Powertrain MX2 User manual

1
MOTORIZED TREADMILL –MODEL MX2
INSTRUCTION MANUAL
Please read these instructions carefully before use and keep for future reference.
Due to constant improvements some images and features may not be applicable.
FOR DOMESTIC INDOOR USE ONLY
WARNING: Keep young children away from this machine at all times. Contact with
the moving surface may result in severe friction burns.

2
1. CAUTION
To avoid injuries please read this manual carefully before using the treadmill.
Before starting any exercise program you should consult your doctor to determine if
you have any physical or health conditions which could create a risk to your health and
safety, or prevent you from using the equipment properly. Your doctor’s advice is
essential if you are taking medication that affects your heart rate, blood pressure or
cholesterol level.
Ensure you have tightened all the bolts and nuts on this machine before commencing
any exercise.
For safety reasons do not stand on running belt whilst starting the unit.
Please stop immediately if you feel unwell or nauseous.
Please adjust speed slowly.
Adjustment of belt is prohibited during use.
It is recommended that you wear sports shoes and appropriate clothing when using the
treadmill
Children, elderly, pregnant women and people with medical conditions should not use
the treadmill unless authorized by their doctor and in the presence of an adult who may
assist.
Clip the safety key on your clothing during use.
Firmly hold the handle bars during use.
Keep the safety key away from children when the treadmill is not in use, as it may
present a choking hazard.
Keep silicone oil away from children’s reach. If accidentally swallowed or comes into
contact with eyes, use water to wash out and immediately seek medical assistance.
The heart rate function is to be used as an exercise reference feature only and is not to
be relied on for accurate heart rate assessment and is not to be used for medical
purposes. Should you feel unwell, stop exercising immediately and contact your doctor.
2. SAFETY NOTICE
Please place the machine on flat ground. It is unsuitable to use the machine in the
following situations:
oOutdoors. (The machine is specially designed for indoor use only)
oSlant ground or slant places on balcony.
oSunlit area or near heater.
oBig noisy places.
Machine requires a constant a.c 220-240V power connection

3
Error may be displayed if power is not stable. Please do not share points with integral
equipment such as computers, air conditioners etc.
Be careful of children or other objects while folding and unfolding the machine.
Do not put machine near wet objects to avoid slippery surfaces and damage to
machine
3. CAUTION PRIOR TO USE
Do not use the machine if you are unwell and immediately stop using the machine if
you start feeling unwell whilst using it.
Disconnect the machine from power when not in use.
Prior to relocating or folding the machine, disconnect it from power.
Machine is to be used on a flat surface only.
Ensure a 2m clearance around the machine is available prior to using it.
Do not start the machine when it is folded.
Keep all liquids away from the machine as they will damage the unit and void all
warranty.
Machine is not to be used in poorly ventilated spaces or locations with flammable
objects in its vicinity.
Do not put any objects on the machine.
Switch off all functions and disconnect from power when not in use.
Please do not stand directly on the belt while starting the machine.
Do not disassemble the machine without a written authorization from the manufacturer
Please make sure the running belt is fastened before use
Before folding the machine ensure that the gradient is set on “zero”, failing to do so will
damage the unit.

4
4. PRODUCT SPECIFICATIONS
Main Specifications and Parts list
Main Specifications
No.
Parameters Names
Description
1
Input power voltage
AC220-240V,50hz
2
Motor power
3.0HP
3
Speed
1.0-20.0Km/h
Packing list
No.
Name
units
Qty
1
Treadmill Unit
set
1
2
Accessories
pc
1
Tools
No.
Name
Qty
No.
Name
Qty
1
Inner hexagon wrench 6mm
1
8
Audio cable
1
2
Inner hexagon wrench 5mm
1
9
Base cover
1
3
Open spanner 13-15
1
10
Screws M8*55
2
4
Screwdriver
1
11
Screws M8*20
6
Console
Pulse Sensors
Handle bar
Upright column
Motor cover
Side rail
End cap
Foot pad
Wheels
Cover

5
5
Silicone oil
1
12
Screws M8
2
6
Manual
1
13
Washerφ8
8
7
Safety Key
1
14
Screw M5*8
4
5. ASSEMBLY INSTRUCTIONS
During assembly, first insert and moderately tighten screws and when the frame has
been fully assembled, inspect all the screws and tighten them completely.
Lay unit flat on the ground. Cut the nylon cable ties (where supplied) on the base. Lift
the upright columns and console in the direction shown in the diagram below.
WARNING: THIS PRODUCT IS HEAVY. ENSURE TWO PEOPLE ARE ASSEMBLING
IT ATALL TIMES
Use the inner hexagon spanner (#5) and insert screws M8*55 to attach the columns to
the base of the treadmill (as shown in the diagram below).
Use screw M8 to tighten it (Step A), followed by screws M8*45 to lock washer and nut
(Step B).
A
B

6
Use an inner hexagon spanner (#5) and screw M8*20 to lock console to the column.
Use a screwdriver and insert screws M5*8 to attach the corner covers around the base
on both sides of the treadmill.
Position the safety key in the correct position as shown below.
Safety Key Function
oDisconnecting the safety key will immediately stop the running track and the
screen will display “Error”, and the treadmill will emit a beep.
oPlacing the safety key back on the designated area on the console will clear all
data in 2 seconds.
o
Safety key

7
CAUTION: Please confirm that all screws are correctly tightened according to the
requirements after installation and check no part has been left out prior to
connecting to power.
6. USING THE TREADMILL
Power on –Connect the power adapter to a power point and turn on the unit by
using the red switch. The LED will illuminate and the treadmill will emit a beeping sound.
The screen on the control panel will switch on.
Display and Keys instructions：
oLCD functions：
Speed Display - the range：1.0-20.0KM/H，
Distance display - Display distance data.
Calorie display - Display calorie data.
Incline/ heart rate display：Display Incline / heart rate data
Incline range：0-15%
Pulse Function：50-200 (The heart rate function is to be used as an
exercise reference feature only and is not to be relied on for accurate heart
rate assessment and is not to be used for medical purposes. Should you
feel unwell, stop exercising immediately and contact your doctor).
Start - starts after 3 second countdown.
Stop –Pressing the Stop key will gradually stop the treadmill and clear all data.

8
Incline 3%, 5%, 8%, 12% and 15% Shortcuts –In running mode these keys are used
as shortcuts to set incline levels.
Speed 3km/h, 6km/h, 7km/h, 9km/h, 12km/h and 16km/h Shortcuts –In running
mode using these shortcuts will change the running speed accordingly.
Mode key - in standby mode this key will cycle through Countdown Running Modes:
Time Countdown, Distance Countdown and Calorie Countdown. When selecting modes
you can use speed +/- and incline +/- to select the relevant modes. Once selected,
press start key to turn on treadmill.
o“0:00” - manual mode，
o“15:00” - time countdown mode，
o“1.00” - distance countdown mode，
“50.0” - calorie countdown mode
Prog key -in standby mode this key will cycle through the various programs
“P01-P02-… -P12 -FAT” (1 through to 12, “FAT” is body fat test mode).
Speed +/- key
oIn running mode these keys are used to adjust the speed.
oIn standby mode these keys are used to set the values for the programs and
modes.
Incline +- key
oIn running mode these keys are used to adjust the incline gradient.
oIn standby mode these keys are used to increase/ decrease the setting value.
USB
oNext, voice +/- key：adjust functions of USB playing.
Fan key：turn on or turn off the fan.
Fixed Program / Starting instruction：
oMode instruction：one manual mode，including：normal mode，time countdown
mode, distance countdown mode and calorie countdown mode.
Starting instruction：
oPlace the safety key in the allocated position.
oPress start/stop key，the speed display will countdown from 5 and a notification
tone will be emitted out every time the number decreases, with running mode
commencing at the end of the countdown.

9
Manual Model Configuration：
oHow to enter manual mode：
Turn on the power switch which will default to the manual mode.
In standby, press Mode key to enter manual mode.
oManual mode includes three settings: time, distance, and calorie (in that
sequence).
oEntering manual mode, the time display on the screen will display 0:00.
Time countdown: Display will show the time and flash. Default time
countdown is 15:00. Use speed up/down keys or incline up/down keys, to
set time countdown. Time range is 5:00-99:00.
Distance countdown: Default distance setting is 1.00 km. Use speed
up/down keys or incline up/down keys to set distance countdown. Distance
range is 1.0-99 km. Each increment is 1km.
Calorie countdown. Default calorie setting is 50 kcal. Use speed up/down
keys or incline up/down keys to set the calorie countdown. Calorie range is
is 10.0-999 kcal. Each increment is 1 kcal.
Using Manual Mode
oPress start/stop key which will commence the 3 second countdown, followed by
the motor engaging. Default speed is 1.0KM/H.
oUse speed up/down key to adjust speed or the speed shortcuts.
oUse incline up/down to adjust incline or the incline shortcuts.
oWhen the motor is running, pressing start/stop key will stop the running mat.
oWhen the set time/calorie set/distance set reaches zero a sound tone will be
emitted with the speed gradually decreasing until the treadmill comes to a full
stop.
oWhen the set numbers reach the maximum allowed range, all the data will be
cleared and the setting will recommence. In manual mode, when the cumulative
time is over 99:59(100 minutes), the time will restart at 0:00.
oEach program is divided into 20 periods, and the time of every period is 1/20 of
the total time. When commencing the new program, a tone sound will be
emitted.
FAT Function
In standby mode, press program button to enter the FAT function
oF1--Gender, screen displays 01 stand for male, 02 stand for female. Press
SPEED+ or Speed- to select gender. Press MODE to confirm.
oF2--Age, the value range for age is 10-99 years, Press SPEED+ or Speed- to
select age. Press MODE to confirm.
oF3--Height, height value range is 100-200cm. Press SPEED+ or Speed- to
select height. Press MODE to confirm.
oF4--Weight, weight value range is 20-200kg. Press SPEED+ or Speed- to select
weight. Press MODE to confirm.

10
oF5--FAT Index, the screen will display ----Hold the heart rate sensor with your
hands for 8 seconds, and then the FAT index will show on the screen.
Programs tabled below.
Time
Program
Set Time/10=Running time of each period
1
2
3
4
5
6
7
8
9
10
P1
SPEED
3
3
6
5
5
4
4
4
4
3
INCLINE
0
3
3
3
4
4
4
1
1
0
P2
SPEED
3
3
4
4
5
5
5
6
6
4
INCLINE
2
2
2
3
3
3
3
4
4
2
P3
SPEED
2
4
6
8
7
8
6
2
3
2
INCLINE
3
5
4
4
3
4
4
3
4
2
P4
SPEED
3
3
5
6
7
6
5
4
3
3
INCLINE
0
3
3
2
2
5
5
3
3
2
P5
SPEED
3
6
6
6
8
7
7
5
5
4
INCLINE
3
5
3
4
2
3
4
2
3
2
P6
SPEED
2
6
5
4
8
7
5
3
3
2
INCLINE
3
4
5
6
3
5
5
6
4
3
P7
SPEED
2
9
9
7
7
6
5
3
2
2
INCLINE
0
3
3
3
4
4
4
1
1
0
P8
SPEED
2
4
4
4
5
6
8
8
6
2
INCLINE
1
1
4
4
4
5
5
4
3
2
P9
SPEED
2
4
5
5
6
5
6
3
3
2
INCLINE
3
5
3
4
2
3
4
2
3
2
P10
SPEED
2
5
7
5
8
6
5
2
4
3
INCLINE
1
5
6
8
12
9
10
9
5
3
P11
SPEED
2
5
6
7
8
9
10
5
3
2
INCLINE
3
5
6
8
6
5
8
7
5
2
P12
SPEED
2
3
5
6
8
6
9
6
5
3
INCLINE
5
7
5
8
6
5
9
10
6
2

11
Error Codes
Error code
Description
Solution
E1
Erroneous Connection:
when the power is on, the
connection between lower
controller and the console is
abnormal.
Possible Cause: the communication between the lower controller
and console is blocked, check each joint between the controller and
console, make sure that each core is fully plugged in. Check the
connection line, replace it if is damaged.
E2
No signal from motor.
Possible Cause: Check the motor cable to see whether it is
connected well or not, if not, re-connect the motor wire again.
Check the motor cable to see whether it is damaged or has a burnt
smell, if yes, replace the motor.
E5
Current overload
protection:
Whilst in use, the lower
controller detects the current
to be over 6A for more than
3 seconds.
Possible Cause:
Overloading leads to excessive current, and the system stops out of
self-protection, or some part is stuck, causing the motor to stop.
Adjust the treadmill and restart it. Check if there is liquid or burnt
smell while the motor is running, if yes, replace the motor; check if
the controller has a burnt smell, if yes, replace the controller; check
the power supply voltage, if it does not match the specifications,
change into correct voltage and test the machine again.
E6
Explosion-proof impact
protection: the abnormal
voltage or motor cause a
circuit fault which drives the
motor.
Possible Cause:
Check if the power supply voltage is 50% lower than normal
voltage，use the correct voltage and test the machine again；check
if the controller has a burnt smell and replace the controller; Check
if the motor cable is connected and connect the motor wire again.
E7
No safety key
Put the safety key on the right place.
7. Maintenance
Warning: Before cleaning or carrying out any maintenance, ensure the treadmill is
disconnected from power
Comprehensive cleaning will extend the life of your treadmill
Remove dust periodically in order to maintain all parts clean.
Be sure to clean running belt with both sides of the exposed portion, which will reduce
the accumulation of impurities.
Make sure to wear clean athletic shoes to avoid introducing dirt on to the running board
and belt.
Treadmill belts must be cleaned with a damp cloth with a mild soap.
Ensure none of the components and the treadmill itself come into contact with liquids
which will void all warranty.
Warning: Make sure power plug is disconnected before removing the motor cover.
Clean the motor at least once a year.

12
5. Routine maintenance and Instructions
Warning: Before cleaning or maintaining products, please be sure the power plug is pulled out of
the electric treadmill.
Cleaning: Comprehensive cleaning will extend the life of the electric treadmill.
Remove dust periodically in order to keep the parts clean. Be sure to clean running belt with both
sides of the exposed portion, which will reduce the accumulation of impurities. Make sure to wear
clean athletic shoes to avoid carrying the dirty matters into running board and belt. Treadmill belts
shall be cleaned by a damp cloth with soap water. And please pay attention not to wet the electrical
components and running belt.
Warning: before opening the front cover make sure that the electric treadmill’s power plug is pulled
out. Open the front cover of motor and vacuum the motor at least once a year.
Maintenance of the Running Board and Belt - Lubrication and Cooling
Your treadmill's running board and running belt had been lubricated at the factory.
Friction between the running belt and running board has a great impact on the life and
performance of your treadmill.
Regular application of treadmill lubricant is needed. We advise you to check the board
regularly.
To check if the belt needs to be lubricated, simply lit each side of the belt with your
hands and feel the top surface of the running deck. If it is slick to the touch, then no
lubrication is required. If it is dry to the touch, then lubricate.
To lubricate (where required):
oLift the edge of the running to expose the running deck.
oPlace a few drops of the lubricant (all purpose household oil or sewing machine
oil is suitable) along the centre of the running deck
oRun the treadmill (without the user) at a slow speed for up to 5 minutes to evenly
distribute the lubricant.
CAUTION: Do not over lubricate. Wipe away excess lubricant from the belt.
If the board’s surface is damaged, please contact our customer service center to
purchase replacement parts.
We recommend applying lubricant between running belt and running board:
oInfrequent user (use less than 3 hours a week) - once per month;
oFrequent user (use more than 7 hours a week) - once a fortnight.

13
To safeguard your treadmill and extend the life of the unit, it is recommended that after
2 hours of continued use, the machine be switched off and allowed to cool for a
minimum of10 minutes before using it again.
If the treadmill belt is loose, it will skid when running. Conversely, if it’s too tight, it may
reduce motor performance and harden the abrasion of roller and the running belt.
You can lift two sides of the running belt for 50-75mm to adjust the tightness.
Adjusting alignment and tightness
The running belt is adjusted at the factory, however after prolonged use it may stretch
and will require to be re-tensioned. For best use, it may be required to adjust the
running belt for its optimum alignment.
Running Belt alignment
Place treadmill flat on the floor but do not stand on it.
Turn on treadmill and set the speed at 6-8km/hour .
If the running belt is shifting to the right, rotate the right adjusting bolt with 1/2 turn
clockwise, then rotate the left adjusting bolt with 1/2 turn counter-clockwise. (Picture A)
If the running belt is shifting to the left, rotate the left adjusting bolt with 1/2 turn
clockwise, then rotate the right adjusting bolt with 1/2 turn counter-clockwise. (Picture
B)
Picture A Picture B
Multi-wedge Belt Tension Adjusting
After some time, the multi-wedge belt is expected to become loose as a result of the
abrasions, which will require the user to adjust the multi-wedge to ensure continued
safe use.
When to Adjust? Feeling of running with the occasional pause/slipping experienced,
indicates that the treadmill belt or multi-wedge belt are a little loose and further
assessment/confirmation is required.
Step 1: Which part is loose? Remove the four screws on protective cover, turn the
running speed to 1 km/h, stand on the running belt, grip the armrests, and tread the
treadmill belt slightly.( we advise treading the treadmill belts with the user's own weight)
oA. If instantaneous steps cannot stop the belt, the tightness is appropriate.
oB. If your instantaneous step stops the running belt, but the multi-wedge belt
and former roller is still running, it indicates that the running belt is loose and
appropriate adjustments must be made to facilitate the safe use

14
oC. If you observe that the instantaneous step makes both the treadmill belt and
multi-wedge belt stop, but the motor is still running, it indicates that the
multi-wedge belt is loose and appropriate adjustments must be made to
facilitate continuous safe use
Step 2: Use a wrench to adjust the screws on the motor base according to the
condition. Gently flip the multi-wedge belt between the motor shaft and the front roller,
if it is too loose, you can flip the multi-wedge belt by 100%; if it is too tight, the degree
for you to flip the belt is very limited. It is appropriate to flip the multi-wedge belt by 80%
after adjustment. Please adjust the tightness of the multi-wedge belt into the state that
it could be flipped by 80%.
Step 3: Lock the motor base and re- install the front cover.

15
Warranty and Contact Details
Kmate Pty Ltd provides a 12 month warranty for this product when used for domestic purposes. This product
is not intended for commercial use and any such use will void all warranty.
The benefits of this warranty are provided in addition to other rights and remedies you may have under a law
in relation to the goods and services to which this warranty relates. Our goods come with guarantees that
cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a
major failure and for compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have goods repaired or replaced if the goods fail to be of acceptable quality and the failure does
not amount to a major failure.
Before making a claim under warranty, please refer to your user/installation manual to ensure that you have
followed correct operating procedures of your product, and refer to the trouble shooting section (if such
exists) to assist solving any problems.
The warranty period begins from the day of purchase.
Your proof of purchase must be produced before assistance will be provided.
Where the Product is replaced pursuant to this Warranty, the replacement Product will be subject to the
warranty terms and warranty commencement date of the original product.
This warranty is only valid if the product is operated and maintained in accordance with the manufacturer’s
instructions.
Damage to property including but not limited to furniture, carpets, walls, ceilings or any other event either
directly or indirectly are excluded from warranty as well as any losses or expenses incurred by you in relation
to the product or making a claim under this warranty including without limitation any costs associated with
installation, reinstallation or transporting the product.
A claim may be refused if the defective claim has arisen for reasons other than a manufacturers fault or
defective parts or workmanship. Circumstances in which a warranty claim may be declined include, but are
not limited to the following:
Normal wear and tear;
Misuse or abuse (i.e., dislocation of the power cable due to tripping over it), including failure to
properly maintain or service;
Damages caused by improper or incorrect installation, force-majeure, electrical surges, lightning,
power grid fluctuations, water or by connection to alternative power supply sources (such as solar
inverters etc), are not eligible for warranty repair;
Insect or vermin infestation;
Failure to clean or improper cleaning and/or operation of the product;
Failure to periodically lubricate, adjust and maintain the treadmill;
If the product is modified without authorisation from Kmate Pty Ltd in writing;
If you are unable to supply a certificate of compliance for installation of any type as required by State
& Territory Laws
Contact Details
Kmate Pty Ltd
PO Box 234, Mount Waverley VIC 3149
Email: [email protected]om.au
Phone: [phone]
PLEASE CHECK THE LATEST VERSION AT:
https//kmate.com.au /MX2

16