
Operational Safety Alerts
!
▲Never permit anyone to operate the generator without proper
instructions.
▲Know how to stop the generator quickly and understand
operation of all controls.
▲Always perform a pre-operation inspection before you start the
engine to avoid accidents or equipment damage.
▲Keep away from moving parts while the generator is running.
▲Do not operate the generator on an uneven surface, such as
sand, mud, or dense wet grass, which may restrict airflow to
the generator and its components, resulting in overheating and
potential damage.
▲Be careful not to touch the muffler while it is hot. The
muffler becomes very hot during operation and remains
hot for several minutes after the engine is off.
▲Let the engine cool before storing the generator indoors.
▲Keep children and pets away from the generator when it is
in operation.
▲Avoid repeated or prolonged skin contact with fuel or
breathing of fuel vapor.

To navigate between hyperlink topics using a keyboard, select ALT+◄ or ALT+►. 8
Table of Contents
Battery Safety Alerts
▲Battery electrolyte is poisonous. If swallowed, drink large quantities of water or milk and follow
with milk of magnesia or vegetable oil and seek medical help immediately.
▲Batteries give off explosive gases; keep sparks, flames and cigarettes away. Provide adequate
ventilation when charging.
▲Do not use the generator to charge any other type of external battery except a 12V lead acid
battery. Other types of batteries may burst causing personal injury or damage.
!
▲Batteries contain sulfuric acid (electrolyte). Contact with skin or eyes may cause severe burns.
Wear protective clothing and a face shield.
▲If electrolyte gets on your skin, flush with water.
▲If electrolyte gets in your eyes, flush with water for at least 15 minutes and seek medical help
immediately.
▲Keep batteries out of reach of children.

9
Table of Contents To navigate between hyperlink topics using a keyboard, select ALT+◄ or ALT+►.
GENERATOR COMPONENTS
PH2400PRi/E Generator
FRONT OF GENERATOR, Right Side
Fuel Access Door Spark Plug Access Door
Recoil Starter Grip
PH2400PRi/E
Control Panel
Extendable
Handle
BACK OF GENERATOR, Left Side
Maintenance Access Door
Battery Access Door
Wheels
Exhaust Grille

To navigate between hyperlink topics using a keyboard, select ALT+◄ or ALT+►. 10
Table of Contents
PH2400PRi/E Access Doors
Your generator has four primary access doors. You can remove the access doors as shown below when performing
setup and maintenance.
Fuel Access DoorBattery Access Door
Maintenance Access Door Spark Plug Access Door

11
Table of Contents To navigate between hyperlink topics using a keyboard, select ALT+◄ or ALT+►.
PH2400PRi/E Control Panel
*The parallel power receptacle enables you to increase your power output when you own the optional parallel kit (#67164) and a
second compatible POWERHOUSE® generator for Parallel Mode Operation.
Parallel Power
Receptacle*
Smart
USB Ports:
2 x 1A ea
or
1 x 2A total
DC 12V 8.3A
Receptacle
(Battery Charging)
DC Circuit
Breaker
Overload
Reset
Button
(green)
AC Circuit
Breaker
AC Receptacle
120V 20A Duplex
PH2400PRi/E Digital LCD
Ground Terminal
Remote
Switch
Ignition Key Switch
(OFF, ON, and START)
Parallel Mode Operation | Ignition Key Startup | Remote Startup
PH2400PRi/E Ignition Keys with USB
Your generator comes with two ignition keys and one
USB flash drive with a digital Owner's Manual.
PH2400PRi/E Remote Key Fob
Your generator comes with two remote key fobs to use
when starting the generator from up to 75ft. away with an
unobstructed line of sight.
≤ 75Ft (22m)
Remote
START Button
Remote
STOP Button

To navigate between hyperlink topics using a keyboard, select ALT+◄ or ALT+►. 12
Table of Contents
PH2400PRi/E Digital LCD
Use the digital LCD (liquid crystal display) on the control panel to monitor the generator's operating status.
Digital LCD
When the generator is running, the LCD illuminates to display real-time data for voltage, amps, watts, total hours of
operation, and approximate fuel level.
LINE OF DATA LCD OUTPUT / UNIT OF MEASURE
U : (voltage source)
FUEL
T: 000.0 H
P: 0000 W
I: 00.0 A
U: 000.0 V
Voltage
I : (current) Amps
P : (power) Watts
T : (time) Hours of operation
Includes initial startup and testing hours at
the factory.
FUEL Fuel Level (Full tank is 5 bars)
Each vertical bar represents approximately
20% of total fuel remaining.
Indicator Light
The Indicator Light (red) illuminates to alert you of the
following operating conditions:
• Low Oil (steady red light)
• Fault Condition (blinking red light)
FUEL
T: 000.0 H
P: 0000 W
I: 00.0 A
U: 000.0 V
Steady red light
indicates a low oil
condition
Display Reset Button
The Display Reset Button enables you to view and clear
fault codes.
FUEL
T: 000.0 H
P: 0230 W
I: 00.0 A
U: 000.0 V
Press reset button
to toggle display
of fault code(s)
Blinking red light
indicates a fault
condition(s)
Clearing a Low Oil Condition | Clearing a Fault Condition

13
Table of Contents To navigate between hyperlink topics using a keyboard, select ALT+◄ or ALT+►.
SETUP & PRE-OPERATION
▲Ensure that the generator is OFF and on a level surface for all setup and pre-operation checks.
▲When working with a battery, read and comply with all Battery Safety Alerts and warnings.
Your generator ships from the factory in a pre-operation state. In this section, to enable generator startup, you
will complete the following steps: 1) Connect and 2) charge the 12V battery completely, 3) add engine oil, and 4)
add fuel.
Connecting the 12V Battery
To connect the 12V battery:
1. On the left side of the generator, remove the screw and the Battery Access Door.
2. Plug the quick connect cable into the wiring harness.
3. Reinstall the battery access door and screw back onto the generator.
Charging the 12V Battery
i
The generator does not have to be running to back-charge the battery, and there are no special control panel
settings to enable the battery to charge.
!
▲Do not use a battery charger that exceeds 12V 5A, which may cause the battery to swell and burst
leading to personal injury and property damage.
▲To prevent over-charging, use a battery charger with an automatic shut-off feature.
To charge the 12V battery:
1. Choose an option to connect battery charging cables.
To connect an external 12V (max 5A) battery charger to the DC receptacle:
a. Connect the positive and negative alligator clips to the corresponding wires on the 12V charger.
b. Plug the T-style end of the charging cable into the DC receptacle.

To navigate between hyperlink topics using a keyboard, select ALT+◄ or ALT+►. 14
Table of Contents
To connect directly to the battery:
a. Remove the battery access door and screw.
b. Unplug the quick connect cable from the wiring harness.
c. Remove the battery hold down strap, then remove the battery.
d. Connect the positive and negative alligator clips of your charging cables to the corresponding battery terminals.
2. Charge the battery for 3 hours or until fully charged.
3. When the battery is fully charged:
• After back-charging, disconnect the battery charger from the DC receptacle.
• After charging the battery directly, reinstall the 12V battery and the battery access door and screw.
Because a lead acid battery may become depleted when it's not in use, remember to recharge the 12V battery
after long-term storage.
Replacing the 12V Battery

15
Table of Contents To navigate between hyperlink topics using a keyboard, select ALT+◄ or ALT+►.
Checking and Adding Engine Oil
Engine oil capacity: 15.6 fl oz (0.97 pt) / 460 ml
Use a premium quality, 4-stroke engine oil that is a certified API grade SF/SG or better.
• For environmental temperatures above 32°F (0°C), use SAE 10W-30 viscosity oil.
• For environmental temperatures below 32°F (0°C), use SAE 0W-30 or 0W-40 viscosity oil, preferably synthetic.
▲Do not use non-detergent oil or 2-stroke engine oil which voids the warranty and shortens the service life of
the engine.
▲Running the engine with insufficient oil can cause serious engine damage.
To check and add oil:
1. On the left side of the generator, remove the screw and the Maintenance Access Door.
2. Remove the dipstick from the oil reservoir, then wipe it with a clean rag.
3. Check the oil level and add oil if necessary. Insert the dipstick back into the oil reservoir, remove it, and check the oil level.
(To ensure an accurate reading, do not tighten or screw the dipstick into the reservoir.)
a. If the oil level is at the bottom of the etching on the dipstick, rell with recommended oil. Do not overll.
b. After relling, check the oil level again, and ensure that the oil level is at the top of the etching on the dipstick.
Low oil level
at bottom of etching
Full oil level
at top of etching
4. Reinsert and tighten the dipstick in the oil reservoir.
5. Reinstall the maintenance door and screw back onto the generator.
◊ Change the oil after the first 4 to 6 hours of operation to remove any manufacturing debris or contamination.
◊ The low oil alarm system automatically stops the engine before the oil level falls below a safe limit. However, to
avoid the inconvenience of an unexpected shutdown, visually inspect the oil level before each use.
Extreme Temperatures | Clearing a Low Oil Condition | Changing the Engine Oil

To navigate between hyperlink topics using a keyboard, select ALT+◄ or ALT+►. 16
Table of Contents
Checking and Adding Fuel
Fuel tank capacity: 1.2 gal (4.7 L)
▲Before adding fuel to the generator, read and comply with all Safety Alerts and Icons.
▲Read and comply with all Explosion & Fire Alerts when adding fuel to the generator.
Cautions on Gasoline Blends
▲Use only automotive unleaded gasoline in the generator, preferably with an octane rating of 87 or higher.
▲Never use an oil/gasoline mixture or dirty gasoline.
▲Make sure you do not use a fuel blend with more than 10% ethanol. If you notice any undesirable operating
symptoms, replace it with a fuel that you know has the proper blend.
▲Do not use gasoline containing methanol.
▲Fuel system damage or engine performance problems, caused by improper fuel blend are not covered under
warranty.
To check and add fuel:
1. Ensure that the generator is OFF.
2. Remove the fuel cap and visually check the fuel level.
3. If fuel is low, pour fuel slowly through the fuel strainer. Do not overll. Because the fuel strainer is positioned at an angle, rell to the
lowest shoulder of the fuel strainer.
Add fuel to the lowest
shoulder of the fuel strainer
i
◊ Avoid getting dirt, dust, or water in the fuel tank.
◊ Temperature changes affect the volume of gasoline. Make sure that you leave extra room at the top of the tank
when you refuel to allow for fuel expansion on warm days.
◊ Use a fuel stabilizer, such as STA-BIL® to help prevent fuel oxidation (breakdown), formation of gum and varnish,
and corrosion in the fuel system.
When adding fuel to the tank for the rst time (and after every 100 hours of operation), it is recommended that
you use a fuel injector cleaner.
4. Replace and tighten the fuel cap securely.
Transportation and Storage

17
Table of Contents To navigate between hyperlink topics using a keyboard, select ALT+◄ or ALT+►.
STARTUP & SHUTDOWN
You can start the generator using any of the following methods:
• Ignition Key Startup at the control panel
• Remote Startup using the remote switch at the control panel and the remote key fob
• Recoil Pull Startup using the recoil handle on the right side of the generator
Ignition Key Startup
▲Before using the generator, read and comply with all Safety Alerts and Icons.
Before starting the generator, make sure the 12V battery is fully charged. The generator requires at least 10.5
cranking volts of battery charge to provide power for startup components and sensors.
To start the generator with the ignition key:
1. On the control panel, verify that the remote switch is in the OFF position.
2. Insert the ignition key, then turn and hold the ignition key in the START position. The LCD on the control panel illuminates.
i
Once the ignition switch is ON, if you do not start the generator within 30 seconds, the LCD dims to conserve
battery power.
If the engine does not start within 15 seconds, stop turning the key for 5 seconds before trying it again.
START
The LCD shows output voltage when the generator is ready for use.
3. Connect your appliance to the generator's output receptacle.
i
Make sure that appliances are in good working condition and that the combined electrical rating of all
connected appliances does not exceed that of the generator (2400W max). If you don't know the watts for your
appliance, multiply the amperage by the output voltage. For example: 20A x 120V = 2400W.
4. Turn your appliance on.
Shutdown | Clearing an Overload Condition | Parallel Mode Operation

To navigate between hyperlink topics using a keyboard, select ALT+◄ or ALT+►. 18
Table of Contents
Remote Startup
▲Before using the generator, read and comply with all Safety Alerts and Icons.
Before starting the generator, make sure the 12V battery is fully charged. The generator requires at least 10.5
cranking volts of battery charge to provide power for startup components and sensors.
To start the generator with the remote key fob:
1. Verify that the ignition switch is in the OFF position.
2. On the control panel, set the remote switch to the ON position. The LCD on the control panel illuminates.
i
Once the remote switch is ON, if you do not start the generator within 30 seconds, the LCD dims to conserve
battery power.
3. Using the remote key fob, press and hold the gray start button for several seconds until the engine starts. Release and
repeat if necessary.
Press to
START
≤ 75Ft (22m)
i
◊ When using the remote key fob, make sure you have an unobstructed line of sight to the generator and are no
farther than 75ft. away.
◊ When pressing the start button on the remote key fob, there is a 1–3 second delay before the engine cranks while
the fuel system reaches the proper pressure.
◊ For additional help, see Troubleshooting: Engine Does Not Start with Remote Key Fob.
The LCD shows output voltage when the generator is ready for use.
4. Connect your appliance to the generator's output receptacle.
i
Make sure that appliances are in good working condition and that the combined electrical rating of all
connected appliances does not exceed that of the generator (2400W max). If you don't know the watts for your
appliance, multiply the amperage by the output voltage. For example: 20A x 120V = 2400W.
5. Turn your appliance on.
Shutdown with Remote Key Fob | Clearing an Overload Condition

19
Table of Contents To navigate between hyperlink topics using a keyboard, select ALT+◄ or ALT+►.
Recoil Pull Startup
▲Before using the generator, read and comply with all Safety Alerts and Icons.
Before starting the generator, make sure the 12V battery is fully charged. The generator requires at least 10.5
cranking volts of battery charge to provide power for startup components and sensors.
To pull-start the generator using the starter grip:
1. Verify that the remote switch is in the OFF position.
2. Insert and turn the ignition key to the ON position. The LCD on the control panel illuminates.
ON
i
Once the ignition switch is ON, if you do not start the generator within 30 seconds, the LCD dims to conserve
battery power.
3. On the right side of the generator, grasp the starter grip and pull back lightly until resistance is felt, then pull briskly out. Repeat until
the engine starts. Faster pulls generate more spark and enable successful startup.
!
▲Do not allow the starter grip to snap back. Return it slowly by hand.
▲Do not pull the starter grip while the generator is running.
▲Do not let the starter rope rub against the generator body or the rope will wear out prematurely.
The LCD shows output voltage when the generator is ready for use.
4. Connect your appliance to the generator's output receptacle, then turn the appliance on.
i
Make sure that appliances are in good working condition and that the combined electrical rating of all
connected appliances does not exceed that of the generator (2400W max). If you don't know the watts for your
appliance, multiply the amperage by the output voltage. For example: 20A x 120V = 2400W.
Shutdown | Clearing an Overload Condition

To navigate between hyperlink topics using a keyboard, select ALT+◄ or ALT+►. 20
Table of Contents
Shutdown
◊ You must shut down the generator using the same method you chose for startup.
To shut down the generator:
1. Turn o any appliances connected to the generator.
2. Shut down the generator using the same method you chose for startup.
If you started the generator with the ignition key or recoil starter grip:
–On the control panel, turn the ignition key to the OFF position to shut down the generator.
–Verify that the remote switch is in the OFF position.
OFF
OFF
If you started the generator with the remote key fob:
–On the remote key fob, press the STOP button to shut down the generator.
Press to
STOP
–On the control panel, set the remote switch to the OFF position.
i
If you leave the remote switch ON:
◊ You can use the remote key fob to restart the generator within 12 hours of shutdown.
◊ After 12 hours, the generator automatically hibernates to conserve battery power. To deactivate hibernation and
re-enable startup, you must toggle the remote switch: OFF–ON.
Shutdown (Parallel Operation)