Power House PH2700PRi User manual

PH2700PRi OM revision 2010-10-07
PH2700PRi Digital Inverter Generator
Operating Instructions
OPERATING
INSTRUCTIONS
PLEASE READ THIS MANUAL
CAREFULLY
BEFORE USING

2 PH2700PRi OM revision 2010-10-07
QUICK START
Use outdoors only. Generators produce carbon monoxide —a poisonous, colorless,
odorless gas that can cause death or serious injury.
Always operate on a level surface.
Keep away from rain, snow or other wet conditions.
Keep away from smoking materials, sparks, and other sources of combustion when
refueling.
Pre-Operation:
1. Check the oil level by removing the maintenance cover and inspecting the dipstick. Fill reservoir with 16 oz (0.50 L) oil or
to the full mark on the dipstick. Use appropriate grade, high-detergent, premium quality, 4-stroke engine oil.
2. Remove the battery access cover and connect the battery.
3. Add regular unleaded automotive gasoline up to the shoulder of the fuel strainer. Avoid getting dirt, dust, or water in the
fuel tank. Do not use a blend that contains more than 10% ethanol. Do not use gasoline containing methanol. Octane
rating of 87 or higher is recommended.
Operation For operation at high altitudes and in extreme temperatures, see the complete operating
instructions.
1. Ensure that no loads have been connected to the AC receptacles.
2. Open the fuel valve. If the fuel tank was empty, it may be necessary to pump the primer bulb to get fuel to the carburetor.
3. Start the engine in one of the following ways.
A. Electric Start:
Insert the ignition key, and turn it all the way to the START position. Hold key at this position until the
engine is running or for a maximum of 10 seconds. Release and repeat if necessary.
B. Manual Start:
Turn the ignition switch to the ON position.
Pull the starter grip lightly until resistance is felt, then pull briskly out.
C. Remote Start:
Turn the remote switch to the ON position.
Push the start button on the remote twice and hold until the engine has started or for a maximum of 10
seconds. Release and repeat if necessary.
Always turn the remote switch to the ―OFF‖ position when not in use to prevent running down the battery.
4. The green ―run‖light will illuminate when the generator is ready for use. Before connecting any loads, ground the
generator with a length of heavy cable, connecting the generator’s grounding terminal to an external ground source.
5. Make sure that all appliances to be connected have been switched off and are in good working order. Confirm that the
electrical rating does not exceed that of the generator.
6. Connect the appliance to the appropriate receptacle on the generator’s panel.
7. To minimize fuel consumption and noise, turn on the Economy switch. This setting regulates the engine’s speed so that it
matches the needs of the connected loads.
Shutdown In an emergency, pushing the STOP button on the control panel will automatically stop the
engine without the ignition key or remote, with or without a load. However, continually
stopping the generator without disconnecting all loads can cause damage to the generator
or appliances.
1. Turn off all connected appliances and disconnect from the generator.
2. Use one of the following methods to turn off the generator
A. If the remote switch is OFF:
Turn the ignition key to the STOP position.
B. If the remote switch is ON:
Push and hold the stop button on the remote or on the panel.

3 PH2700PRi OM revision 2010-10-07
PREFACE
Thank you for purchasing a POWERHOUSE® generator.
This manual covers the operation and maintenance of the POWERHOUSE® generator model PH2700PRi.
All information in this publication is based on the latest product information available at the time of approval for
printing.
We reserve the right to make changes at any time without notice and without incurring any obligation.
No part of this publication may be reproduced without written permission.
This manual should be considered a permanent part of the generator and should remain with it if it is resold.
Pay special attention to statements preceded by the following words:
Indicates a strong possibility of severe personal injury or death if instructions
are not followed.
Indicates a possibility of personal injury or equipment damage if instructions
are not followed.
Gives helpful information.
Failure to properly follow these precautions can result in property damage,
serious injury, or DEATH!
Read all labels and the owner's manual before operating this generator.
Generators produce carbon monoxide —a poisonous, colorless, odorless
gas that can cause death or serious injury.
Indoor use of a generator can kill quickly. Generators should be used
outdoors only.
Generators should only be used outdoors, away from garages and open
windows, but protected from rain and snow.
Check for spilled fuel or leaks. Clean and/or repair before use.
Always stop engine before refueling. Wait 5 minutes before restarting.
Keep any source of ignition away from fuel tank, at all times.
The portable generator is not meant to be used as a permanent back-up
power system for the home.Apermanently installed stationary generator is
designed to be safely used for this specific purpose.
If a problem should arise, or if you have any questions about the generator, consult an authorized dealer.
Our generators are designed to give safe and dependable service if operated
according to instructions. Read and understand the Owner's Manual before
operating the generator. Failure to do so could result in personal injury or
equipment damage.

4 PH2700PRi OM revision 2010-10-07
FCC INFORMATION
Trade Name: Coast Distribution Inc.
Model: PH2700PRi
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Pursuant to FCC regulations, do not to make any changes or modifications to the remote control transmitter or
receiver that are not expressly approved by Coast Distribution Inc. Doing so could void your authority to operate
the equipment and will void the warranty.
Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

5 PH2700PRi OM revision 2010-10-07
CONTENTS
OPERATING INSTRUCTIONS..............................................................................................................................1
QUICK START........................................................................................................................................................2
Pre-Operation:....................................................................................................................................................2
Operation............................................................................................................................................................2
Shutdown............................................................................................................................................................2
PREFACE...............................................................................................................................................................3
FCC INFORMATION..............................................................................................................................................4
Notice..................................................................................................................................................................4
CONTENTS............................................................................................................................................................5
1. SAFETY INSTRUCTIONS .................................................................................................................................7
2. COMPONENT IDENTIFICATION.......................................................................................................................9
2.1 Control panel, PH2700PRI.........................................................................................................................10
2.2 Serial number and bar code identification and location............................................................................. 11
3. PRE-OPERATION CHECK.............................................................................................................................. 11
3.1 Check the engine oil level...........................................................................................................................12
3.2 Check the fuel level. ...................................................................................................................................13
3.3 Check the air cleaner..................................................................................................................................14
3.4 Connecting the battery ...............................................................................................................................15
3.5 Battery Removal.........................................................................................................................................15
4. OPERATING INSTRUCTIONS ........................................................................................................................16
4.1 Starting the engine......................................................................................................................................16
4.2 Starting procedure using the ignition key...................................................................................................16
4.3 Manual Start................................................................................................................................................17
4.4 Starting procedure using the remote function ............................................................................................18
4.5 High altitude operation................................................................................................................................19
4.6 Generator use.............................................................................................................................................20
4.7 AC application.............................................................................................................................................22
4.8 Output and Overload Lights........................................................................................................................23
4.9 DC application ............................................................................................................................................24
4.10 Low oil alarm system................................................................................................................................26
4.11 Economy switch........................................................................................................................................26
4.12 Stopping the engine..................................................................................................................................27
5. PARALLEL GENERATOR OPERATION (with optional kit # 69276) ...............................................................28
5.1 Parallel operating features..........................................................................................................................28
5.2 Air Conditioning Operation (13,500-15,000 Btu)........................................................................................28
6. MAINTENANCE ...............................................................................................................................................29
6.1 Emission control system.............................................................................................................................29
6.2 Maintenance Schedule...............................................................................................................................31
6.3 Changing oil................................................................................................................................................32
6.4 Air cleaner service ......................................................................................................................................33
6.5 Spark plug maintenance.............................................................................................................................34
6.6 Spark arrestor maintenance .......................................................................................................................36
7. TRANSPORTING & STORAGE.......................................................................................................................37
7.1 Exercising the Generator............................................................................................................................37
7.2 Before storing the unit for an extended period...........................................................................................38
8. TROUBLESHOOTING .....................................................................................................................................39
8.1 Engine will not start.....................................................................................................................................39
8.2 Appliance does not operate:.......................................................................................................................40
8.3 No output at the DC receptacle:.................................................................................................................40
9. SPECIFICATIONS............................................................................................................................................41

6 PH2700PRi OM revision 2010-10-07
10. WARRANTYAND CONSUMER INFORMATION..........................................................................................42
POWERHOUSE® GENERATOR WARRANTY ...............................................................................................42
CALIFORNIA EMISSIONS CONTROL WARRANTY STATEMENT ................................................................43
EMISSION CONTROL SYSTEM WARRANTY................................................................................................44
11. APENDIX B - EMISSION CONTROL SYSTEM.............................................................................................45
12. APENDIX C - SAFETYAND CHARGING INSTRUCTIONS..........................................................................46

7 PH2700PRi OM revision 2010-10-07
1. SAFETY INSTRUCTIONS
■This generator is designed to give safe and dependable service if operated
according to instructions.
Read and understand the Owner's Manual before operating the generator. Failure to
do so could result in personal injury or equipment damage.
■Exhaust gas contains poisonous carbon monoxide. Never run the generator in an
enclosed area.
Be sure to provide adequate ventilation.
■The muffler becomes very hot during operation and remains hot for several minutes
after stopping the engine.
Be careful not to touch the muffler while it is hot.
Let the engine cool before storing the generator indoors.
To ensure safe operation
Gasoline is extremely flammable and explosive under certain conditions. Refuel in a
well ventilated area with the engine stopped.
Keep away from cigarette smoke and sparks when refueling the generator.
Wipe up spilled gasoline at once.

8 PH2700PRi OM revision 2010-10-07
■This generator is not intended, nor designed, for use as a standby power supply and
should never be used as such. Severe property damage and/or severe personal
injury or death may result. Never connect this generator to an automatic transfer
switch (ATS). Severe damage to the generator will occur.
■Always make a pre-operation inspection before you start the engine. You may
prevent an accident or equipment damage.
■Place the generator at least 3 ft (1 m) away from buildings or other equipment during
operation.
■Operate the generator on a level surface. If the generator is tilted, fuel spillage may
result.
■Know how to stop the generator quickly and understand operation of all controls.
Never permit anyone to operate the generator without proper instructions.
■Keep children and pets away from the generator when it is in operation.
■Keep away from moving parts while the generator is running.
■The generator is a potential source of electrical shocks when misused; do not
operate with wet hands.
■Do not operate the generator in rain or snow and do not let it get wet.
■Do not install this generator inside a compartment. Doing so may lead to overheating
and consequently, fire. It may also lead to death by asphyxiation.
■Do not modify the enclosure of this generator.

9 PH2700PRi OM revision 2010-10-07
2. COMPONENT IDENTIFICATION
Gas Cap Access
Cover
Control Panel
Retractable
Handle
Spark Plug
Access Cover
Maintenance
Cover
Starter Grip
Primer Bulb
Fuel Lever
Battery Access
Cover
Wheels

10 PH2700PRi OM revision 2010-10-07
2.1 Control panel, PH2700PRI
Parallel
Communication
Port
Parallel Socket
Overload Indicator
Light (Red)
Low Oil Alarm
(Red)
Run Light (Green)
Overload Reset
Button (Green)
Stop Button
(Red)
Battery Charge
Receptacle
12V ~ 8.3A
Economy Switch
Remote switch
Battery Charge
Circuit Breaker
Ground
Terminal
120V Circuit
Breakers
2-120V ~ 20A
Receptacles
Ignition
Switch
Cover
ON OFF ON OFF

11 PH2700PRi OM revision 2010-10-07
2.2 Serial number and bar code identification and location
The generator serial number identifies your particular unit and is necessary when ordering parts and accessories.
The bar code is used by your dealer and Coast Distribution for warranty administration and must be supplied
before any work can be done.
The serial number can be found stamped on the engine block
above oil dipstick. It is visible when the maintenance panel is
removed.
The bar code label is found in two locations:
1. On the bottom of the generator.
2. On the packing carton.
Please record this information below and keep this manual in a safe place along with the bill of sale.
Engine Serial Number __________________________________
Bar Code Number _______________________________
Date of Purchase ________________________________
Name of Selling Dealership ________________________________
Please go to www.powerhouse-products.com/register and register your unit today. Online registration will
be accepted as proof of purchase. Online registration will make sure you are protected in the event you have
lost your receipt, and will significantly speed the process in the event warranty service is necessary.
For warranty assistance:
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
Serial Number

12 PH2700PRi OM revision 2010-10-07
3. PRE-OPERATION CHECK
■Be sure to check the generator on a level surface with the engine stopped.
3.1 Check the engine oil level.
Do not use non-detergent oil or 2-stroke engine oil. It will void the warranty and
will shorten the engine's service life.
Use a high-detergent, premium quality, 4-stroke engine oil, certified to meet or
exceed U.S. automobile manufacturer's requirements for API Service
Classification SG/SF.
Select the appropriate viscosity for the average temperature in your area.
SAE Viscosity Grades
Ambient Temperature
1. Loosen the cover screw and remove the maintenance cover.
2. Wipe the dipstick with a clean rag, and reinsert the dipstick back into the filler neck, screwing it down
completely.
3. If the oil level is at or below the lower level of the dipstick, refill the recommended oil up to the top of the
upper level marking. Do not overfill.
■Running the engine with insufficient oil can cause serious engine damage.
■The Low OilAlarm System will automatically stop the engine before the oil level
falls below a safe limit. However, to avoid the inconvenience of an unexpected
shutdown, it is still advisable to visually inspect the oil level regularly.
Single
Viscosity
Multi-
viscosity
Upper Level
Lower Level
Upper Level
Dipstick

13 PH2700PRi OM revision 2010-10-07
3.2 Check the fuel level.
Use automotive unleaded regular gasoline only.
1. If the fuel level is low, refill to the shoulder of the fuel strainer.
2. Never use an oil/gasoline mixture or dirty gasoline.
3. Avoid getting dirt, dust or water in the fuel tank.
4. After refueling, tighten the fuel filler cap securely.
■Gasoline is extremely flammable and is explosive under certain conditions.
■Refuel in a well-ventilated area with the engine stopped. Keep all smoking materials,
sparks, and any other source of combustion away from the generator during refueling.
■Do not overfill the fuel tank (there should be no fuel above the upper limit mark).After
refueling, make sure the tank cap is closed properly and securely.
■Be careful not to spill fuel when refueling. Spilled fuel or fuel vapor may ignite. If any
fuel is spilled, make sure the area is dry before starting the engine.
■Avoid repeated or prolonged contact with skin or breathing of vapor. KEEP OUT OF
REACH OF CHILDREN.
Fuel tank capacity: 1.4 gal (5.2 liters)
Gasoline containing alternate fuels
Do not use a blend that contains more than 10% ethanol. Do not use gasoline containing methanol. Octane
rating of 87 or higher is recommended.
Fuel Cap
Fuel Strainer
Fuel Level

14 PH2700PRi OM revision 2010-10-07
Fuel system damage or engine performance problems resulting from the use of
fuels that contain an improper alcohol blend are not covered under warranty.
Before buying fuel from an unfamiliar station, determine if the fuel contains
ethanol and if it does, confirm the type and percentage of ethanol used. If you
notice any undesirable operating symptoms while using a gasoline that contains
ethanol, or one that you think contains ethanol, replace it with a gasoline that you
know has the proper blend.
3.3 Check the air cleaner
Check the air cleaner element to be sure it is clean and in good condition.
Loosen the panel screw and remove the maintenance cover.
Remove two air filter retaining screws. Remove the cover and check the element. Clean or replace the element if
necessary.
■Never run the engine without the air cleaner.
■Rapid engine wear will result from contaminants, such as dust and dirt being drawn
through the carburetor into the engine.
Air Cleaner
Case
Air Cleaner
Screws
Maintenance
Cover
Air Cleaner
Element
Screw
Air Cleaner
Cover

15 PH2700PRi OM revision 2010-10-07
3.4 Connecting the battery
1. Loosen the cover screw and remove the battery access cover.
2. To connect the battery, plug the 2 connectors together.
3.5 Battery Removal
1. To remove the battery for maintenance or replacement.
2. Loosen the cover screw and remove the battery access cover.
3. Unplug the battery and unhook the battery strap and slide out.
Battery
Connectors
Battery
Cover
Battery Strap

16 PH2700PRi OM revision 2010-10-07
4. OPERATING INSTRUCTIONS
4.1 Starting the engine
■This unit can be started by either the ignition key or remote. When the unit is
started with the ignition key, it can be shut down by the ignition key or the Emergency
shut-down button on the control panel; but NOT by the remote. When the unit is
started by the remote, it can be shut down by the remote. If you want to shut down
the unit with the ignition key when the unit has been started by remote, you will need
to turn the remote control switch on the control panel to the ―OFF‖position before
you can shut off the unit with the ignition key. The unit can always be shut down by
the Emergency button on the control panel no matter how you start the unit.
Before starting the engine, disconnect any load from theAC receptacles.
4.2 Starting procedure using the ignition key
1. Turn the fuel valve to the ―ON‖position.
2. If the fuel tank was empty it may be necessary to pump the primer bulb several times to get fuel to the
carburetor.
3. Move the remote selector switch to the ―OFF‖position.
4. Turn the ignition switch to the START position until the engine has started. Do not operate the starter for
more than 10 seconds. Repeat if necessary.
Remote
Switch
Primer Bulb
Fuel Valve

17 PH2700PRi OM revision 2010-10-07
4.3 Manual Start
1. Turn the fuel valve lever to the ―ON‖position.
2. If the fuel tank was empty it may be necessary to pump the primer bulb several times to get fuel to the
carburetor.
3. Move the remote selector switch to the ―OFF‖position.
4. Turn the ignition switch to the ―ON‖ position.
5. Pull the starter grip lightly until resistance is felt, then pull briskly out.
■Do not allow the starter grip to snap back. Return it slowly by hand.
■Do not let the starter rope rub against the generator body or the rope will wear
out prematurely.
Fuel Valve
Primer Bulb

18 PH2700PRi OM revision 2010-10-07
4.4 Starting procedure using the remote function
1. Turn the fuel valve lever to the ―ON‖position.
2. Move the remote selector switch to the ―ON‖position.
3. If the fuel tank was empty it may be necessary to pump the primer bulb several times to get fuel to the
carburetor.
4. Push the start button on the remote twice and hold until the engine has started. Do not operate the
starter for more than 10 seconds. Repeat if necessary.
The maximum operating range is 75’ based on a clear line of site.
Always put the remote switch on the generator in the “OFF” position when not
in use, to prevent running down the battery.
Start
Button
Remote
Switch
Primer Bulb
Fuel Valve

19 PH2700PRi OM revision 2010-10-07
4.5 High altitude operation
At higher altitudes, the standard carburetor air-fuel mixture will be excessively rich. Performance will decrease,
and fuel consumption will increase. Power output will decrease 3.5% for each 1000 feet (305 m) above sea
level.
High altitude performance can be improved by installing a smaller diameter main fuel jet in the carburetor. If you
always operate the generator at altitudes higher than 5000 feet (1500 m) above sea level, have your authorized
dealer install a high altitude main jet.
Even with suitable carburetor jetting, engine horsepower will decrease approximately 3.5% for each 1000 feet
(305 m) increase in altitude. The affect of altitude on the horsepower will be greater than this if no carburetor
modification is made.
■Operation of the generator at an altitude lower than the carburetor is jetted for may
result in reduced performance, overheating, and serious engine damage caused by
an excessively lean air/fuel mixture.
■Be sure to have any modification reversed at lower altitudes.
Temperature
High temperature adversely affects generator operation. Generator performance will decrease 1% for each 10°F
(5.5°C) increase in temperature above 85°F (29°C). The normal operating range of this generator is -20° to 113°
F (-29° to 45°C).
■Do not operate the generator when the ambient temperature is below -20°F (-29°C).
■Do not operate the generator when the ambient temperature exceeds 113°F (45°C).

20 PH2700PRi OM revision 2010-10-07
4.6 Generator use
Be sure to ground the generator when loads are connected.
■To prevent electrical shock from faulty appliances, the generator should be grounded.
Connect a length of heavy cable between the generator's ground terminal and an
external ground source.
■Connections for standby power to a building's electrical system must be made by a
qualified electrician and must comply with all applicable laws and electrical codes.
Improper connections can allow electrical current from the generator to back feed into
the utility lines. Such back feed may electrocute utility company workers or others who
contact the lines during a power outage. When utility power is restored the generator
may explode, burn, or cause fires in the building's electrical system.
■Do not connect the generator to an automatic transfer device. Severe damage to the
inverter module may result.