Power Wheels Kawasaki ZX-7 78410 User manual

Kawasaki®ZX-7
Owner’s Manual with Assembly Instructions
Please read this manual and save it with your original sale’s receipt.
For Model 78410
Tools needed for assembly: Phillips Screwdriver, Slotted Screwdriver, Hammer, Safety Scissors.
Use only with Power Wheels®Type H Battery, Power Wheels®25 Amp Fuse and
Power Wheels®Type H 6 Volt Charger (all included).
CAUTION
ELECTRIC TOY: Not recommended for children under 11/2years of age.
As with all electric products, precautions should be observed during
handling and use to prevent electric shock.

WARNING
• Children can be harmed by small parts, sharp edges and sharp points in the vehicle’s
unassembled state, or by electrical items. Care should be taken in unpacking and assembly of
the vehicle. Children should not handle the battery or other parts, or help in assembly.
• Keep small parts and plastic bags out of children’s reach. Dispose of plastic bags properly.
• Adult supervision is required. Children do not have the judgement necessary to avoid many
accidents. Be sure that children operating this vehicle can do so safely and that they are
supervised at all times.
• Improper use of this vehicle could lead to a serious or fatal accident. Allow children to play
with the Kawasaki®ZX-7 only when you have determined that they can do so safely. Follow
all instructions to help your child enjoy this vehicle as safely as possible.
• Never use on or dangerously close to steps, inclines greater than 10˚, roadways, bodies of
water, low obstructions or in the dark.
• Always wear shoes or sneakers when operating this vehicle.
• Never allow more than one rider.
• The rider should sit on the seat when the vehicle is in motion.
• Observe the maximum weight limit of 50 lbs.
• Never alter this vehicle or its electrical system in any way. Alterations could cause a fire
resulting in injury and could also ruin the electrical system.
• Use of the wrong type battery, fuse or charger could cause a fire or explosion, resulting in
serious injury.
• Never add unauthorized parts to the vehicle or use substitute parts. Use only specified
Power Wheels®replacement parts.
• The battery must be handled by adults only.
• Never lift or carry the battery by the wires or connector. This can damage the battery and
possibly cause a fire. Lift and carry the battery by the case only.
• Never permit a child to handle the battery. The battery is heavy and contains sulfuric acid
(electrolyte), and if dropped, could result in serious injury. Read the cautions on the back panel
of the battery.
• Never allow children to charge the battery. Battery charging must be done by adults only.
A child could be injured by the electricity involved in charging the battery.
• Examine the battery, charger and their connectors for excessive wear or damage each time you
charge the battery. If damage or excessive wear is detected, do not use the vehicle until you
have replaced the worn or damaged part.
2
Throughout this manual you will find important messages in the
form of WARNINGS, CAUTIONS, and NOTES. WARNING
WARNING – SIGNALS SOMETHING THAT
COULD HURT YOUR CHILD OR YOU.
The message explains the hazard and
how you can avoid it.

CAUTION
• Do not operate the vehicle for the first time until you have inserted the 25 amp fuse into the
battery and charged the battery for at least 18 hours. Never charge the battery longer than
30 hours.
• After first-time use, recharge the battery for at least 18 hours after each use. Never charge the
battery longer than 30 hours.
• Use the charger indoors only.
• Read and follow the Battery Care instructions on page 26. Failure to follow the Battery Care
instructions may permanently damage your battery and will void your warranty.
• To avoid damaging the motor and gears, do not overload the vehicle.
- Never allow more than one child on the vehicle at one time.
- Do not exceed the maximum weight capacity of 50 lbs.
- Do not tow anything behind the Kawasaki®ZX-7. The extra weight may overload
the vehicle.
• Avoid operating the vehicle in wet or snowy conditions, and do not spray the vehicle with
a hose. Do not wash the vehicle with soap and water. Water or moisture in the motor or
electrical switches can cause them to corrode, and could cause switch failure.
• Avoid operating the vehicle on grass, sand, loose dirt or gravel. Sand, loose dirt and gravel in
the electrical switches or motor can cause them to jam, and could cause switch failure. Use
the Kawasaki®ZX-7 on asphalt, cement or other hard surfaces.
3
CAUTION
CAUTION – SIGNALS SOMETHING THAT
COULD DAMAGE THE VEHICLE.
The message explains the risk and
how you can avoid it.
NOTE – Is used to highlight
useful information.

Table of Contents
AMessage to Parents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
BImportant Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
CParts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
DParts Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
EParts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
FFirst-Time Battery Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
GAssembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
HBattery Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
ICharging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
JBattery Handling/Care/Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
KRules for Safe Driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
LHow to Operate Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
MQuestions and Answers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
NProblems and Solutions Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
OStatement of Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
PAuthorized Service Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
4
Message to Parents
Thank you for purchasing the Power Wheels®
Kawasaki®ZX-7! For over 30 years, Power Wheels®
has manufactured high-quality, battery-powered
vehicles for children. Our goal is to provide your child
with an enjoyable and safe driving experience. To
help achieve this goal, it is extremely important that
you read this entire manual and share the appropriate
information with your child.
The Kawasaki®ZX-7 requires adult assembly. Please
set aside at least 30 minutes for assembly. Read the
assembly instructions carefully and identify all parts
before assembly. Refer to the Parts Section beginning
on page 6 for parts identification. Save all packaging
material until assembly is complete to ensure that no
parts are discarded.
In the unlikely event that parts are missing or
damaged or if you have any questions about your
Power Wheels®vehicle, please call our Consumer
Affairs toll-free service lines, open from 8 AM to 6 PM
(EST) Monday through Friday.
A
Please call us at 1-800-348-0751.
Trained customer service representatives are available
to take your call in English or French.
¿Habla Español? Si usted tiene alguna pregunta ó
necesita asistencia llame gratis 1-800-348-0755 para
los Estados Unidos. Tenemos representantes que
hablan español para atender su llamada. Este
manual tambien disponsible en Espanol.
We also have a nationwide Authorized Service Center
network – with over 300 Authorized Service Centers.
Our Authorized Service Centers will repair or replace
parts under warranty at no charge. For vehicles
beyond warranty, our Authorized Service Centers
will perform repairs for a minimal charge. For the
Authorized Service Center nearest you, please see
the Authorized Service Center listing beginning on
page 35.

Important Information
• Carefully read this manual for important safety
information and operating instructions before using
your vehicle.
• Please complete and return the enclosed Vehicle
Registration Card, or call 1-800-348-0751 to register
your vehicle by phone.
• The Kawasaki®ZX-7 is designed for use by children
11/2 - 4 years.
• Adult assembly is required.
• This vehicle uses a Power Wheels®Type H battery
with a Power Wheels®25 amp fuse and a Power
Wheels®Type H 6 volt charger (120 VAC 60 HZ 28W
with an output of 6 VDC 1200 mA). Do not
substitute any other battery, fuse or charger.
•Before first-time use, charge the battery for at
least 18 hours. Never charge the battery longer
than 30 hours.
• After the first charge, charge the battery a
minimum of 18 hours after each use. Never charge
the battery longer than 30 hours.
• Do not run down the battery completely before
charging.
• Leaving the battery in a discharged condition will
ruin it.
• Charge the battery before storing your vehicle.
• Charge the battery at least once per month, even if
the vehicle has not been used.
• Do not store the battery in temperatures above
75˚ F or below -10˚ F.
• Even with proper care, the battery will not last
forever. The life of the battery depends on how well
you follow the Battery Care instructions and the total
number of hours the battery is used. Please refer to
the Battery Handling/Care/Disposal instructions on
page 26 for detailed information about battery
care.
B
5
• To purchase a Power Wheels®Type H battery, Power
Wheels®25 amp fuse or a Power Wheels®Type H
6 volt charger, please contact:
- the store where your vehicle was purchased.
- an Authorized Service Center (see Authorized
Service Center list beginning on page 35).
- Power Wheels®Consumer Affairs at 1-800-348-0751.
• While the battery is charging, the charger may
become warm to the touch. This is normal, and does
not indicate a problem.
• The Kawasaki®ZX-7 is suitable for use on asphalt,
cement or other hard surfaces. To prevent damage
to the motor and switches, do not operate the
vehicle on loose dirt, gravel or sand.
• The Kawasaki®ZX-7 is not designed for use on
grass or hills. For best traction, use only on asphalt,
cement, or other flat, hard surfaces.
• To prevent damage to electrical components, store
the Kawasaki®ZX-7 inside or under a protective
cover during snowy or rainy weather. Do not leave
the Kawasaki®ZX-7 out in the rain or let your child
wash it with soap and water.
• The Kawasaki®ZX-7 has a special circuit-breaker
in the wiring to protect the motor and electrical
system. If the vehicle is put under extreme load
(driving on rough surfaces, too much weight,
climbing too steep of an incline), the circuit-breaker
will shut the electrical system down for up to 20
seconds. If the system repeatedly shuts down, the
driving conditions may be too demanding (ie: too
steep or too much weight).
• Metal parts have been coated with a lubricant to
protect them during shipment. Wipe all metal parts
with a paper towel to remove any excess lubricant.

Parts
C
Not Shown:
Literature Bag
6-VOLT
CHARGER
Small Parts Bag
Hubcap – 2
Battery Retainer
6
If you experience a problem with this product, or are missing a part, please call us at
1-800-348-0751, rather than return this product to the store.
Please save all packaging material until assembly is complete to ensure that no parts are discarded.
Dashboard
Microphone
Windshield
Shock Set – 1
Headlight Lens Set
Fender
Hand Grips – 2
6 Volt Charger

Wheel Bushing – 2
#6 x 3/8" Screw – 2
#8 x 7/8" Screw
Cap Nut – 3* #8 x 11/2" Screw – 4
25 Amp Fuse –2*
Radio Knob – 2
Fairing
Not Shown: Label Sheets 6 Volt Battery
L
Left Handlebar
7
Parts
Gas Cap
#8 x 3/4" Screw – 4
All Screws Shown
Actual Size
Vehicle Body
Seat
Front Axle
Right Handlebar
Front Wheel
*For your convenience, an extra 25 amp fuse
and cap nut have been included.
Key Assembly
Handlebar Plug – 2

Parts Diagram
FOR MODEL 78410
6 VOLT
8
Kawasaki®ZX-7
44
45
46 48
621
12
19
CHARGER
18 15
17
16
49
43
42
41 14 13
12
9
8
39
38
40
37
12
36
52
10
35
34
33
32
2
31
30
1
29
28
22
4
51
20
27
26
25
5
7
23
24
17
11
50
ASSEMBLY A
MOTOR/GEARBOX ASSEMBLY
SEE
ASSEMBLY A

Parts List
E
Item
No. Description Part No. Qty.
1 Battery 80008-0110 1
2 25 amp Fuse 80014-0070 1
3 Wheel Driver Screw 80006-0017 1
4 Foot Switch 80014-0022 1
5 Motor/Gearbox Assembly 74780-0640 1
6 Wiring Harness 80064-0083 1
7 Driver 80001-0247 1
8 Windshield 80063-0068 1
9 Lens Cover Set 80030-0074 1
10 .354 Retainer w/Body 80047-0104 2
11 7/16" Washer 80061-0039 2
12 11/2" Screw 80006-0175 5
13 Handgrip 80028-0016 2
14 Right Handlebar 80029-0020 1
15 Shock Set 80001-0435 1
16 Front Axle 80025-0027 1
17 .437 Retainer w/Body 80047-0106 4
18 Front Hubcap 80033-0077 2
19 Wheel Spacer 80009-0060 5
20 Front Wheel 80062-0036 1
21 Footboard Cover 80023-0033 1
22 Foot Pedal w/Spring Clip 80041-0004 1
23 Rear Wheel 80062-0047 2
24 Rear Hubcap 80033-0076 2
25 Motor Cover 80039-0052 1
26 Rear Axle 80046-0090 1
27 Axle Spacer Tube 80052-0012 1
28 Body 80005-0340 1
29 Trunk Lid 80001-0511 1
30 Battery Retainer 80047-0022 1
31 7/8" Screw 80006-0173 1
32 Seat 80067-0064 1
33 Gas Cap 80001-0512 1
34 Pivot Pin 80006-0027 1
35 Left Handlebar 80029-0041 1
36 Key Housing 80001-0281 1
37 Fairing 80063-0122 1
38 Microphone 80038-0009 1
39 3/8” Screw 80006-0171 2
40 Dash 80016-0047 1
41 Swivel Bracket 80007-0005 1
42 3/4" Screw 80006-0172 4
43 Fender 80022-0065 1
44 Motor 80039-0043 1
45 Drive Gear Metal 80026-0098 1
46 Gearbox 80026-0056 1
47 Lock Fastener 80001-0622 1
48 Motor Bolt 80006-0052 2
49 Flex Plate 80001-0305 1
50 Rectangular Wheel Bushing 80009-0052 2
51 1" Screw 80006-0032 1
52 Radio Knobs 80045-0025 2
Parts Not Shown
#6 - 20 x 1" Screw for
Swivel Bracket 80006-0034 1
11/4" Screw for Flex Plate 80006-0022 2
Handlebar Plugs 80047-0026 2
Literature Bag 80034-0772 1
Adhesive Harness Clip 80023-0088 1
Main Decal Sheet 80017-0458 1
Paper Decal Sheet 80017-0457 1
Headlight Decal Sheet 78410-0300 1
9
Note: The parts listed below are not all consumer assembled. Consumer assembled parts are
shown on pages 6 and 7 and are highlighted in bold type below.

10
First-Time Battery Charging
F
WARNING
• The battery must be handled by adults only.
• Never allow children to charge the battery. Battery charging must be done by adults only.
A child could be injured by the electricity involved in charging the battery.
• Use of the wrong type battery, fuse or charger could cause a fire or explosion, resulting in
serious injury.
• Children can be harmed by small parts, sharp edges and sharp points in the vehicle’s
unassembled state, or by electrical items. Care should be taken in unpacking and assembly
of the vehicle. Children should not handle the battery or other parts, or help in assembly.
• Never permit a child to handle the battery. The battery is heavy and contains sulfuric acid
(electrolyte), and if dropped, could result in serious injury. Read the cautions on the back
panel of the battery.
• Never lift or carry the battery by the wires or connector. This can damage the battery and
possibly cause a fire. Lift and carry the battery by the case only.
• Examine the battery, charger and their connectors for excessive wear or damage each time
you charge the battery. If damage or excessive wear is detected, do not use the charger or
the vehicle until you have replaced the worn or damaged part.
• Never alter this vehicle or its electrical system in any way. Alterations could cause a fire
resulting in injury and could also ruin the electrical system.
• Never add unauthorized parts to the vehicle or use substitute parts. Use only specified Power
Wheels®replacement parts.
CAUTION
• Do not operate the vehicle for the first time until you have inserted a 25 amp fuse into the
battery and charged the battery for at least 18 hours. Never charge the battery longer than
30 hours.
• Read and follow the Battery Care instructions on page 26. Failure to follow the Battery Care
instructions may permanently damage your battery and may void your warranty.
• Use the charger indoors only.
We recommend that you begin charging your battery before beginning assembly of your
vehicle. Your new battery must be charged for at least 18 hours before using your vehicle for
the first time.

®
®
• Squeeze the Lock-InTM connector
tabs on the charger connector
and plug it into the battery
connector.
• Plug the charger into a standard
120 volt wall outlet.
Note: If power flow to the wall
outlet is controlled by a switch,
make sure the switch is “ON”.
• Before first time use, charge the
battery for at least 18 hours.
Never charge the battery longer
than 30 hours.
Note: The battery must be upright
while charging.
2
3
Battery
Connector
Charger
Connector
Lock-InTM
Connector
Tabs
First-Time Battery Charging
11
• Insert the 25 amp fuse into the
battery.
IMPORTANT
A25AMPFUSEMUST
BEINSTALLEDINTOP
OFBATTERYBEFORE
TOYWILLRECHARGE
OROPERATE
®
1
Fuse
Charger

Assembly
Do Not Omit Any Steps. Please set aside at least 30 minutes for assembly.
• Position a handlebar plug against
the top end of a handlebar.
• Moisten a hand grip with warm
water.
• Slide the hand grip onto the end
of the handlebar.
• Repeat this procedure to attach
the other handlebar plug and
handgrip to the other handlebar.
• Stand the vehicle body on its rear
wheels.
• Slide the left handlebar through
the holes in the left side of the
swivel bracket.
Please Note: The left handlebar is
marked “L”; the right handlebar is
marked “R”.
L
Handlebar Plug
1
2
12
G
WARNING
•Children can be harmed by small parts, sharp edges and sharp points in the vehicle’s
unassembled state, or by electrical items. Care should be taken in unpacking and assembly
of the vehicle. Children should not handle the battery or other parts, or help in assembly.
• Keep small parts and plastic bags out of children’s reach. Dispose of plastic bags properly.
Hand Grip
Swivel Bracket
Left Handlebar

• Apply labels to the dashboard as
shown.
• Make sure the areas where the
labels will be applied are clean
and dry.
• For best adhesion, avoid applying
labels more than once.
4
• Snap the key assembly and radio
knobs into the dashboard.
Please Note: Gently squeeze the
tabs on the radio knobs together
before inserting the knobs into the
dashboard.
• Insert the microphone cord
through a hole in the dashboard,
as shown. Make sure the end of
the microphone cord forms a “T”
behind the dashboard so that it
stays secure in the dashboard.
13
Assembly
3
5
• Align the screw holes in the left
side of the swivel bracket with the
screw holes in the left handlebar.
• Insert two #8 x 3/4" screws into the
left handlebar.
• Tighten each screw with a Phillips
screwdriver. Do not over-tighten.
• Repeat steps 2 and 3 to assemble
the right handlebar to the vehicle
body.
#8 x 3/4" Screw – 2
Shown Actual Size
910
Swivel Bracket
Left Handlebar
Dashboard
Microphone
Radio Knobs
Key Assembly
Dashboard

• Insert the four tabs on the
underside of the windshield into
the holes in the fairing.
• Press firmly on the windshield to fit
the tabs into the holes.
7
14
Windshield
Assembly
Fairing
• Lay the vehicle body on its belly.
• Fit the dashboard onto the top
of the swivel bracket.
• Align the screw holes in the
dashboard and swivel bracket.
• Insert two #8 x 11/2" screws into
the dashboard.
• Tighten each screw with a Phillips
screwdriver. Do not over-tighten.
6
Dashboard
#8 x 11/2" Screw – 2
Shown Actual Size
Swivel
Bracket

Assembly
• Stand the vehicle body on its
rear wheels.
• Fit the fairing onto the front of the
swivel bracket.
• Align the screw holes in the front
of the fairing with the holes in the
swivel bracket.
• Insert two #8 x 11/2" screws into
the fairing.
• Tighten the screws with a Phillips
screwdriver. Do not over-tighten.
9
Swivel Bracket
Fairing
Windshield
Fairing
• Turn the fairing over.
• Insert two #6 x 3/8" screws into the
holes in the two long windshield
tabs.
• Tighten each screw with a Phillips
screwdriver. Do not over-tighten.
8
#6 x 3/8" Screw – 2
Shown Actual Size
15
#8 x 11/2" Screw – 2
Shown Actual Size
Long Windshield Tabs

• Fit the fender onto the ends of
the handlebars.
• Slide the fender up the handle-
bars to the fairing.
10
• Fit one end of the front axle into
a cap nut.
• Tap the front axle with a hammer
to secure the cap nut on the
front axle.
11
Assembly
16
12
• Remove the rubber bands from
the shock sets and dispose of the
rubber bands.
• Using safety scissors, cut the four
shock set halves from the runner.
Carefully trim excess plastic and
dispose of the runner and all
excess plastic.
• Sort the shock halves into inner
shock halves and outer shock
halves.
Please Note: The inner shock halves
have an extension.
Fender
Handlebars
Fairing
Cap Nut
Front Axle
Outer
Shock
Halves
Inner
Shock
Halves
Runner
✁
✁
✁
✁
✁
✁
✁
✁

14
Assembly
• Slide the front axle through the
hole in the shock halves and
handlebar.
13
17
15
• Fit and hold an inner shock half
to the inside of a handlebar.
• Fit and hold an outer shock half
to the outside of the same
handlebar.
• Make sure the top ends of the
shock halves fit into the fender.
• Fit a wheel bushing into the hole
in the center of the front wheel.
• Repeat this procedure to fit the
remaining wheel bushing into the
hole on the other side of the front
wheel.
Inner Shock Half
Fender
Outer Shock Half
Front Axle
Front Wheel
Wheel Bushing

18
Assembly
• Fit and hold an inner shock half
to the inside of the exposed
handlebar.
• Fit and hold an outer shock
half to the outside of the same
handlebar.
• Make sure the top ends of the
shock halves fit into the fender.
16
• Position the front wheel between
the handlebars.
• Slide the front axle through the
front wheel.
17
18
• Fit and hold the hubcaps to
each side of the front wheel.
• Make sure the posts on the inside
of the hubcaps fit into the inden-
tations on the front wheel, so that
the hubcaps lay flat against the
wheel.
Hubcap
Front Wheel
Front Wheel
Front Axle
Front Wheel
Fender
Outer Shock Half
Inner
Shock
Half

Assembly
• Position the vehicle upright.
• Apply headlight labels to the
fairing as shown.
• Make sure the areas where the
labels will be applied are clean
and dry.
• For best adhesion, avoid applying
labels more than once.
19
L
• Align the “L” on the left headlight
lens with the “L” in the left head-
light on the fairing.
• Insert the tabs on the headlight
lens into the slots in the fairing.
• Press firmly to snap the headlight
lens into the fairing.
• Repeat this procedure to
assemble the right headlight lens
(marked “R”) to the fairing.
20
• Slide the front axle through the
handlebar.
• Fit the remaining cap nut on the
end of the front axle.
• Support the front axle and tap the
cap nut with a hammer to secure
it on the end of the front axle.
21
19
“L”
Cap Nut
Front Axle Handlebar

• Snap the gas cap into the vehicle
body.
22
• Insert the tabs on the front of the
seat into the vehicle body.
• Lower the seat.
23
Assembly
Proper label application will help to
keep the labels looking their best!
• Wash your hands before applying
the labels.
• Make sure the areas where the
labels will be applied are clean
and dry. Wipe your vehicle with a
clean, soft, dry cloth to remove
any dust or oils.
• For best results, avoid applying a
label more than once.
• Apply the labels as shown in the
illustrations.
• After applying a label, rub the
label firmly with a dry cloth to
make sure the label is adhered to
your vehicle.
One-time assembly is now
complete.
Important Note: Please carefully
read the owner’s information in this
manual and teach your child
about proper vehicle operation
and rules for safe driving before
allowing him to drive this vehicle.
BATTERY POWER BATTERY POWER
RECHARGEABLERECHARGEABLE
R
24
20
BATTERYPOWERED
BATTERY POWERED
RECHARGEABLE
RECHARGEABLE
12
3
4
5
13B
67811 12
13A
14
15
16
Gas Cap
Seat
Tabs