PowerShield Defender Series User manual

Defender Series
PSD 650 l 1200 l 1600 l 2000
Line Interactive UPS
Uninterruptible Power Supply System
Please read carefully the following safety instructions before using the Defender
650/1200/1600/2000.
Thank you for your purchasing the Defender 650/1200/1600/2000. It is designed
to provide safe and reliable power protection to your precious electronics equipment.
Before you start using the product, please read this user’s manual. It contains
instructions relating to safety, installation, operation maintenance and warranty.
Please keep this manual in a safe place for furture use.
1. Introduction

PowerShield Defender 650/1200/1600/2000VA unit
PowerShield Defender User’s Manual
USB Communication cable

PSD1200/1600/2000 PSD650
Breaker will trip when there is overload / short occurs at output of the unit.
Circuit breaker for 1200/1600/2000 is rated at 10Amp and for 650 is reated at
5Amp.

There is power distrbances / black
out. the unit is supplying power
from battery.
Beeps 2 beeps every 30 sec
The normal display of battery and
Battery Remain Time will
Exchange once per 5s.
The unit is boosting / bucking
input volage.
On line mode icon flashes every 1
sec.
No Beep
Utility is stable and the unit is
supplying its power from utility.
No beep
Battery capacity becomes low.
The unit will shut its output down.
On battery mode icon flashes.
Rapid beep one sec interval
Battery Remain
Time
Defender 650/1200/1600/2000VA have inbuilt native Battery management
compatible with Windows and Mac OS.
If you wish to use NetGuard monitoring Software please follow the instructions
below:
1. Please download the latest NetGuard Monitoring software from
www.powershield.com.au/index.php/downloads
2. When the installation is completed, NetGurad agent icon will appear on the
Task bar
3. Once installation is completed, click the plug icon found on the Task bar to
start the program
7. Software Installation
6. Understanding LCD display

Deffender 650/1200/1600/2000’s have a user replaceable battery feature. Please
read warning on the front page about battery safety and follow the steps carefully
shown below. Please use only PowerShield approved battery pack to maximize
the performance of the unit.
1. Shutdown all connected equipment and turn the UPS off by pressing on /off
button
2. Remove input cord from mains and remove all output cords from the UPS.
3. Flip the UPS upside down.
For Defender 1200/1600/2000, locate the Philips head screw on the bottom of
the front panel. Remove the screw using a Philips screw driver.
For Defender 650, locate the two slots on the bottom of the front panel. Insert a
flat head screw driver in one of the two slots. Press gently down towards front
while also gently levering the screw driver towards front. Repeat for the second
slot to unclip front panel.
4. Remove the front panel by grabbing the bottom edge of the front panel and pull
forward. Please be careful not to apply excess force to the panel as it may
cause damage to the LCD cable attached to it.
5. Remove the metal plate holding the battery pack in the enclosure by sliding it
upwards and then pull out.
6. Pull tag of the battery pack and remove the battery from the unit.
7. Remove Red (Positive) and Black (Negative) battery wires from the battery pack.
8. Prepare new battery pack. Connect Black (Negative) wire to the new battery
black terminal and connect Red (Positive) battery wire to the red battery terminal.
Note:You will see a small spark when you connect red wire to the battery. This is
normal as the unit charges some components. Please check polarity of battery
terminals.
9. Insert the battery back into the unit and put the metal plate back in to the front of
the enclosure. Replace the front panel. For Defender 1200/1600/2000, fasten the
Philips screw.
10. Please recharge the unit for 6 hours before you turn the unit on.

PSD2000
PSD1600
PSD1200
PSD650
2000VA/1200W
1600VA/960W1200VA/720W650VA/390W
312Joules/
6500Amps
12.86kg
11.5kg
11.1kg5.2kg